A script enabled browser is required for this page to function properly.
Skip to main content
StorageTek Tape Analytics Planning and Installation Guide, Version 1.0.2
E28377-04
Table of Contents Previous Next Index


Pre-Installation Planning : Library Minimum Requirements : Library Hardware Requirements

Library Hardware Requirements

TABLE 2‑5 lists the library hardware requirements for STA.

TABLE 2‑5 Library Hardware Requirements

Library

Component

Requirement

SL8500

HBT card

High memory — For richer drive data to be sent to STA from StorageTek and LTO drives, the library must have a high-memory drive controller (HBT) card. To check the SL Console to determine your HBT card’s level of memory, see the “Verify the Drive Controller Card Version” section of the StorageTek Tape Analytics Configuration Guide.

Note: All SL3000 libraries ship with the high-memory card. From 2006 forward, all SL8500 libraries ship with the high-memory card.

SL150
SL500
SL3000
SL8500

Ethernet connection

Separate connection from STA to each library.

Note: Each library in an SL8500 complex has its own SNMP agent. Therefore, STA must be able to connect to each library separately.

Tape Drive Requirements

The quality of analytics obtained by STA depends on drive capability and its firmware. Some drives can only provide basic information and some cannot provide any information.

LTO drives that support ADI, are configured appropriately, and have supporting firmware can provide STA with high quality data (for example, performance data for drives, and amount and rate of drive utilization).

Note – See “Drive ADI Interface” in the StorageTek Tape Analytics Configuration Guide for information on enabling ADI.

Use the following tables to locate your existing drives and determine whether you need to replace them or upgrade firmware for STA to obtain the best quality data.

Note – For the latest drive firmware supported by STA, open a Service Request (SR) ticket with Oracle Support. Firmware versions are subject to change.

TABLE 2‑6 StorageTek Tape Drive Firmware — Minimum Versions for STA

StorageTek Drive

Minimal/Low Quality Data
TTI 5.10

Higher Quality Data
TTI 5.20

Highest Quality Data
TTI 5.30

T10000A

1.44.108

1.46.109

1.48.112

T10000B

1.44.208

1.46.209

1.48.212

T10000C

N/A

1.51.320

1.53.316

9840C

1.44.510

1.45.503

N/A

9840D

1.44.710

1.45.703

N/A

Note – TTI 5.20 is highly recommended for 9840 drives. TTI 5.30 is highly recommended for T10000 drives.

TABLE 2‑7 Other Vendor Tape Drive Firmware — Minimum Versions for STA 

Vendor

Drive

Supported Firmware

SL8500

SL3000

SL500

SL150

Comments

HP1

LTO 2 LVD SCSI

N/A

x

No support for ADI protocol

LTO 2 FC 2Gb

N/A

x

x

No support for ADI protocol

LTO 3 LVD SCSI

G69S

x

LTO 3 FC 2Gb

L6HS

x

x

x

LTO 3 FC 4Gb

M6BS

x

x

x

LTO 4 LVD SCSI

B57S

x

LTO 4 FC 4Gb

H58S

x

x

x

LTO 5 FH FC 8Gb

I3CS

x

x

x

LTO 5 FH SAS 6Gb

X3AS

x

Requires SL500 Bridged Base Unit

LTO 5 HH FC 8Gb

Y5BS

x

LTO 5 HH SAS 6Gb

Z55S

x

LTO 6 FH FC 8Gb

J2DS

x

x

x

LTO 6 HH FC 8Gb

22GS

x

LTO 6 HH SAS 6Gb

32DS

x

IBM2

LTO 2 LVD SCSI

N/A

x

No support for ADI protocol

LTO 2 FC 2Gb

N/A

x

No support for ADI protocol

LTO 3 FC 2Gb

93G0

x

x

x

LTO 4 FC 2/4Gb

94D7

x

x

x

LTO 4 FC 2/4Gb Encryption

Contact Support

x

x

x

Requires Belisarius card with 4.x.x (minimum) firmware and compatible drive firmware for ADI support.

LTO 5 FC 8Gb

Contact Support

x

x

x

Requires Belisarius card with 4.x.x (minimum) firmware and compatible drive firmware for ADI support.

LTO 6 FC 8Gb

Contact Support

x

x

Requires Belisarius card with 4.x.x (minimum) firmware and compatible drive firmware for ADI support.

Quantum

SDLT 320 LVD SCSI

N/A

x

No support for ADI protocol

SDLT 600 LVD and FC

N/A

x

No support for ADI protocol

S4 LVD and FC

N/A

x

No support for ADI protocol


1

For HP LTO-6 drives, contact Oracle support to obtain the latest supported firmware version.


2

For IBM LTO-3 and LTO-4 drives, an Oracle support representative must configure the drive hardware for ADI mode. For IBM LTO-5 and LTO-6 drives, the drive firmware must be configured for ADI mode — contact Oracle support for assistance.



Table of Contents Previous Next Index Link to documentation
Copyright © 2012, 2013 Oracle and/or its affiliates. All rights reserved.