How NWAM Profiles Are Activated

NCPs, Location profiles, and ENMs have activation-mode properties. The allowable values for each profile type differ. In addition, how the activation-mode property is validated differs for each profile type, as do the conditions under which each profile is activated.

For system-defined locations (Automatic and NoNet), the activation-mode property value is set to system, which means that the location can only be activated by the system, under those conditions that the system has predetermined are appropriate for the given location.

For user-defined locations, you can set the activation-mode and conditions properties to manual, conditional-any, or conditional-all. For more information, see Location Activation Selection Criteria.

A Location profile can be manually enabled by using the netadm command or by using the NWAM GUI. If you do not explicitly enable a location, the NWAM daemon, nwamd, checks the activation rules for all of the conditionally activated and system-activated Location profiles, and then chooses the location that best matches the current network environment.

NWAM uses an algorithm to determine the “best match” for a location choice. If there is no suitable match for a location, the Automatic location is then activated. Changes in the network environment cause the nwamd daemon to continually reassess the location selection to determine the best match. However, if you explicitly enable a Location profile by using the netadm command (either a location that is manually activated or a location that is conditionally activated), that location remains active until you explicitly disable it or enable a different location. In this situation, changes in the network environment do not result in a change in Location profiles, regardless of whether there might be a better match available. The fact that you explicitly specified the current location makes it, in effect, the best possible match. For instructions on activating and deactivating profiles, see Activating and Deactivating Profiles.

NCP Activation Policy

NWAM enables you to specify NCP policy, in terms of when NCUs are activated. The NCP policy is enforced through the use of properties and conditions that can be specified for each NCU. Examples of policies that you might specify include: “prefer wired connections over wireless connections” or “activate one interface at a time.” How and when NCPs are activated is defined in the properties that are set for each NCU type.

Example of an NCP Policy

In the following example, NCU properties are set for when the NCP policy needs to specify that all of the available wired links are activated, and that a wireless connection should only be used if no wired connection is available.

For all physical links:

• NCU type: link

• NCU class: phys

• activation-mode: prioritized

• priority-group: 0 for wired; 1 for wireless

• priority-mode: shared for wired; exclusive for wireless

In the following example, NCU properties are set according to an NCP policy that specifies that there be only one active link on the system at any given time, and that a wired connection is preferred over a wireless connection.

For all physical links:

• NCU type: link

• NCU class: phys

• activation-mode: prioritized

• priority-group: 0 for wired; 1 for wireless

• priority-mode: exclusive

NCU Activation Properties

How network connections are activated is set in the link NCU properties. The following properties are used to define the NCP activation policy:

• activation-mode property

  This property can be set to either manual or prioritized.

  • manual – The NCU activation is managed by the administrator. You can use the NWAM CLI or the GUI to activate or deactivate the NCU. If an NCU's activation-mode is set to manual, values that are set for both the priority-group and priority-mode NCU properties are ignored.

  • prioritized – The NCU is activated according to the values that are set in the priority-group and priority-mode properties for the specified NCU. The enabled property is always true for prioritized NCUs.

    Prioritized activation enables groups of links to be activated at the same time. This activation mode also enables one or more links to be preferred over other links. The priority-group property assigns a numeric priority level to a given link. All links at the same priority level are examined as a group. The priority-mode property defines how many of the group members might or must be available for the group to be activated.

• enabled property ( activation-mode is set to manual)

  The value of this property can be true or false. You cannot set the value of this property. Rather, the value reflects the current state of a manually enabled NCU, which can be changed by using the netadm command or by using the NWAM GUI.

• priority-group property (activation-mode is set to prioritized)

  The value is numeric. Zero (0) indicates the highest priority. Negative values are invalid.

  Among all of the available priority-groups, only the NCUs in the highest available priority-group are activated. When more than one NCU with the same priority is available, activation behavior is defined by the priority-mode property. The priority number is not an absolute value. It can change, as the NCP repository is updated.

  ---

  Note - The priority order is strictly enforced.

  ---

• priority-mode property (activation-mode is set to prioritized)

  The property is set when a value for the priority-group property has been specified.

  The values for this property are as follows:

  • exclusive – Specifies that only one NCU in the priority-group can be active at any given time. NWAM activates the first available NCU within the priority group and ignores the other NCUs.

  • shared – Specifies that multiple NCUs in the priority group can be active at the same time. Any available NCUs in the priority group are activated.

  • all – Specifies that all of the NCUs in the priority group must be made available for the priority group to be considered available and thus made active.

Location Activation Selection Criteria

Each Location profile contains properties that define activation criteria. These properties specify information about the conditions under which a location is activated. NWAM continuously reevaluates the selection criteria for all the configured locations, each time determining which location has the criteria that is the best match for the current network environment. If changes take place in the current network environment that result in a better criteria match, NWAM deactivates the current Location profile and activates the Location profile that is the better match for the new environment.

The selection criteria for when and how a location is activated are specified by the following properties:

• activation-mode

• conditions

The activation-mode property is set to one of the following possible values:

• manual

• conditional-any

• conditional-all

• system

If the activation-mode property is set to conditional-any or conditional-all, the conditions property contains a conditional expression (or expressions) that are user-defined. Each expression contains a condition that can be assigned a boolean value, for example, “ncu ip:net0 is-not active.”

If the activation-mode property is set to conditional-any, the condition is satisfied if any one of the conditions is true.

If the activation-mode property is set to conditional-all, the condition is satisfied only if all of the conditions are true. The criteria and operations that can be used to construct the condition strings are defined in the following table.

Table 3-5 Criteria and Operations for Constructing Condition Strings

Note the distinction between the advertised-domain and the system-domain attributes. The advertised domain is discovered through external communications, for example, the DNSdmain or NISdmain domain names, which are advertised by a DHCP server. This attribute is useful for the conditional activation of locations, for example, if the advertised domain is mycompany.com, then activate the work location. The system-domain attribute is the domain that is currently assigned to the system. It is the value that is returned by the domainname command. This attribute is useful for the conditional activation of ENMs, as it will only become true after a location has been activated, and the system has been configured for that particular domain. For more information, see the domainname(1M) man page.

For more information about location properties, see Description of a Location Profile.