This chapter describes the tasks to perform when configuring X2-4 and X3-4 Exalytics Machines for virtualization. The tasks include deploying Oracle Virtual Machine Server (Oracle VM Server) on the Exalytics Machine, configuring Oracle VM Server with Oracle Virtual Machine Manager (Oracle VM Manager), and deploying VM templates.
This chapter includes the following sections:
Section 2.2, "Configuring an Exalytics Machine for Virtualization"
Section 2.3, "Installing and Configuring Exalytics Software on Virtual Machines"
Before you virtualize an Exalytics Machine, review the following sections:
Section 2.1.2, "Prerequisites for Configuring Exalytics Machines for Virtualization"
Section 2.1.4, "Reconfiguring Existing RAID Configurations on the Exalytics Machine"
As you prepare to virtualize an Exalytics Machine, do the following:
Review the Oracle VM Release Notes, to ensure that you understand the differences between Oracle Virtual Machine and its documented functionality, and any other issues that apply to the current release.
Review Oracle VM Installation and Upgrade Guide for Release 3.2.1 and Oracle VM User's Guide for Release 3.2.1 to ensure that you understand how to install and configure Oracle Virtual Machine Server, set up networking, and create virtual machines.
Review Oracle Exalytics In-Memory Machine Owner's Guide to ensure that you have properly configured and commissioned the Exalytics Machine in your data center.
The following prerequisites must be met before you can virtualize an Exalytics Machine:
The new Exalytics Machine has been racked and mounted in a data center.
Oracle Integrated Lights Out Manager (ILOM) 3.1.2.24 or later, is configured to be accessible from the network using the web interface.
All networking information such as host name, IP address, subnet, gateway, and DNS are available.
Spare, unassigned IP addresses are available for the server pool and for each virtual machine deployed on the Exalytics Machine.
A Linux environment is available to install Oracle VM Manager.
A database server is available to install Oracle VM Manager schemas.
You have access to the internet from a computer (not necessarily the Exalytics Machine) to download required software.
For information about hardware and software specifications, see Oracle VM Installation and Upgrade Guide for Release 3.2.1.
If required, remove the existing partition on /dev/sdb which is mounted to /u01 from the Exalytics Machine. You cannot create a repository on a Oracle Virtual Machine disk which contains a partition.
Note:
Before removing the existing partition, remember to back up all data on sdb1.
To remove existing partitions:
Log in as the root user, and enter the following command to run the disk partition utility:
# parted /dev/sdb
The output should look similar to the following:
GNU Parted 1.8.1 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands.
To display the existing partition, enter the following command:
# print
To remove the existing partition, enter the following command:
# rm 1
To confirm that the existing partition has been removed, enter the following command:
# print
The existing partition is removed.
This sections consists of the following topics:
Section 2.1.4.1, "Reconfiguring Existing RAID Configurations on the X2-4 Exalytics Machine"
Section 2.1.4.2, "Reconfiguring Existing RAID Configurations on the X3-4 Exalytics Machine"
The X2-4 Exalytics Machine comprises six hard disks, each having a capacity of 600GB. Two disks are configured as RAID1 and four disks are configured as RAID5. To optimize the use of the disk space, you must reconfigure the RAID1 and RAID5 configurations on the Exalytics Machine. Reconfigure RAID1 so that it consists of two virtual drives of 100GB and 457GB, and RAID5 consists of the remaining drives.
To reconfigure existing RAID configurations on the X2-4 Exalytics Machine:
Restart the Exalytics Machine using Integrated Lights Out Manager (ILOM).
Press Ctrl+Y and enter RAID CLI (Command Line Interface) as the Exalytics Machine is restarting.
Note:
The "Copyright LSI Logic Corporation" displays during the restart sequence when it is possible to enter the RAID CLI. Observe the screen carefully as the message displays for a very short time. This avoids restarting the machine again.
