System Messages: LIBTMIB Catalog 200-299

200

ERROR: Class instance specification is not unique

Description

The specification given for a new or modified class was not unique.

Action

Ensure that the class specification presented to the MIB is unique.

203

ERROR: Unable to mark invalid record for principal principal.

Description

When marking an entry as invalid in the principal file, an error writing the principal file occurred. This error can occur when deleting a principal from the T_ACLPRINCIPAL class. This error usually occurs because of disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

204

ERROR: Could not find principal.

Description

The principal which the T_ACLPRINCIPAL MIB is attempting to delete has already been deleted. This error can only occur if two or more administrators are attempting to delete a principal at the same time.

Action

Make sure that only one person is accessing the ACL MIB at any one time. You can use the MIB to see if the principal in question has been properly removed.

205

ERROR: Unable to append to file filename.

Description

While attempting to open a file, an error occurred. This error happens when using the T_ACLPRINCIPAL class

Action

There are several kernel parameters which could cause this error. Two obvious ones include the maximum allowed size for files and the number of allowable open file descriptors. Disk space could also be a problem. Increase the appropriate kernel parameters or buy a new disk, then try the command again.

207

ERROR: Unable to mark invalid record for principal name.

Description

While modifying a principal in the T_ACLPRINCIPAL class, an error occurred when removing the old principal entry. This error is usually due to disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

212

ERROR: Unable to mark invalid record.

Description

When marking an entry as invalid in the group file, an error writing the group file occurred. This error can occur when deleting a group from the T_ACLGROUP class. This error usually occurs because of disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

213

ERROR: Could not find group.

Description

The group which the T_ACLGROUP MIB is attempting to delete has already been deleted. This error can only occur if two or more administrators are attempting to delete a group at the same time.

Action

Make sure that only one person is accessing the ACL MIB at any one time. You can use the MIB to see if the principal in question has been properly removed.

214

ERROR: Unable to append to file filename.

Description

While attempting to open the given file, an error occurred. This happens when updating the T_ACLGROUP class.

Action

There are several kernel parameters which could cause this error. Two obvious ones include the maximum allowed size for files and the number of allowable open file descriptors. Disk space could also be a problem. Increase the appropriate kernel parameters or buy a new disk, then try the command again.

217

ERROR: Unable to mark invalid record.

Description

When marking an entry as invalid in the group file, an error writing the group file occurred. This error can occur when modifying a group from the T_ACLGROUP class. This error usually occurs because of disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

219

ERROR: Unable to change attributes of the other group.

Description

The other group is a group that always exists and which cannot be altered.

Action

Do not attempt to alter the other group.

220

ERROR: Unable to change state of the other group.

Description

The other group is a group that always exists and which cannot be altered. Hence this group cannot be removed.

Action

Do not attempt to remove the other group.

222

ERROR: Unable to append to file filename.

Description

While attempting to open the given file, an error occurred. This happens when updating the T_ACLPERM class.

Action

There are several kernel parameters which could cause this error. Two obvious ones include the maximum allowed size for files and the number of allowable open file descriptors. Disk space could also be a problem. Increase the appropriate kernel parameters or buy a new disk, then try the command again.

224

ERROR: Unable to mark invalid record.

Description

When marking an entry as invalid in the access file, an error writing the access file occurred. This error can occur when deleting a permission from the T_ACLPERM class. This error usually occurs because of disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

226

ERROR: Unable to find the end of the acl file.

Description

When attempting to find the end of the acl file, an error occurred.

Action

There are several kernel parameters which could cause this error. Two obvious ones include the maximum allowed size for files and the number of allowable open file descriptors. Disk space could also be a problem. Increase the appropriate kernel parameters or buy a new disk, then try the command again.

227

ERROR: Unable to mark invalid record.

Description

When marking an entry as invalid in the access file, an error writing the access file occurred. This error can occur when modifying a permission in the T_ACLPERM class. This error usually occurs because of disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

229

ERROR: Unable to print in the principal file.

Description

While attempting to write into the principal file, an error occurred. This error is usually caused by disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

230

ERROR: Missing key field(s) in /Admin service request

Description

One or more required key fields is missing from an /AdminAPI request. The identifier of the first missing key field is supplied in the TA_BADFLD attribute in the reply buffer.

Action

Using APPQ_MIB(5), determine which key fields are required, then supply the missing field(s).

