D Messages and Translated Messages

This appendix summarizes the T10000 tape drive operator-panel indicator lights and display messages. Where applicable, this appendix recommends operator actions.

Messages

Table D-1 lists operator panel display messages, meanings, and recommended actions.

Table D-1 Operator Panel Display Messages

Display Meaning Recommended Action

* (asterisk)

The tape drive is online but a cartridge tape is not loaded.

Load a cartridge tape as required.

ASIA Diags

IPL diagnostics are executing.

None

Bank n Bad

During boot, a section of memory was found bad.

Perform a drive IPL. If the problem persists, contact authorized service personnel.

Boot Fail

The IPL failed.

Perform a drive IPL again. If the problem persists, contact authorized service personnel.

BT Monitor

A sequence of switches accessed an engineering area.

Perform a drive IPL.

CC Diags

IPL diagnostics are executing.

None

Chk xxxx, xxxx is an FSC

An operational failure occurred; the tape drive automatically performs an IPL.

Wait for the IPL to complete and retry the operation (see Table D-2). If the problem persists, contact authorized service personnel.

Cleaning (*Cleaning*)

A cleaning cartridge is in the tape drive and is now cleaning.

None

cnhndnsn (Hardware revision level supported by the firmware in this drive)

The tape drive firmware level is insufficient to control the tape drive hardware.

Contact authorized service personnel.

CodCrFail1

The tape drive cannot write code onto the data cartridge tape, or the tape drive cannot position the data cartridge tape.

Ensure that the tape is write-enabled, or try another cartridge tape.

CodCrFail2

The tape drive cannot read code from the data cartridge tape.

Retry the operation, or try another cartridge tape. If the problem persists, contact authorized service personnel.

CodeUpDate

The firmware in the tape drive is being updated from the host; the operator panel switches are locked.

None

CodUpFail1

The tape drive cannot read the data cartridge tape, or the tape drive cannot position the data cartridge tape.

Try another cartridge tape.

CodUpFail2

The EEPROM failed.

Contact authorized service personnel.

CodUpFail3

The tape drive cannot read code from the data cartridge tape.

Retry the operation, or try another cartridge tape. If the problem persists, contact authorized service personnel.

CodUpFail4

The data cartridge tape is not a code update cartridge tape.

Try another code update cartridge tape.

If the problem persists, contact authorized service personnel.

DatCrFail1

The tape drive cannot create (reformat or reclaim) a cartridge tape.

Ensure that the data cartridge tape is write-enabled, or try to reformat the tape on another drive. If the problem persists, contact authorized service personnel.

DmpCrFail1

The tape drive cannot create (reformat or reclaim) a diagnostic dump tape.

Ensure that the data cartridge tape is write-enabled. If the problem persists, contact authorized service personnel.

DmpCrFail2

The tape drive cannot read the format of the data cartridge tape.

Retry the operation, or try another cartridge tape. If the problem persists, contact authorized service personnel.

DmpWrFail1

The tape drive cannot write diagnostic data onto the data cartridge tape, or the tape drive cannot position the data cartridge tape.

Contact authorized service personnel.

DmpWrFail2

There is no diagnostic dump data to process.

Contact authorized service personnel.

xxxx:Dmp y

Alternates with *(an asterisk) after completion of IPL, where xxxx = the FSC of last dump data collected and Y = number of uncollected dumps in non-volatile memory.

Contact authorized service personnel who accesses the diagnostic data and collects it to tape or to the host.

DumpAgain? alternating with Chk xxxx, xxxx is an FSC. The Service indicator is flashing.

The tape drive detected the same error within a minute.

IPL the tape drive. If the problem persists, contact authorized service personnel.

DumpToHost

The dump or event log is being transferred to the host; operator panel switches are locked.

None

Exp ClCart

The cleaning cartridge is used up.

Replace the cleaning cartridge.

Fix CfgErr

The checksum does not match after an IPL.

Contact authorized service personnel.

Init xxxx. xxxx is an FSC

An initialization error occurred.

Contact authorized service personnel.

IPL Pend

The IPL switch has been pressed.

None

Load CC

The common controller code is loading; IPL is proceeding.

None

Loading

A cartridge tape is loading.

None

Load xxxx, xxxx is an FSC

The load or unload operation failed.

If the load failed, insert another cartridge tape. If it loads successfully, suspect the original tape. If another tape fails to load, IPL the tape drive.

If the problem persists, contact authorized service personnel.