Enter the following MegaRAID command to delete the existing RAID configuration:
# -CfgLdDel -LALL -a0
Enter the following command to create a RAID1 partition with two virtual disks of size 100GB and 457GB:
# -CfgLdAdd -r1[252:0, 252:1] WB Direct NoCachedBadBBU -sz102400 -sz467968 -a0
Enter the following command to create a RAID5 partition with the remaining disks:
# -CfgLdAdd -r5[252:2, 252:3, 252:4, 252:5] WB Direct NoCachedBadBBU -a0
In ILOM, select ILOM, then Host Management, and then Power Cycle.
The Exalytics Machine restarts.
The X3-4 Exalytics Machine comprises 6 hard disks, each having a capacity of 900 GB. Two disks are configured as RAID1 and four disks are configured as RAID5. To optimize the use of the disk space, you must reconfigure the RAID1 and RAID5 configurations on the Exalytics Machine. Reconfigure RAID1 so that it consists of two virtual drives of 100GB and 657GB, and RAID5 consists of the remaining drives.
To reconfigure existing RAID configurations on the X3-4 Exalytics Machine:
Restart the Exalytics Machine using Integrated Lights Out Manager (ILOM).
Press Ctrl+Y and enter RAID CLI (Command Line Interface) as the Exalytics Machine is restarting.
Note:
The "Copyright LSI Logic Corporation" displays during the restart sequence when it is possible to enter the RAID CLI. Observe the screen carefully as the message displays for a very short time. This avoids restarting the machine again.
Enter the following MegaRAID command to delete the existing RAID configuration:
# -CfgLdDel -LALL -a0
Enter the following command to create a RAID1 partition with two virtual disks of size 100GB and 657 GB:
# -CfgLdAdd -r1[252:0, 252:1] WB Direct NoCachedBadBBU -sz102400 -sz672768 -a0
Enter the following command to create a RAID5 partition with the remaining disks:
# -CfgLdAdd -r5[252:2, 252:3, 252:4, 252:5] WB Direct NoCachedBadBBU -a0
In ILOM, select ILOM, then Host Management, and then Power Cycle.
The Exalytics Machine restarts.
If you are on a virtual Exalytics deployment and want to revert back to a nonvirtual Exalytics deployment, you must reset the RAID configuration by performing the following steps:
To reset RAID configuration:
Restart the Exalytics Machine using Integrated Lights Out Manager (ILOM).
Press Ctrl+Y and enter RAID CLI (Command Line Interface) as the Exalytics Machine is restarting.
Note:
The "Copyright LSI Logic Corporation" displays during the restart sequence when it is possible to enter the RAID CLI. Observe the screen carefully as the message displays for a very short time. This avoids restarting the machine again.
Enter the following MegaRAID command to delete the existing RAID configuration:
# -CfgLdDel -LALL -a0
Enter the following command to restore the RAID1 partition to an Exalytics deployment:
# -CfgLdAdd -r1[252:0, 252:1] WB Direct NoCachedBadBBU -a0
Enter the following command to create a RAID5 partition with the remaining disks:
# -CfgLdAdd -r5[252:2, 252:3, 252:4, 252:5] WB Direct NoCachedBadBBU -a0
In ILOM, select ILOM, then Host Management, and then Power Cycle.
The Exalytics Machine restarts.
This section includes the following topics:
Section 2.2.1, "Installing and Configuring Oracle VM Server"
Section 2.2.2, "Installing and Configuring Oracle VM Manager 3.2.4"
Oracle VM Server is a managed virtualization environment providing a secure, server-based platform for running virtual machines. Before you can create a virtual machine you must first install Oracle VM Server on the Exalytics Machine.
This section includes the following topics:
If you are an existing customer running Oracle VM Server 3.0.3, you can upgrade to Oracle VM Server 3.2.4. For instructions, see Section 7.4.4.2.2, "Upgrading Oracle Exalytics for Oracle VM 3.0.3 to Oracle VM 3.2.4."
