JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Oracle Solaris 11.1 Administration: ZFS File Systems     Oracle Solaris 11.1 Information Library
search filter icon
search icon

Document Information

Preface

1.  Oracle Solaris ZFS File System (Introduction)

2.  Getting Started With Oracle Solaris ZFS

3.  Managing Oracle Solaris ZFS Storage Pools

Components of a ZFS Storage Pool

Using Disks in a ZFS Storage Pool

Using Slices in a ZFS Storage Pool

Using Files in a ZFS Storage Pool

Considerations for ZFS Storage Pools

Replication Features of a ZFS Storage Pool

Mirrored Storage Pool Configuration

RAID-Z Storage Pool Configuration

ZFS Hybrid Storage Pool

Self-Healing Data in a Redundant Configuration

Dynamic Striping in a Storage Pool

Creating and Destroying ZFS Storage Pools

Creating ZFS Storage Pools

Creating a Basic Storage Pool

Creating a Mirrored Storage Pool

Creating a ZFS Root Pool

Creating a RAID-Z Storage Pool

Creating a ZFS Storage Pool With Log Devices

Creating a ZFS Storage Pool With Cache Devices

Cautions For Creating Storage Pools

Displaying Storage Pool Virtual Device Information

Handling ZFS Storage Pool Creation Errors

Detecting In-Use Devices

Mismatched Replication Levels

Doing a Dry Run of Storage Pool Creation

Default Mount Point for Storage Pools

Destroying ZFS Storage Pools

Destroying a Pool With Unavailable Devices

Managing Devices in ZFS Storage Pools

Adding Devices to a Storage Pool

Attaching and Detaching Devices in a Storage Pool

Creating a New Pool By Splitting a Mirrored ZFS Storage Pool

Onlining and Offlining Devices in a Storage Pool

Taking a Device Offline

Bringing a Device Online

Clearing Storage Pool Device Errors

Replacing Devices in a Storage Pool

Designating Hot Spares in Your Storage Pool

Activating and Deactivating Hot Spares in Your Storage Pool

Managing ZFS Storage Pool Properties

Querying ZFS Storage Pool Status

Displaying Information About ZFS Storage Pools

Displaying Information About All Storage Pools or a Specific Pool

Displaying Pool Devices by Physical Locations

Displaying Specific Storage Pool Statistics

Scripting ZFS Storage Pool Output

Displaying ZFS Storage Pool Command History

Viewing I/O Statistics for ZFS Storage Pools

Listing Pool-Wide I/O Statistics

Listing Virtual Device I/O Statistics

Determining the Health Status of ZFS Storage Pools

Basic Storage Pool Health Status

Detailed Health Status

Gathering ZFS Storage Pool Status Information

Migrating ZFS Storage Pools

Preparing for ZFS Storage Pool Migration

Exporting a ZFS Storage Pool

Determining Available Storage Pools to Import

Importing ZFS Storage Pools From Alternate Directories

Importing ZFS Storage Pools

Importing a Pool With a Missing Log Device

Importing a Pool in Read-Only Mode

Importing a Pool By a Specific Device Path

Recovering Destroyed ZFS Storage Pools

Upgrading ZFS Storage Pools

4.  Managing ZFS Root Pool Components

5.  Managing Oracle Solaris ZFS File Systems

6.  Working With Oracle Solaris ZFS Snapshots and Clones

7.  Using ACLs and Attributes to Protect Oracle Solaris ZFS Files

8.  Oracle Solaris ZFS Delegated Administration

9.  Oracle Solaris ZFS Advanced Topics

10.  Oracle Solaris ZFS Troubleshooting and Pool Recovery

11.  Archiving Snapshots and Root Pool Recovery

12.  Recommended Oracle Solaris ZFS Practices

A.  Oracle Solaris ZFS Version Descriptions

Index

Managing ZFS Storage Pool Properties

You can use the zpool get command to display pool property information. For example:

# zpool get all zeepool
NAME     PROPERTY       VALUE                SOURCE
zeepool  allocated      6.29G                -
zeepool  altroot        -                    default
zeepool  autoexpand     off                  default
zeepool  autoreplace    off                  default
zeepool  bootfs         -                    default
zeepool  cachefile      -                    default
zeepool  capacity       1%                   -
zeepool  dedupditto     0                    default
zeepool  dedupratio     1.00x                -
zeepool  delegation     on                   default
zeepool  failmode       wait                 default
zeepool  free           550G                 -
zeepool  guid           7543986419840620672  -
zeepool  health         ONLINE               -
zeepool  listshares     off                  default
zeepool  listsnapshots  off                  default
zeepool  readonly       off                  -
zeepool  size           556G                 -
zeepool  version        34                   default

