システム・メッセージ: Qカタログ1300-1399
|
1350 |
ERROR: operation - failed to open table qspace.extent on config config | |
|
Description |
The specified operation could not open the queue space extent, qspace.extent, on the specified configuration, config. The operation is one of the following: |
Action |
Normally this error results from specifying an invalid queue space name or configuration device. When using | |
See Also |
| |
1351 |
ERROR: operation - failed to read block block of table qspace..extent on config config | |
|
Description |
The specified operation could not read a block from the queue space extent, qspace.extent, on the specified configuration, config. The operation values are listed in message 1350. |
Action |
This probably indicates a disk error or problem and normally means that a message will be lost. Contact your Oracle TUXEDO system Technical Support. | |
1352 |
ERROR: operation - failed to write block block of table qspace..extent on config config | |
|
Description |
The specified operation could not write a block to the queue space extent, qspace.extent, on the specified configuration, config. The operation values are listed in message 1350. |
Action |
This probably indicates a disk error or problem and may mean that a message will be lost. Contact your Oracle TUXEDO system Technical Support. | |
1353 |
ERROR: operation - checksum failed on block block of table qspace..extent on config config | |
|
Description |
The specified operation could read a block from the queue space extent qspace.extent on the specified configuration, config, and found that its checksum was not valid. The operation values are listed in message 1350. |
Action |
This probably indicates a disk error or problem and normally means that a message will be lost. Contact your Oracle TUXEDO system Technical Support. | |
1354 |
ERROR: operation - queue space for rmid rmid not defined or not open | |
|
Description |
The specified operation was executed but the queue space (the resource manager identified by rmid) either didn't exist or was not open. The operation values are listed in message 1350. This probably indicates that a System/T client or server did not call tpopen() before starting a transaction. |
Action |
Call tpopen() to open the queue space before doing any transaction operations. | |
See Also |
| |
1355 |
ERROR: [operation - invalid flags 0xflags] | |
|
Description |
An invalid flags value, flags, was passed from the transaction manager to the specified operation(xa_start, xa_end, xa_prepare, xa_commit, xa_rollback, xa_recover, or xa_forget). |
Action |
Contact your Oracle TUXEDO system Technical Support. | |
1356 |
ERROR: operation - queue space qspace needs to be restarted | |
|
Description |
An error was detected in the queue space that requires the resource manager to be restarted. Normally, this is caused by the abnormal termination of a process attached to the queue space while it was in a critical section of code. |
Action |
Stop all processes attached to the queue space, remove the IPC resources using the qmadmin ipcrm command, and restart the processes. | |
See Also |
| |
1357 |
ERROR: operation - invalid queue name name | |
|
Description |
An invalid queue name, name, was specified for the specified operation. The operation can be one of the following: "Queue information", "Queue list", "Change priority", "Change exec time", "Change expiration time", "Change queue", "Delete messages", or "Destroy queue". |
Action |
Use the qinfo command to list the available queues in the queue space and re-enter the command with a valid queue name. | |
See Also |
| |
1358 |
ERROR: Device offset + size exceed limitG OS limitation | |
|
Description |
While executing the crdl command, the offset + size exceed limit OS limit. |
Action |
Ensure that devices created with crdl are under the limit OS limit. Use qspacecreate and qaddext to support qspace larger than limit OS limit. Note: Each device must be under the limit OS limit. | |
See Also |
| |
1360 |
WARN: Print transaction - unable to save transaction information; committrans and aborttrans not available | |
|
Description |
While executing the qprinttrans command, the transaction information that can be subsequently used for qcommittrans or qaborttrans could not be saved because malloc() failed. |
Action |
It will not be possible to execute qcommittrans or qaborttrans successfully. No action required. | |
See Also |
| |
1377 |
ERROR: operation - must execute printtrans to get transaction information | |
|
Description |
The qcommittrans or qaborttrans command was executed without previously executing printtrans successfully (that is, without getting message 1377) to get a list of transactions. |
Action |
Execute the qprinttrans command to get a list of transactions. An index for one of the listed transactions must be specified for the qcommittrans or qaborttrans command. | |
See Also |
| |
1378 |
ERROR: operation - invalid transaction index specified | |
|
Description |
While executing the qcommittrans or qaborttrans command, a transaction index was specified that did not match an index printed by the qprinttrans command. |
Action |
Specify a valid transaction index from the output of the qprinttrans command. | |
See Also |
| |
1379 |
ERROR: operation - transaction for the index specified has changed | |
|
Description |
While executing the qcommittrans or qaborttrans command, a transaction index was specified for a transaction that no longer exists (that is, has already been completed). |
Action |
Re-execute the qprinttrans command to get a list of transactions that are currently outstanding and re-enter the qcommittrans or qaborttrans command with a valid transaction index. | |
See Also |
| |
1381 |
ERROR: operation - cannot heuristically complete, status status | |
|
Description |
While executing the qcommittrans or qaborttrans command, a transaction index was specified for a transaction that is not in the READY state. The current status of the transaction, status, is printed in the system message. |
Action |
Execute the qprinttrans command to get a list of currently outstanding transactions. Only transactions in the READY state may be specified for the qcommittrans or qaborttrans command. | |
See Also |
| |
1398 |
INFO: Queue information - no queues defined. | |
|
Description |
The qinfo command was executed but no queues are currently defined in the open queue space. |
Action |
No action required. | |
See Also |
| |
1399 |
エラー: キューのスキャン - メモリーの割当てに失敗しました | |
|
説明 |
malloc()を使用してオペレーティング・システムから動的にメモリーを割り当てようとしましたが、キューのスキャン中に失敗しました。関連付けられている操作(qlist、qchangetime、qchangeprio、qchangequeueまたはqdeletemsg)は失敗します。 |
アクション |
マシンのメモリー量およびプロセスによって使用されるメモリー量に対して、オペレーティング・システム・パラメータが正しく設定されていることを確認してください。マシンのメモリー使用量を減らすか、マシンの物理メモリー量を増やしてください。 | |
関連項目 |
|