If you are a new customer, you must install and configure Oracle VM Server 3.0.3 before you can upgrade to Oracle VM Server 3.2.4.
This section includes the following topics:
Section 2.2.1.2.1, "Installing Oracle VM Server 3.0.3 (Base Image 2.0.1.1)"
Section 2.2.1.2.2, "Configuring the Network on Oracle VM Server"
Section 2.2.1.2.3, "Upgrading Oracle VM Server 3.0.3 to Oracle VM Server 3.2.4"
To install Oracle VM Server 3.0.3:
Download and save the Oracle Exalytics Base Image 2.0.1.1.0 for Exalytics Oracle VM x86-64 (Part Number V34491-01), by performing the following steps:
Navigate to the Oracle Software Delivery Cloud web site at the following link:
In the Select a Product Pack list, select Oracle Business Intelligence.
In the Platform list, select Linux X86-64.
Click Go.
Select Oracle Exalytics Software Media Pack for Linux x86-64 Release: 1.0.0.3.0.
Click Continue.
Download Oracle Exalytics Base Image 2.0.1.1.0 for Exalytics Oracle VM x86-64 Part Number: V34491-01.
The base image contains the Oracle VM Server 3.0.3.
Save it to a local directory.
On the Exalytics Machine, connect and log on to Oracle Integrated Lights Out Manager (ILOM).
In ILOM, select Remote Control, then Redirection, then Storage Redirection, and then Launch Service.
The ILOM remote console is displayed.
From the menu bar, select Devices and then CD-ROM Image to link the Oracle VM Server image as a remote virtual CD-ROM in ILOM.
Perform the following action to restart the machine:
In ILOM, select ILOM, then Host Management, and then Power Cycle.
In ILOM, select Host Management, then Host Control, and then Next Boot Device.
The setting for the Next Boot Device is displayed.
Perform the following steps to move CD-ROM to the top of the BOOT menu:
In the Next Boot Device list, select CD-ROM.
Click Save.
In ILOM, select ILOM, then Host Management, and then Power Cycle.
The Exalytics Machine restarts and displays the Oracle VM Server screen.
Press Enter to install Oracle VM Server.
The Oracle VM Server is installed on the Exalytics Machine. After Oracle VM Server is installed, the Exalytics Machine restarts automatically.
From the menu bar, select Devices, and then deselect CD-ROM Image.
From the menu bar, select Devices, and then Save as host defaults.
In ILOM, select ILOM, then Host Management, and then Power Cycle.
The Exalytics Machine is ready for configuration.
Log on to Oracle VM Server, and enter the following command to inspect the RAID configuration:
/opt/MegaRAID/MegaCli/MegaCli64 -LDinfo -LALL -aALL
Before configuring the network, ensure that the Exalytics network configuration is complete.
To configure the network on Oracle VM Server:
After the Exalytics Machine restarts, perform the following actions:
Enter "I" to access the interactive mode.
At the prompt, enter the following information:
Enter 3 for Full Rack and confirm your entry.
Enter 1 for Node Index.
Enter an IP address for the Infiniband interface. If the Infiniband is not configured, enter a network configuration that does not conflict with existing networks. For example, enter 192.168.21.112.
Enter a netmask address for the Infiniband interface. If the Infiniband is not configured, enter a network configuration that does not conflict with existing networks. For example, enter 255.255.255.0.
Enter the system IP address for the ethernet bond0.
Enter the bond0 netmask and gateway addresses.
Enter the host name.
Enter the domain.
The Exalytics Machine restarts automatically.
To upgrade Oracle VM Server 3.0.3 to Oracle VM Server 3.2.4, see Section 7.4.4.2.2, "Upgrading Oracle Exalytics for Oracle VM 3.0.3 to Oracle VM 3.2.4."
If required, pin or bind Dom0 CPU.
To pin Dom0 CPU:
Navigate to the /etc/xen directory.