Load FIBRE

Fibre Channel firmware is loading; IPL is proceeding.

None

Locating

The tape drive is doing a high-speed seek.

None

Memory Err

The IPL failed.

Perform the tape drive IPL again. If the problem persists, contact authorized service personnel.

NTReady F

A write-protected tape is in the process of a manual unload.

None

NTReady U

A write-enabled tape is in the process of a manual unload.

None

Offline alternating with *

The tape drive is offline.

None

Online

The tape drive is online.

None

Power Fail

The power supply failed.

Contact authorized service personnel.

Reading

The tape drive is reading data.

None

Ready A

The loaded cartridge tape is a VolSafe cartridge.

None

Ready F

The loaded cartridge tape is write-protected.

None

Ready H

The loaded higher density, non-VolSafe cartridge tape is ready and not file protected in a lower density drive.

Reload with a low-density cartridge or intentionally over-write from BOT.

Note - High-density data cannot be read by a lower density drive.

Ready L

The loaded lower density, non-VolSafe cartridge tape is ready and not file protected in a higher density drive.

Use for read-only jobs or intentionally over-write from BOT.

Note - Low-density data file can be read, but not revised by a higher density drive.

Ready U

The loaded cartridge tape is write-enabled (write-unprotected).

None

Rewinding

The tape drive is rewinding.

None

Save Fails

The new configuration cannot be saved because the read-access memory (RAM) might be defective.

This message is associated with changing the tape drive configuration, a task for authorized service personnel only.

SavingDump

A dump is being saved to non-volatile memory.

None

Start Init

Initialization has started.

None

Trapped

The IPL process is trapped in a loop.

IPL the tape drive again. If the problem persists, contact authorized service personnel.

Unloading

A cartridge tape is unloading.

None

UnWr xxxx, where xxxx is an FSC

The Unload switch was pressed during a write operation. Some data remains unwritten.

To write the unwritten data, issue the command:

ESCON Swap in VM/MVS environment

Or, Press the Unload switch again; the unwritten data is lost.

Write Prot

The tape drive attempted to write to a write-protected cartridge tape.

Change the switch on the data cartridge tape to enable writing.

Writing

The tape drive is writing data.

None


Potential Operator Recovery Scenarios

The following table contains Fault Symptom Codes (FSCs) that commonly result from an operator error. The first column in the table lists an operator panel message at the time of the error event. The description column provides insight into the error condition from which you can determine a recovery action.

Table D-2 Selected Check Message Meanings

Message Description

CHK 6109

This drive does not contain the key needed to decrypt this tape. The ID of the missing key can be viewed from this drive using the VOP program.

CHK A33A

The user requested a motion operation that requires a tape to be installed, however, a tape has not been loaded.

CHK A34C

The user requested a write operation that requires a tape to be installed, however, a tape has not been loaded.

CHK A3FB

A format override tape write operation failed. The failure may not be serious. Error recovery was not invoked for the failure. Re-attempting the test may resolve this issue.

CHK A733

The operator or library inserted a write protected tape into the drive while in a menu selected create tape mode. If the write protect switch on the cartridge is moved to the unlocked position, the operation will work.


Translated Messages

Table D-3 lists operator panel display messages selected for translation. The messages appear in the language set in the drive configuration menu.

Note:

See "Language Selection Submenu" for additional information.

Table D-3 Translated Display Messages

English Espanol Francais Italiano Deutsch

*Cleaning*

*LIMPIEZA*

*NETTOYAGE

*PULIZIA*

*REINIGEN*

*Erasing*

*BORRANDO*

EFFACEMENT

*CANCELLA*

*LOESCHEN*

Locating

Localizar

Recherche

Ricerca

Suchen

Loading

Cargando

Chargement

Carico

Laden

NT Ready F

No Listo A

NPret F

No Prnt F

N Bereit F

NT Ready U

No Listo U

NPret U

No Prnt U

N Bereit U

Ready A

Listo A

Pret A

Pronto A

Bereit A

Ready F

Listo F

Pret F

Pronto F

Bereit F

Ready H

Listo H

Pret H

Pronto H

Bereit H

Ready L

Listo L

Pret L

Pronto L

Bereit L

Ready U

Listo U

Pret U

Pronto U

Bereit U

Rewinding

Rebobinar

Rebobinage

Riavvolgi

Spulen

Unloading

Descarga

Dechargemt

Scarico

Entladen