JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
System Administration Guide: IP Services     Oracle Solaris 11 Express 11/10
search filter icon
search icon

Document Information

Preface

Part I TCP/IP Administration

1.  Planning an IPv4 Addressing Scheme (Tasks)

2.  Planning an IPv6 Addressing Scheme (Overview)

3.  Planning an IPv6 Network (Tasks)

4.  Configuring TCP/IP Network Services and IPv4 Addressing (Tasks)

5.  Enabling IPv6 on a Network (Tasks)

6.  Administering a TCP/IP Network (Tasks)

7.  Configuring IP Tunnels

8.  Troubleshooting Network Problems (Tasks)

General Network Troubleshooting Tips

Running Basic Diagnostic Checks

How to Perform Basic Network Software Checking

Common Problems When Deploying IPv6

IPv4 Router Cannot Be Upgraded to IPv6

Problems After Upgrading Services to IPv6

Current ISP Does Not Support IPv6

Security Issues When Tunneling to a 6to4 Relay Router

9.  TCP/IP and IPv4 in Depth (Reference)

10.  IPv6 in Depth (Reference)

Part II DHCP

11.  About DHCP (Overview)

12.  Planning for DHCP Service (Tasks)

13.  Configuring the DHCP Service (Tasks)

14.  Administering DHCP (Tasks)

15.  Configuring and Administering the DHCP Client

16.  Troubleshooting DHCP (Reference)

17.  DHCP Commands and Files (Reference)

Part III IP Security

18.  IP Security Architecture (Overview)

19.  Configuring IPsec (Tasks)

20.  IP Security Architecture (Reference)

21.  Internet Key Exchange (Overview)

22.  Configuring IKE (Tasks)

23.  Internet Key Exchange (Reference)

24.  IP Filter in Oracle Solaris (Overview)

25.   IP Filter (Tasks)

Part IV Networking Performance

26.  Integrated Load Balancer Overview

27.  Configuration of Integrated Load Balancer Tasks

28.  Virtual Router Redundancy Protocol (Overview)

29.  VRRP Configuration (Tasks)

30.  Implementing Congestion Control

Part V IP Quality of Service (IPQoS)

31.  Introducing IPQoS (Overview)

32.  Planning for an IPQoS-Enabled Network (Tasks)

33.  Creating the IPQoS Configuration File (Tasks)

34.  Starting and Maintaining IPQoS (Tasks)

35.  Using Flow Accounting and Statistics Gathering (Tasks)

36.  IPQoS in Detail (Reference)

Glossary

Index

Common Problems When Deploying IPv6

This section describes issues and problems that you might encounter while planning and deploying IPv6 at your site. For actual planning tasks, refer to Chapter 3, Planning an IPv6 Network (Tasks).

IPv4 Router Cannot Be Upgraded to IPv6

If your existing equipment cannot be upgraded, you might have to purchase IPv6-ready equipment. Check the manufacturers' documentation for any equipment-specific procedures you might have to perform to support IPv6.

Certain IPv4 routers cannot be upgraded for IPv6 support. If this situation applies to your topology, physically wire an IPv6 router next to the IPv4 router. Then, you can tunnel from the IPv6 router over the IPv4 router. For tasks for configuring tunnels, refer to Tunnel Configuration and Administration With the dladm Command.

Problems After Upgrading Services to IPv6

You might encounter the following situations when preparing services for IPv6 support:

Current ISP Does Not Support IPv6

If you want to deploy IPv6 but your current ISP does not offer IPv6 addressing, consider the following alternatives to changing ISPs:

Security Issues When Tunneling to a 6to4 Relay Router

By nature, a tunnel between a 6to4 router and a 6to4 relay router is insecure. Security problems, such as the following, are inherent in such a tunnel:

These problems and other security issues that are inherent with 6to4 relay routers are explained in the Internet Draft, Security Considerations for 6to4. Generally, you should consider enabling support for 6to4 relay routers for the following reasons only: