Skip Navigation Links | |
Exit Print View | |
Oracle Solaris Administration: IP Services Oracle Solaris 11 Information Library |
1. Planning the Network Deployment
2. Considerations When Using IPv6 Addresses
3. Configuring an IPv4 Network
4. Enabling IPv6 on the Network
5. Administering a TCP/IP Network
7. Troubleshooting Network Problems
11. Administering the ISC DHCP Service
12. Configuring and Administering the DHCP Client
13. DHCP Commands and Files (Reference)
14. IP Security Architecture (Overview)
16. IP Security Architecture (Reference)
17. Internet Key Exchange (Overview)
19. Internet Key Exchange (Reference)
20. IP Filter in Oracle Solaris (Overview)
Part IV Networking Performance
22. Integrated Load Balancer Overview
23. Configuration of Integrated Load Balancer (Tasks)
Installing the Integrated Load Balancer
DSR, Full-NAT, and Half-NAT Topologies
Half-NAT Load-Balancing Topology
Full-NAT Load-Balancing Topology
ILB High-Availability Configuration (Active-Passive Mode Only)
ILB HA Configuration Using the DSR Topology
How to Configure ILB to Achieve High-Availability by Using the DSR Topology
ILB High-Availability Configuration by Using the Half-NAT Topology
How to Configure ILB to Achieve High-Availability by Using the Half-NAT Topology
Setting Up User Authorization for ILB Configuration Subcommands
Administering ILB Server Groups
Administering Back-End Servers in ILB
How to Add a Back-End Server to a Server Group
How to Remove a Back-End Server From a Server Group
How to Re-enable or Disable a Back-End Server
Administering Health Checks in ILB
Displaying Health Check Results
Obtaining Statistical Information Using the show-statistics Subcommand
Displaying the NAT Connection Table
Displaying the Session Persistence Mapping Table
Using Import and Export Subcommands
24. Virtual Router Redundancy Protocol (Overview)
25. VRRP Configuration (Tasks)
26. Implementing Congestion Control
Part V IP Quality of Service (IPQoS)
27. Introducing IPQoS (Overview)
28. Planning for an IPQoS-Enabled Network (Tasks)
29. Creating the IPQoS Configuration File (Tasks)
30. Starting and Maintaining IPQoS (Tasks)
31. Using Flow Accounting and Statistics Gathering (Tasks)
This section describes the procedures to enable and disable ILB.
Before You Begin
Make sure that the system's Role Based Access Control (RBAC) attribute files have the following entries (if the entries are not there, add them manually):
File name: /etc/security/auth_attr
solaris.network.ilb.config:::Network ILB Configuration::help=NetworkILBconf.html
solaris.network.ilb.enable:::Network ILB Enable Configuration::help=NetworkILBenable.html
solaris.smf.manage.ilb:::Manage Integrated Load Balancer Service States::help=SmfILBStates.html
File name: /etc/security/prof_attr
Network ILB:::Manage ILB configuration via ilbadm:auths=solaris.network.ilb.config,solaris.network.ilb.enable;help=RtNetILB.html
The Network Management entry in the file should include solaris.smf.manage.ilb.
File name:/etc/user_attr
daemon::::auths=solaris.smf.manage.ilb,solaris.smf.modify.application
You can assign the ILB Management rights profile to a role that you create. To create the role and assign the role to a user, see Initially Configuring RBAC (Task Map) in Oracle Solaris Administration: Security Services.
#ipadm set-prop -p forwarding=on ipv4 # ipadm set-prop -p forwarding=on ipv6
# svcadm enable ilb
# svcs ilb
You can assign the ILB Management rights profile to a role that you create. To create the role and assign the role to a user, see Initially Configuring RBAC (Task Map) in Oracle Solaris Administration: Security Services.
# svcadm disable ilb
# svcs ilb