See Also

MIB(5), APPQ_MIB(5)

231

ERROR: Inappropriate key field(s) for /Admin service request for unconfigured application

Description

The TA_LMID attribute was specified in an /AdminAPI request for a T_APPQ, T_APPQMSG, T_APPQSPACE, or T_APPQTRANS object but the application is not configured (i.e., the TUXCONFIG environment variable is not defined). Because the application is not configured, there are no known logical machine identifiers, and specifying the TA_LMID attribute is inappropriate.

Action

Resubmit the /AdminAPI request, but omit the TA_LMID attribute from the request.

See Also

MIB(5), APPQ_MIB(5)

232

ERROR: TA_MIN is greater than TA_MAX

Description

A SET operation on a T_SERVER class object set the TA_MIN value greater than the new, existing, or default TA_MAX value.

Action

Correct the values of TA_MIN and/or TA_MAX and re-try the operation.

See Also

MIB(5), TM_MIB(5)

233

ERROR: TA_SRVID plus TA_MAX yields server identifier greater than 30,000

Description

A SET operation on a T_SERVER class object set the TA_SRVID and TA_MAX values such that their sum is greater than 30,000. Server identifiers must be less than or equal to 30,000.

Action

Correct the values of TA_SRVID and/or TA_MAX and re-try the operation.

See Also

MIB(5), TM_MIB(5)

234

ERROR: TA_LMID value does not match local machine

Description

The TA_LMID value specified on an /AdminAPI SET request for a T_DEVICE object does not match the configured logical machine identifier for the local machine.

Action

Correct the /AdminAPI request to use the local logical machine identifier.

See Also

MIB(5), TM_MIB(5)

235

INFO: .SysResourceConfig: system configuration change

Description

This message indicates that parameters in the T_DOMAIN class have been updated. A complete listing of the current parameters are sent along in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

236

ERROR: SET operation did not specify required key field

Description

If a class contains any key fields necessary for a SET, then at least one of these fields must be present in a the SET buffer. This requirement protects against the case of a class which has one and only one instance, and the SET buffer contains no fields at all (matching the one instance). This one instance may or may not be a proper match for the required action.

Action

Add one of the required SET keys to the input buffer such that the SET keys match one and only one instance of the class. Rerun the request against the MIB.

237

ERROR: Unable to add to the access control file.

Description

When modifying the T_ACLPERM class, an error occurred when writing the access control list file. This error is usually caused by disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

240

INFO: .SysMachineConfig: LMID configuration change

Description

This message indicates that parameters in the T_MACHINE class for the given LMID have been updated. A complete listing of the current parameters for the given LMID are sent along in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

243

ERROR: TA_LMID value does not match local machine

Description

The TA_LMID value specified on an /AdminAPI SET request for a T_APPQ, T_APPQMSG, T_APPQSPACE, or T_APPQTRANS object does not match the configured logical machine identifier for the local machine.

Action

Resubmit the /AdminAPI request and use the correct logical machine identifier.

See Also

MIB(5), APPQ_MIB(5)

245

ERROR: There are no more valid group identifiers

Description

Group identifiers can only be in the range 0 through 16383. If all group identifiers have been used, then it is impossible to add a new group to the system.

Action

Remove a group, then add a new group.

246

ERROR: There are no more valid user identifiers

Description

User identifiers can only be in the range 1 through 131,071. If all user identifiers have been used, then it is impossible to add a new user to the system.

Action

Remove a user, then add a new user.

248

INFO: .SysMachineState: LMID state change to state

Description

This message states that the specified machine changed to a new state as mentioned in the message. A complete listing of the current parameters are sent along in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

249

INFO: .SysServerConfig: servername, group srvgrp, id srvid configuration change

Description

This message indicates that the configuration parameters for the server specified above have been updated. A complete listing of the attributes of the server are sent along in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

250

INFO: .SysServerState: servername, group srvgrp, id srvid state change to state

Description

This message indicates that the server specified above changed to a new state. A complete listing of the server attributes are sent in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

251

INFO: .SysClientState: User usrname on LMID state change to state

Description

This message indicates that the client specified above changed to a new state. A complete listing of the current attributes of the client are sent in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

252

INFO: .SysGroupState: Group groupname on lmid state change to state

Description

This message indicates that the group specified above changed to a new state. A complete listing of the group attributes are sent in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

253

INFO: .SysClientConfig: User usrname on LMID configuration change

Description

This message indicates that the attributes on the client specified above have been changed. A complete listing of the current attributes of the client are sent in the posted buffer.