Storage pool properties can be set with the zpool set command. For example:

# zpool set autoreplace=on zeepool
# zpool get autoreplace zeepool
NAME     PROPERTY     VALUE    SOURCE
zeepool  autoreplace  on       local

If you attempt to set a pool property on a pool that is 100% full, you will see a message similar to the following:

# zpool set autoreplace=on tank
cannot set property for 'tank': out of space

For information on preventing pool space capacity problems, see Chapter 12, Recommended Oracle Solaris ZFS Practices.

Table 3-1 ZFS Pool Property Descriptions

Property Name
Type
Default Value
Description
allocated
String
N/A
Read-only value that identifies the amount of storage space within the pool that has been physically allocated.
altroot
String
off
Identifies an alternate root directory. If set, this directory is prepended to any mount points within the pool. This property can be used when you are examining an unknown pool, if the mount points cannot be trusted, or in an alternate boot environment, where the typical paths are not valid.
autoreplace
Boolean
off
Controls automatic device replacement. If set to off, device replacement must be initiated by using the zpool replace command. If set to on, any new device found in the same physical location as a device that previously belonged to the pool is automatically formatted and replaced. The property abbreviation is replace.
bootfs
Boolean
N/A
Identifies the default bootable file system for the root pool. This property is typically set by the installation programs.
cachefile
String
N/A
Controls where pool configuration information is cached. All pools in the cache are automatically imported when the system boots. However, installation and clustering environments might require this information to be cached in a different location so that pools are not automatically imported. You can set this property to cache pool configuration information in a different location. This information can be imported later by using the zpool import -c command. For most ZFS configurations, this property is not used.
capacity
Number
N/A
Read-only value that identifies the percentage of pool space used.

The property abbreviation is cap.

dedupditto
String
N/A
Sets a threshold, and if the reference count for a deduped block goes above the threshold, another ditto copy of the block is stored automatically.
dedupratio
String
N/A
Read-only deduplication ratio achieved for a pool, expressed as a multiplier.
delegation
Boolean
on
Controls whether a nonprivileged user can be granted access permissions that are defined for a file system. For more information, see Chapter 8, Oracle Solaris ZFS Delegated Administration.
failmode
String
wait
Controls the system behavior if a catastrophic pool failure occurs. This condition is typically a result of a loss of connectivity to the underlying storage device or devices or a failure of all devices within the pool. The behavior of such an event is determined by one of the following values:
  • wait – Blocks all I/O requests to the pool until device connectivity is restored, and the errors are cleared by using the zpool clear command. In this state, I/O operations to the pool are blocked, but read operations might succeed. A pool remains in the wait state until the device issue is resolved.

  • continue – Returns an EIO error to any new write I/O requests, but allows reads to any of the remaining healthy devices. Any write requests that have yet to be committed to disk are blocked. After the device is reconnected or replaced, the errors must be cleared with the zpool clear command.

  • panic – Prints a message to the console and generates a system crash dump.

free
String
N/A
Read-only value that identifies the number of blocks within the pool that are not allocated.
guid
String
N/A
Read-only property that identifies the unique identifier for the pool.
health
String
N/A
Read-only property that identifies the current health of the pool, as either ONLINE, DEGRADED, SUSPENDED, REMOVED, or UNAVAIL.
listshares
String
off
Controls whether share information in this pool is displayed with the zfs list command. The default value is off.
listsnapshots
String
off
Controls whether snapshot information that is associated with this pool is displayed with the zfs list command. If this property is disabled, snapshot information can be displayed with the zfs list -t snapshot command.
readonly
Boolean
off
Identifies whether a pool can be modified. This property is only enabled when a pool is has been imported in read-only mode. If enabled, any synchronous data that exists only in the intent log will not be accessible until the pool is re-imported in read-write mode.
size
Number
N/A
Read-only property that identifies the total size of the storage pool.
version
Number
N/A
Identifies the current on-disk version of the pool. The preferred method of updating pools is with the zpool upgrade command, although this property can be used when a specific version is needed for backwards compatibility. This property can be set to any number between 1 and the current version reported by the zpool upgrade -v command.