Edit the file xend-config.sxp to set the following:
(dom0-cpus 10)
Restart the Exalytics Machine.
Oracle VM Manager provides a graphical user interface to manage Oracle VM Servers, virtual machines, and resources. You use Oracle VM Manager to create virtual machines and server pools, import VM templates, and manage networks and storage.
This section includes the following sections:
If you are an existing customer running Oracle VM Manager 3.0.3, you can upgrade to Oracle VM Manager 3.2.4. For instructions, see Section 7.4.4.2.2, "Upgrading Oracle Exalytics for Oracle VM 3.0.3 to Oracle VM 3.2.4."
If you are a new customer, you must first install Oracle VM Manager 3.2.1 and then upgrade to Oracle VM Manager 3.2.4.
This section includes the following topics:
Section 2.2.2.2.2, "Upgrading Oracle VM Manager 3.2.1 to Oracle VM Manager 3.2.4"
Section 2.2.2.2.4, "Creating Virtual Network Interface Controllers"
Section 2.2.2.2.5, "Creating Server Pools and Adding a Server"
Oracle recommends that you install Oracle VM Manager on a separate machine than the Exalytics Machine, preferably colocated geographically within Oracle VM Server.
Note:
Oracle also recommends that you use the same release version of Oracle VM Manager and Oracle VM Server.
To install Oracle VM Manager 3.2.1:
Download Oracle VM Manager 3.2.1 (Part Number V36286-01) from the Oracle Software Delivery Cloud web site at the following link:
Install Oracle VM Manager 3.2.1. For instructions, see Chapter 4, "Installing Oracle VM Manager" in Oracle VM Installation and Upgrade Guide for Release 3.2.1.
To upgrade Oracle VM Manager 3.2.1 to Oracle VM Manager 3.2.4 (or a later release version in the Oracle VM Manager 3.2.x series) navigate to My Oracle Support, download patch number 16410417, and follow the readme instructions for upgrading Oracle VM Manager.
Adding Oracle VM Servers to your Oracle VM Manager environment is known as discovering Oracle VM Servers. Discovering servers is the first step to configuring the virtualization environment.
To discover Oracle VM Servers:
Connect to Oracle VM Manager.
Select the Servers and VMs tab.
In the left pane, right-click Server Pools, and then select Discover Servers.
The Discover Dialog box is displayed.
Enter the following information for the server:
Oracle VM Agent Port. The default port number is 8899.
Oracle VM Agent Password. The default password is "oracle".
IP Address.
Click OK.
Oracle VM Server and its details, including number of processors, IP address, processor speed, RAM, networking ports and configuration are discovered and added to the Unassigned Servers folder.
For more information, see "Chapter 6, Server Pools" in Oracle VM User's Guide for Release 3.2.1.
A Virtual Network Interface Controller (VNIC) is used by virtual machines as network cards. You create virtual network interfaces by defining a range of MAC addresses to use for each VNIC. Each MAC address corresponds with a single virtual Network Interface Controller (NIC), which is used by a virtual machine.
To create Virtual Network Interface Controllers:
Log on to Oracle VM Manager.
Select the Servers and VMs tab.
In the left pane, right-click Server Pools, and then select Create VNICs.
The MAC selector panel is displayed.
Click Next to retrieve the next available MAC addresses.
Select the number of addresses that you want to create, and click Create.
Note:
Select the number of addresses that corresponds to the number of virtual machines you are deploying.
The VNICs are created and listed in the Virtual NIC table.
Click Close.
For more information, see "Chapter 7, Managing Virtual Machines" in Oracle VM User's Guide for Release 3.2.1.
A server pool consists of at least one Oracle VM Server. If you find a server pool does not have sufficient resources, such as CPU or memory, to run the virtual machines, you can expand the server pool by adding more Oracle VM Servers.