Action

This is an informational message.

See Also

EVENT_MIB(5), TM_MIB(5)

254

ERROR: Required field not present on SET request

Description

The field indicated by TA_BADFLD is required for the current /AdminAPI request and was not present.

Action

Regenerate the request using an appropriate value for the indicated field.

See Also

MIB(5), TM_MIB(5)

255

ERROR: Class only valid on security levels greater than APP_PW.

Description

This class is only valid if the security level in the ubbconfig(5) is set to USER_AUTH, ACL, or MANDATORY_ACL.

Action

Change the SECURITY level in your ubbconfig(5) to USER_AUTH, ACL, or MANDATORY_ACL. Then run tmloadcf(1) on your new ubbconfig file.

256

ERROR: Unable to seek in group file.

Description

While attempting to manipulate the file position indicator in the group file, an error occurred. This error is usually caused by disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

257

ERROR: Unable to print in group file.

Description

While attempting to write into the group file, an error occurred. This error is usually caused by disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

258

ERROR: Unable to seek in principal file.

Description

While attempting to manipulate the file position indicator in the principal file, an error occurred. This error is usually caused by disk corruption.

Action

Run a diagnostic on the disk to see whether the disk is corrupted. If it is corrupted, buy a new disk and run the command again. If it is not, then contact Oracle TUXEDO system Technical Support.

260

ERROR: Cannot create NEW T_DOMAIN in MP/LAN mode without networking information

Description

A SET TA_STATE NEW /AdminAPI request on the T_DOMAIN class attempted to create a networked application (MP model, LAN option) without specifying required networking addresses.

Action

Regenerate the request specifying the required networking addresses.

See Also

MIB(5), TM_MIB(5)

261

ERROR: Inconsistent user attributes detected.

Description

While looking at the access control cache an inconsistent entry was found in the shared memory.

Action

If this error happens consistently, contact your Oracle TUXEDO system Technical Support.

262

ERROR: T_WSL creation conflicts with existing server

Description

An attempt was made to create a T_WSL object which already exists with the MIB. The TA_SRVGRP and TA_SRVID of the new object match an existing object.

Action

Change the TA_SRVGRP or TA_SRVID attributes of the new WSL, so that it does not clash with an existing server or T_WSL object.

263

ERROR: Server group name does not match existing group

Description

While attempting to create a new service group, the TA_SRVGRP field did not match an existing server group,

Action

The TA_SRVGRP field must match an existing server group upon creation of a service group. Either create the missing server group before attempting to create the service group, or change the TA_SRVGRP field to match and existing server group.

264

INFO: Restarting server at alternate location

Description

A server has been migrated to a new location

Action

None.

265

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process during a pclean operation.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full. If it seems that there should be enough file descriptors and disk space for this operation, contact your Oracle TUXEDO system Technical Support.

266

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process during a pclean operation.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

267

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while setting a server state to DEAD.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

268

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while setting a server state to DEAD.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

269

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while setting a server group state to INACTIVE.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

270

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while setting a server group state to INACTIVE.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

271

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while migrating a group.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

272

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while migrating a group.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

273

ERROR: sbblrtn could not send reply error-core

Description

The sbbl process could not send a reply to the requestor.

Action

The code in error-code may provide clues as to the cause of this problem.

274

ERROR: Failed to get information on the migrating server group

Description

A tpcall to the MIB from the sbbl process did not complete successfully.

Action

Check the log for related messages.

275

ERROR: Failed to get information on the service group

Description

A tpcall to the MIB from the sbbl process did not complete successfully.

Action

Check the log for related messages.

276

ERROR: TA_MINENCRYPTBITS(min) must be less than or equal to TA_MAXENCRYPTBITS(max)

Description

An attempt has been made to change the TA_MINENCRYPTBITS field in the T_WSL class to a value greater than TA_MAXENCRYPTBITS.

Action

The value of min must be less than or equal to the value of max. Change the MIB request to comply with this requirement. You may need to change the command line options -z or -Z on the CLOPT line of your WSL process.

