Go to primary content
Oracle® Communications Measurements Reference
Release 46.6
E93320 Revision 1
Go To Table Of Contents
Contents

Previous
Previous
Next
Next

STPLAN MTCD Report

Example Commands:

UI: rept-meas:type=mtcd:enttype=stplan

FTP: rept-ftp-meas:type=mtcd:enttype=stplan

Table 3-77 Daily Maintenance (MTCD) and Day-to-Hour Maintenance (MTCDTH) STPLAN Measurements

Event Name Description Unit

ENETALNERR

Ethernet Alignment Error - Number of packets not received over the STPLAN interface because of ethernet alignment errors.

peg count

ENETBUSBSY

Ethernet Bus Busy - Number of transmissions attempted when the STPLAN ethernet bus was busy.

peg count

ENETCRCERR

EthernetCRC Error - Number of packets not received on the STPLAN ethernet due to CRC errors.

peg count

ENETCOLERR

Ethernet Collision Error - Number of packets not transmitted by STPLAN because of excessive collisions on the STPLAN ethernet bus.

peg count

ENETOCTRCV

Ethernet Octets Received - The total number of octets received on the STPLAN ethernet interface.

peg count

ENETOCTXMT

Ethernet Octets Transmitted - The total number of octets transmitted on the STPLAN ethernet interface.

peg count

ENETOVRERR

Ethernet Receive Buffer Overflow Errors -

Number of packets not received by STPLAN because of a receive buffer overflow.

peg count

IPADDRERR

IP Address Error- The total number of inbound IP datagrams discarded on the STPLAN interface due to a bad destination address.

peg count

IPHDRERR

IP Header Errors - The total number of inbound IP datagrams discarded on the STPLAN interface due to header errors.

peg count

IPPROTERR

IP Protocol Error - Number of inbound IP datagrams discarded by STPLAN due to an error in the packet (invalid protocol).

peg count

SLANDISC1

STPLAN Discarded 1 - Number of SLAN MSUs discarded by the LIM cards for STPLAN feature disabled and records aging off of the local queue.

peg count

SLANDISC2

STPLAN Discarded 2 - Number of SLAN MSUs discarded by the SLAN cards for network problems and unreachable far end servers. During network outages, the SLAN cards will stop TVG/MFC grants or go into flow control. This causes the PDUs to be queued on the LIM cards, so the majority of discards will be pegged on SLANDISC1 under these circumstances.

peg count

SLANDSBLD

STPLAN Disabled - The duration that the STPLAN screening/copy feature was disabled.

msecs

SLANSCRND

STPLAN Screened - Number of MSUs that were copied to the STPLAN interface after passing gateway screening.

peg count

SLANXMIT

STPLAN Transmit - Number of MSUs sent to the host destination.

peg count

STATUS

Indication of Data Validity:
  • K indicates good data
  • I indicates incomplete interval
  • N indicates data not current

status

TCPCONNFLD

TCP Connections Failed - The total number of TCP connections that have failed on the STPLAN interface.

peg count

TCPRCVERR

TCP Receive Error - The total number of TCP segments received on the STPLAN interface in error.

peg count

TCPRSTSENT

TCP Reset Sent - The total number of TCP segments sent containing the reset (RST) flag on the STPLAN interface.

peg count

TCPSEGRCVD

TCP Segment Received - The total number of TCP segments received on the STPLAN interface.

peg count

TCPSEGSENT

TCP Segment Sent - The total number of TCP segments sent on the STPLAN interface.

peg count

TCPSEGXMT2

TCP Segment Retransmitted - The total number of TCP segments retransmitted on the STPLAN interface.

peg count

UI Example Output:

    tekelecstp 01-08-18 00:00:21 EST EAGLE 34.0.0
    TYPE OF REPORT: DAILY MAINTENANCE MEASUREMENTS ON STPLAN
    REPORT PERIOD: LAST
    REPORT INTERVAL:  01-08-17  00:00:00 THRU 23:59:59
    STPLAN-MTCD MEASUREMENTS
    SLANDSBLD  =         0, SLANDISC1  =         0, SLANDISC2  =         0,
    SLANSCRND  =         0, SLANXMIT   =         0, ENETALNERR =         0,
    ENETCRCERR =         0, ENETCOLERR =         0, ENETBUSBSY =         0,
    ENETOVRERR =         0, ENETOCTXMT =         0, ENETOCTRCV =         0,
    TCPCONNFLD =         0, TCPSEGRCVD =         0, TCPSEGSENT =         0,
    TCPSEGXMT2 =         0, TCPRCVERR  =         0, TCPRSTSENT =         0,
    IPHDRERR   =         0, IPADDRERR  =         0, IPPROTERR  =         0
;
    tekelecstp 01-08-18 00:00:22 EST EAGLE 34.0.0
    END OF DAILY STPLAN-MTCD MEASUREMENT REPORT
;

FTP Example Output File Name: mtcd-stplan_19990116_2400.csv

FTP Example Output File Format:

"CLLI","SWREL","RPTDATE","RPTIME","TZ","RPTTYPE","RPTPD","IVALDATE",
"IVALSTART","IVALEND","NUMENTIDS"<cr><lf>
"tekelecstp","34.0.0-39.1.0","1999-01-17","15:51:37","EST",
"DAILY MAINTENANCE MEASUREMENTS ON STPLAN","LAST","1999-01-16","00:00:00","24:00:00",1<cr><lf>
<cr><lf>
"STATUS","SLANDSBLD","SLANDISC1","SLANDISC2","SLANSCRND","SLANXMIT","ENETALNERR",
"ENETCRCERR","ENETCOLERR","ENETBUSBSY","ENETOVRERR","ENETOCTXMT","ENETOCTRCV",
"TCPCONNFLD","TCPSEGRCVD","TCPSEGSENT","TCPSEGXMT2","TCPRCVERR","TCPRSTSENT",
"IPHDRERR","IPADDRERR","IPPROTERR"<cr><lf>
"K",0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0<cr><lf>

Typical file size is:

Table 3-78 Typical File Size: mtcd-stplan.csv

System header + Report header + Report data = File Size

250

+

271

+

130

=

651 bytes