ibm3584 - Describes using the IBM 3584 UltraScalable Tape Library with StorageTek QFS or Oracle HSM software. The procedures outlined here do not apply to the IBM TS3500 or TS4500 tape libraries.
SUNWsamfs
The IBM 3584 UltraScalable tape library can be used by StorageTek QFS and Oracle HSM software with few modifications to its typical operations. This man page describes the steps you need to take to use this library effectively. The following topics are described:
Cleaning
Using the IBM 3584 tape library's partitioning feature
The IBM 3584 UltraScalable Tape Library can be used in a StorageTek QFS or Oracle HSM environment, but you need to disable automatic cleaning and enable hosted cleaning. No other modifications need to be made to this library's default configuration.
Host cleaning enables the host to detect the need to clean an Ultrium Tape Drive and to control the cleaning process. Host cleaning with a cleaning cartridge is only supported when you disable automatic cleaning and only for the logical library in which each cleaning cartridge is stored. When you enable automatic cleaning, or when the cleaning cartridge is stored in a different logical library, the host application does not have access to the cleaning cartridge.
When automatic cleaning is disabled, the library continues to detect the need to clean a tape drive. When the need is detected, the library displays the physical location of the drive in the following message:
CLEAN [Fx,Rzz]
The preceding message is interpreted as follows:
F
represents the frame, and x
represents its number
R
represents the row, and xx
represents its number
The message clears after you clean the drive by using the supported cleaning method. The cleaning cycle takes less than 2 minutes.
When you enable or disable automatic cleaning, the selected setting is stored in nonvolatile memory and becomes the default during later power-on cycles.
To disable automatic cleaning, perform the following steps:
Ensure that a cleaning cartridge is loaded in the library.
From the library's activity screen, press MENU
. The main menu displays, as
follows:
-------------------------------------------------------------------------- Main Menu Panel 0002 Library Status Manual Operations Settings Usage Statistics Vital Product Data Service [BACK] [UP] [DOWN] [ENTER] --------------------------------------------------------------------------
Press UP
and DOWN
to highlight Settings.
Press ENTER
.
The Settings
menu displays, as follows:
-------------------------------------------------------------------------- Settings Panel 0100 Configuration Cleaning Mode Display∕Change SCSI IDs Add∕Remove Control Paths Date∕Time Sounds [BACK] [UP] [DOWN] [ENTER] --------------------------------------------------------------------------
Press UP
or DOWN
to highlight Cleaning Mode
.
Press ENTER
. The Cleaning Mode
screen displays and indicates whether automatic cleaning is currently enabled
or disabled.
-------------------------------------------------------------------------- Cleaning Mode Panel 0110 Automatic Cleaning is ENABLED Disable Automatic Cleaning [BACK] [ENTER] --------------------------------------------------------------------------
The ENTER
key acts as a toggle switch for the two choices.
Press ENTER
until Disable Automatic Cleaning
is highlighted.
You should receive the following message:
If you continue you will set the Automatic Cleaning Mode to DISABLED.
If you disable automatic cleaning you should ensure that each
logical library has at least one cleaning cartridge since host-initiated
cleaning can not use a cleaning cartridge located in a different logical
library. Do you want to continue?
Press YES
to disable automatic cleaning.
The Cleaning Mode
screen redisplays with the new setting.
Press BACK
until you return to the Activity
screen from step 1.
If your IBM 3584 tape library contains 2 or more drives, it can be partitioned into 2 or more logical libraries. If you have partitioned this library, make sure that it is operating as you configured it prior to installing any StorageTek QFS or Oracle HSM software. For more information on partitioning this library, see your IBM documentation. This subsection describes aspects of using the partitioning feature with the StorageTek QFS and Oracle HSM software.
When a cartridge is exported (as opposed to being placed in the drawer by a human), only the partition from which it was exported can access that drawer slot. If the cartridge is removed and re-inserted by a human, it is accessable to any∕all partitions. The act of removal referred to in this subsection consists of the following steps:
Open door.
Remove cartridge(s).
Close door.
Wait for door to lock and then unlock.
Open door.
Replace cartridge(s).
Close door.
Much of the text on this man page was derived from the IBM 3584 UltraScalable Tape Library Planning and Operator Guide, IBM publication GA32-0408-01, copyright IBM Corporation 2000.
IBM 3584 UltraScalable Tape Library Planning and Operator Guide, IBM publication GA32-0408-01.
http:∕∕www.ibm.com∕storage∕hardsoft∕tape∕lto∕3584