Before creating a server pool, you must have:
An IP address for the server pool
An IP address for each virtual machine
The password to access the Oracle VM Agent installed on Oracle VM Server
For information on creating server pools and adding servers, see "Chapter 6, Server Pools" in Oracle VM User's Guide for Release 3.2.1.
Note:
When creating a server pool, you must deselect the Activate Cluster option.
A repository stores Oracle VM resources, such as virtual machines, templates for creating virtual machines, virtual machine assemblies, and so on.
Note:
Oracle recommends that you create a repository on each physical disk available. Use the smaller repository to store Oracle VM templates and cloned virtual machines and the larger repository to store virtual disks that are assigned to the virtual machines.
You use Oracle VM Manager to create and configure Exalytics repositories, and to present the repositories to Oracle VM Servers.
To create an Exalytics repository:
Log on to Oracle VM Manager.
Select the Repositories tab.
In the toolbar, click Create New Repository to display the Create a Data Repository dialog.
Perform the following actions:
In the Repository Name field, enter the name for the repository.
For Repository Location, select Physical Disk and click Search.
From the drop-down list, select a local storage array and select the smaller of the two storage disks.
Click OK.
Select the server pool for the repository.
Click Next.
The new repository is available to be presented to Oracle VM Server. To enable your Oracle VM Server to use the repository, you must present the repository to Oracle VM Server.
Select and move Oracle VM Server from the Servers field to the Present to Server(s) field and click Finish.
The repository is listed in the Repository tab.
For more information, see "Chapter 4, Managing Storage" in Oracle VM User's Guide for Release 3.2.1.
You use virtual templates to create virtual machines. The process of creating a virtual machine from a template is known as cloning. Before you create virtual machines, ensure that you have the following resources available:
A server pool
An Oracle VM Server
VM templates
The process of creating virtual machines from templates consists of the following steps:
Section 2.2.3.2, "Importing VM Templates into Oracle VM Manager"
Section 2.2.3.3, "Creating Virtual Machines from VM Templates"
To download VM templates:
Download and save the Exalytics Oracle VM Template 2.0.1.1.0 for Exalytics Oracle VM x86-64, by performing the following steps:
Navigate to the Oracle Software Delivery Cloud web site at the following link:
In the Select a Product Pack list, select Oracle Business Intelligence.
In the Platform list, select Linux X86-64.
Click Go.
Select Oracle Exalytics Software Media Pack for Linux x86-64 Release: 1.0.0.3.0.
Click Continue.
Download the Oracle Exalytics Oracle VM Template 2.0.1.1.0 for Exalytics Oracle VM x86-64, Part Number: V34468-01.
Save it on a web server.
After downloading the templates, you import them into Oracle VM Manager.
To import VM templates into Oracle VM Manager:
Log on to Oracle VM Manager.
Select the Repositories tab.
In the left pane, select the Repository in which you want to store the template.
Select VM Templates .
In the toolbar, click Import VM Template to display the Import VM Template dialog.
Select the Oracle VM Server and enter the URL or FTP server to the VM template that you downloaded on the web server.
Click OK to import the VM template.
After importing the template in Oracle VM Manager, you use the template to create a virtual machine.
Note:
Oracle recommends that you use Oracle VM Manager to create virtual disks of the sizes required for your system on the larger repository. Associate these virtual disks with the virtual machines deployed on your system. These virtual disks provide enough storage for installing the Exalytics software and the various files associated with the Exalytics Machine.
To create virtual machines from a VM template:
Log on to Oracle VM Manager.
Select the Servers and VMs tab.
In the left pane toolbar, click Create Virtual Machine.
The Create Virtual Machine dialog is displayed.
Select Clone from an existing VM Template.
Perform the following actions:
In the Clone Count list, select the number of machines you want to clone.
In the Repository list, select a repository for the machine.
In the VM Template list, select the VM template from which you want to create the virtual machine.
Enter a name for the virtual machine.
In the Server Pool list, select a server pool.
Enter a description for the virtual machine.
Click Finish.
The virtual machine is created and is ready to be configured.