277

ERROR: TA_MINENCRYPTBITS(min) must be less than or equal to TA_MAXENCRYPTBITS(max)

Description

An attempt has been made to change the TA_MINENCRYPTBITS field in the T_MACHINE class to a value greater than TA_MAXENCRYPTBITS.

Action

The value of min must be less than or equal to the value of max. Change the MIB request to comply with this requirement. You may need to change the value of MINENCRYPTBITS or MAXENCRYPTBITS in your ubbconfig file.

278

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while getting information from an application queue space.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

279

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while getting information from an application queue space.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

280

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while getting information from an application queue.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

281

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while getting information from an application queue.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

282

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while getting information about a message on an application queue.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

283

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while getting information about a message on an application queue.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

284

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while getting information about a transaction on an application queue.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

285

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while getting information about a transaction on an application queue.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

286

ERROR: Cannot open file

Description

The MIB has failed to open a file to pass to the sbbl process while setting information about an application queue.

Action

If the host operating system has a limit on the number of open files, or the number of open files per user or the number of open files per process, then you may need to increase that limit. The file system /tmp may be full. The directory where temporary files are placed may be full.

287

ERROR: Cannot write to file

Description

The MIB has failed to write to a file for the sbbl process while setting information about an application queue.

Action

The file system /tmp may be full. The directory where temporary files are placed may be full.

288

ERROR: can't SET Internet type of network address(es).

Description

Internet addresses cannot be used in a configuration which contains releases older than the Oracle TUXEDO system 6.3 release.

Action

Since older sites cannot properly interpret internet addresses, internet addresses cannot be used when interoperating with a release of the Oracle TUXEDO system older than 6.3. Change the address in the MIB request packet to conform to the older style of network addressing.

289

ERROR: Unable to determine license level

Description

An attempt to determine the license information for the Oracle TUXEDO system failed.

Action

Check the log for related messages. Ensure that the Oracle TUXEDO system has been properly installed and licensed.

290

ERROR: SET operation is not allowed on ADMGRP server

Description

An attempt was made to perform a SET operation on a T_SERVER class object which has TA_GRPNO larger than 30,000.

Action

No action required.

See Also

TM_MIB(5)

291

ERROR: Cannot change own state to DEAD

Description

A SET operation on a T_CLIENT class object changing the TA_STATE of the object to DEAD failed because the client id of the requesting client was equal to the client id of the client to be killed.

Action

Make sure that the client id you specify is not your own.

292

ERROR: Cannot change own state to SUSPENDED

Description

A SET operation on a T_CLIENT class object changing the TA_STATE of the object to SUSPENDED failed because the client id of the requesting client was equal to the client id of the client to be suspended.

Action

Make sure that the client id you specify is not your own.

293

ERROR: Cannot invalidate T_NETGROUP class instance with network mappings

Description

The specified NETGROUP was still used entries in the Network section.

Action

The NETWORK entries using this NETGROUP must be removed before the NETGROUP.

See Also

TM_MIB(5)

294

ERROR: TA_NETGRPNO may not be changed because of active network mappings to group

Description

Dynamically changing the NETGROUPS while the machines are running is not permitted.

Action

Dynamically changing the NETGROUPS while the machines are running is not permitted.

See Also

TM_MIB(5)

295

ERROR: TA_NETGROUP or TA_NETGRPNO not unique

Description

The administrator must identify each NETGROUP name with a unique NETGROUPNO number.

Action

Choose a different NETGROUP name or NETGROUPNO number that does not conflict with an existing ones before repeating the operation.

See Also

TM_MIB(5)

296

ERROR: T_NETGROUP class instance cannot be added, table full

Description

The *NETGROUPS table is full, there is no room for the new entry.

Action

Increase MAXNETGROUPS before inserting again, this parameter must be adjusted when the system is shut down.

See Also

TM_MIB(5)

297

ERROR: A network mapping cannot be created for a non existant network group

Description

The NETGROUP used in this NETWORK section entry has not been created yet.

Action

Create NETGROUP before repeating the operation.

See Also

TM_MIB(5)

298

ERROR: A network mapping cannot be created for a non existant LMID

Description

The LMID must be created before this network mapping.

Action

The LMID must be created before this network mapping.

See Also

TM_MIB(5)

299

ERROR: Cannot invalidate the DEFAULTNET T_NETGROUP class

Description

The reserved DEFAULTNET group may not be removed.

Action

The reserved DEFAULTNET group may not be removed.

See Also

TM_MIB(5)