Oracle® Fusion Middleware Enterprise Deployment Guide for Oracle Business Intelligence 11g Release 1 (11.1.1) E15722-01 |
|
![]() Previous |
![]() Next |
This chapter describes the software installations required for the enterprise deployment reference topology for Oracle Business Intelligence. The installation is divided into two parts. The first part covers the required Web tier installation, while the second part addresses the required Oracle Fusion Middleware components. Later chapters describe the required configuration steps to create the reference topology for Oracle Business Intelligence.
Important: Oracle strongly recommends that you read Oracle Fusion Middleware Release Notes for any additional installation and deployment considerations before starting the setup process. |
This chapter contains the following topics:
Table 3-1 shows what software should be installed on each host or be accessible from each host.
Table 3-1 Software To Be Installed on Each Host or Accessible From Each Host
Hosts | OHS | WLS | BI |
---|---|---|---|
WEBHOST1 |
Yes |
No |
No |
WEBHOST2 |
Yes |
No |
No |
APPHOST1 |
No |
Yes |
Yes |
APPHOST2 |
No |
Yes |
Yes |
Table 3-2 shows the software versions used.
This section contains the following topics:
Before installing Oracle HTTP Server (OHS), check that your computers meet the following requirements:
Ensure that the system, patch, kernel, and other requirements are met as specified in the installation documentation.
Because Oracle HTTP Server is installed on port 7777 by default, you must ensure that port 7777 is not used by any service on the nodes. To check if this port is in use, run the following command before installing Oracle HTTP Server:
netstat -an | grep 7777
You must free port 7777 if it is in use.
On Linux platforms, if the /etc/oraInst.loc file exists, check that its contents are correct. Specifically, check that the inventory directory is correct and that you have write permissions for that directory. If the /etc/oraInst.loc file does not exist, you can skip this step.
Before starting the installation, ensure that the following environment variables are not set:
LD_ASSUME_KERNEL
ORACLE_INSTANCE
As described in Section 2.3, "Shared Storage and Recommended Directory Structure," you install Oracle Fusion Middleware in at least two storage locations for redundancy.
Start the installer for Oracle HTTP Server from the installation media:
./runInstaller
In the Specify Inventory Directory screen, do the following:
Enter HOME/oraInventory, where HOME is the home directory of the user performing the installation (this is the recommended location).
Enter the OS group for the user performing the installation.
Click Next.
Follow the instructions on screen to execute /createCentralInventory.sh as root.
Click OK.
In the Welcome screen, click Next.
In the Select Installation Type screen, select Install Software - Do Not Configure, and click Next.
In the Prerequisite Checks screen, verify that all checks complete successfully, and click Next.
In the Specify Installation Location screen, specify the following values:
Oracle Middleware Home: ORACLE_BASE/product/fmw
Oracle Home Directory: Oracle_WT1
Click Next.
In the Specify Security Updates screen, choose whether you want to receive security updates from Oracle support and if you do, enter your e-mail address.
In the Installation Summary screen, review the selections to ensure they are correct. If they are not, click Back to modify selections on previous screens. When you are ready, click Install.
On UNIX systems, if prompted to run the oracleRoot.sh script, make sure you run it as the root user.
The Oracle HTTP Server software is installed.
In the Installation Progress screen, click Next.
In the Installation Complete screen, click Finish to exit.
This section describes how to install the required Oracle Fusion Middleware software for the enterprise deployment reference topology for Oracle Business Intelligence. The software components to be installed consist of the WebLogic Server home (WL_HOME) and Oracle home (ORACLE_HOME). As described in Section 2.3, "Shared Storage and Recommended Directory Structure," you install Oracle Fusion Middleware in at least two storage locations for redundancy.
Important: Oracle strongly recommends that you read Oracle Fusion Middleware Release Notes for any additional installation and deployment considerations before starting the setup process. |
This section covers the following topics:
Perform these steps to install Oracle WebLogic Server on APPHOST1 and APPHOST2:
Start the installer for Oracle WebLogic Server from the installation media.
In the Welcome screen, click Next.
In the Choose Middleware Home Directory screen, do the following:
Select Create a new Middleware Home.
For Middleware Home Directory, enter ORACLE_BASE/product/fmw.
Note: ORACLE_BASE is the base directory under which Oracle products are installed. The recommended value is/u01/app/oracle . See Section 2.3, "Shared Storage and Recommended Directory Structure" for more information. |
Click Next.
In the Register for Security Updates screen, choose whether you want to receive security updates from Oracle support and if you do, enter your e-mail address.
Click Next.
In the Choose Install Type screen, select Typical and click Next.
In the Choose Product Installation Directories screen, accept the directory ORACLE_BASE/product/fmw/wlserver_10.3. Also accept the default directory for Oracle Coherence (ORACLE_BASE/product/fmw/coherence_3.5).
Click Next.
In the Installation Summary screen, click Next.
The Oracle WebLogic Server software is installed.
In the Installation Complete screen, clear the Run Quickstart option and click Done.
Perform the steps described in this section to install Oracle Business Intelligence on APPHOST1 and APPHOST2. Note that because the installation is performed on a shared storage, the MW_HOME is accessible and used by the Oracle BI servers in APPHOST1 and APPHOST2.
On Linux platforms, if the /etc/oraInst.loc file exists, check that its contents are correct. Specifically, check that the inventory directory is correct and that you have write permissions for that directory. If the /etc/oraInst.loc file does not exist, you can skip this step.
Start the installer for Oracle Business Intelligence from the installation media:
./runInstaller
In the Specify Inventory Directory screen, do the following:
Enter HOME/oraInventory, where HOME is the home directory of the user performing the installation (this is the recommended location).
Enter the OS group for the user performing the installation.
Click Next.
Follow the instructions on screen to execute /createCentralInventory.sh as root.
Click OK.
In the Welcome screen, click Next.
In the Select Installation Type screen, select Software Only Install and click Next.
In the Prerequisite Checks screen, verify that all checks complete successfully, and click Next.
In the Specify Installation Location screen, select the previously installed Middleware home from the drop-down list. For the Oracle home directory, enter the directory name (Oracle_BI1).
Click Next.
In the Specify Security Updates screen, choose whether you want to receive security updates from Oracle support and if you do, enter your e-mail address and click Next.
In the Summary screen, click Install.
The Oracle Business Intelligence software is installed.
In the Installation Progress screen, click Next.
In the Complete screen, click Finish.
At this point, back up the Middleware home. Make sure to stop the servers first.
To back up the Middleware home, run the following command:
APPHOST1> tar -cvpf fmwhomeback.tar ORACLE_BASE/product/fmw
This command creates a backup of the installation files for both Oracle WebLogic Server and the Oracle Fusion Middleware components, including Oracle Business Intelligence.