For more information, see "Chapter 7, Managing Virtual Machines" in Oracle VM User's Guide for Release 3.2.1.
This section includes the following topics:
Section 2.2.4.1, "Viewing Virtual Machine Information and Events"
Section 2.2.4.2, "Configuring and Starting a Virtual Machine"
Section 2.2.4.3, "Configuring a Network on a Virtual Machine"
You can view virtual machine details and jobs associated with the virtual machine.
To view virtual machine information details:
Log on to Oracle VM Manager.
Select the Servers and VMs tab.
In the left pane, select the server pool on which the virtual machine resides.
From the Perspective list, select Virtual Machines.
In the Management pane, select a virtual machine.
Click the expand arrow to the left of the selected virtual machine.
The following tabs are displayed:
Configuration: Displays general information about the virtual machine, such as the minimum and maximum memory and processors, operating system, domain type, high availability status, and so on.
Networks: Displays networks and VNICs used in the virtual machine.
Disks: Displays virtual and physical disks attached to the virtual machine.
To view virtual machine events:
Log on to Oracle VM Manager.
Select the Servers and VMs tab.
In the left pane, select the server pool on which the virtual machine resides.
From the Perspective list, select Virtual Machines.
In the Management pane, select a virtual machine.
In the toolbar, click Display Selected VM Events.
The Events dialog is displayed.
Review the jobs associated with the virtual machine.
For more information, see "Chapter 7, Managing Virtual Machines" in Oracle VM User's Guide for Release 3.2.1.
You start a virtual machine from Oracle VM Manager.
To configure and start a virtual machine:
Log on to Oracle VM Manager.
Select the Servers and VMs tab.
In the left pane, select the server pool on which the virtual machine resides.
From the Perspective list, select Virtual Machines.
In the Management pane, select a virtual machine, and from the toolbar click the Edit.
The Edit Virtual Machine dialog is displayed.
Select the Configuration tab.
Select the necessary configuration for the virtual machine, and click OK.
Select the Networks tab.
Select and assign a VNIC to the virtual machine, and click OK.
Select the Disks tab.
Select and allocate the virtual disk to the virtual machine.
Click OK.
From the toolbar, click Start.
The virtual machine starts.
For more information, see "Chapter 7, Managing Virtual Machines" in Oracle VM User's Guide for Release 3.2.1.
After starting a virtual machine, you then configure the network on the virtual machine to enable it to access the network.
To configure a network on the virtual machine:
Log on to Oracle VM Server.
Enter the following command:
xm list
The Domain-0 and UUID number for the virtual machine are displayed.
Execute the following command:
xm console <UUID_NUMBER_FOR_VIRTUAL_MACHINE>
The console of the virtual machine is displayed.
Log in as root user with default password "ovsroot".
Enter the following command:
system-config-network
Edit the eth0 device by entering the following information:
IP addresses
Netmask
Gateway
DNS settings
Click Save and Quit.
Run the following command to reload the network configuration:
service network reload
Edit the /etc/hosts file to add the machine name and IP address.
When the virtual machine first restarts, it may not have the swap correctly configured. If needed, configure the swap correctly.
To configure SWAP on the virtual machine:
Ensure that the last line of the file /etc/fstab reads as follows:
LABEL=SWAP-VM swap swap defaults 0 0
If the first entry in the file /etc/fstab reads as LABEL=SWAP-hda3, edit the file to read as:
LABEL=SWAP-VM
To make the swap device available, run the following command:
swapon-a
To confirm that swap is configured, run the following command:
swapon-s
The process of installing Exalytics software on virtual machines is identical to installing the software on the Exalytics Machine, except that the virtual machines cannot access the entire Exalytics memory. Keep in mind this limitation when setting kernel parameters related to shared memory or creating huge pages.
You install Oracle Business Intelligence and Oracle TimesTen on one virtual machine, and Oracle Essbase (if deployed) on the second virtual machine.
This section consists of the following topics:
Section 2.3.1, "Prerequisites to Installing and Configuring Exalytics Software on Virtual Machines"
Section 2.3.2, "Installing and Configuring Exalytics Software on Virtual Machines"
The following prerequisites must be met before installing the Exalytics software on the virtual machines:
You have created a virtual machine.
You have created a virtual disk on RAID5 and associated it with the virtual machines.
This section consists of the following topics:
Section 2.3.2.2, "Modifying Oracle User and Granting Permissions"
Section 2.3.2.3, "Installing Oracle Business Intelligence and Oracle TimesTen"
Before you can install the Exalytics software, you create and mount a /u01 partition on the virtual disk.
To create and mount a /u01 partition:
After logging in as the root user, configure the /u01 directory on the virtual disk using commands such as the following ones:
To create a partition, enter the following commands:
parted /dev/xvdb
GNU Parted 1.8.1
Using /dev/xvdb
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) mklabel msdos
(parted) mkpart primary 0 1600GB
(parted) print
Model: Xen Virtual Block Device (xvd)
Disk /dev/xvdb: 1600GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Number Start End Size Type File system Flags
1 32.3kB 1600GB 1600GB primary
(parted) quit
To create logical volume, enter the following commands:
lvm pvcreate /dev/xvdb1
Physical volume "/dev/xvdb1" successfully created
lvm vgcreate VolGroup01 /dev/xvdb1
Volume group "VolGroup01" successfully created
To view free extents on VolGroup01, enter the following commands:
vgs -o +vg_free_count,vg_extent_count
VG #PV #LV #SN Attr VSize VFree Free Ext
VolGroup01 1 0 0 wz--n- 1.46T 1.46T 381469 381469
lvm lvcreate --extents 381469 --name LogVol00 VolGroup01
Logical volume "LogVol00" created
To create a file system, enter the following command:
mkfs.ext3 /dev/VolGroup01/LogVol00
Add the following line to the /etc/fstab file:
/dev/VolGroup01/LogVol00 /u01 ext3 defaults 0 0
To mount the directory, enter the following commands:
mkdir /u01
mount /u01
Verify that the partition has been created by entering the following command:
df –lh
The VM template contains "oracle" as the operating system user name. Associate the user name with the "oinstall" group and create a password for it.
To modify Oracle user and grant permissions:
Perform the following actions as root:
Enter the following commands to associate the user name "oracle" with the group "oinstall" and to create a password:
groupadd oinstall
usermod –g oinstall oracle
passwd oracle
Enter the following commands to grant permissions to the /u01 drive where the software is to be installed:
chown oracle:oinstall /u01
chmod 775 /u01
Start the VNC Server on the virtual machine.
For detailed instructions on installing Oracle Business Intelligence and Oracle TimesTen, see Chapter 3, "Installing Software on the Exalytics Machine."
If deploying Oracle Essbase, install Oracle Essbase on a separate virtual machine.
To install Oracle Essbase:
Connect to a virtual machine.
Navigate to the Oracle Software Delivery Cloud web site at the following link:
For Product Pack, select Oracle Enterprise Performance System.
For Platform, select Linux x86-64.
Click Go.
Select and download Oracle Enterprise Performance Management System Media Pack 11.1.2.2.0 for Linux x86-64
Download Oracle Essbase, which includes the following:
System Configurator
Foundation Services
Essbase and Static Content
Unzip the zip files to the MW_HOME directory.
Navigate to the folder where you unzipped the files (MW_HOME), and run the following command to install Oracle Essbase:
./installTool.sh
Navigate to MW_HOME/EPMSystem11R1/common/config/11.1.2.0.
Run the following command to create a domain:
./configtool.sh
For more information, see Oracle Enterprise Performance Management System Installation and Configuration Guide Release 11.1.2.3 at the following location:
http://docs.oracle.com/cd/E40248_01/epm.1112/epm_install.pdf