List of Tables

• 1-1        Admonishments
• 2-1        Action Commands and Associated System Entity
• 2-2         Keyboard Functions
• 2-3        Unsolicited Output Message Groups
• 4-1         TRIGTYPE Parameter Values
• 4-2         Valid Parameter Combinations for chg-appl-rtkey Routing Key Types
• 4-3        Maximum IP Associations and Links
• 4-4         Validation Rules for Association Establishment
• 4-5        Alias Combination Matrix
• 4-6        EIR Response Type Values
• 4-7         Valid Parameter Combinations for chg-gtt Routing Parameters
• 4-8         Gateway Screening Stop Action Definitions
• 4-9        Standard DSCP Values
• 4-10       Default Subnet Mask Values
• 4-11      slsocbit example (chg-ls)
• 4-12      NI Mapping Rules
• 4-13       Incoming SLS Bit Rotation for ANSI Linksets
• 4-14       Supported chg-scr-sio Parameter Combinations
• 4-15      Standard DSCP Values
• 4-16      NPCFMTI Parameter - ITU National Point Code Values
• 4-17      Point Code Format Examples
• 4-18       TON2NAI Mapping Default Values
• 4-19       NAI2TON Mapping Default Values
• 4-20       Valid and Default UAPS Parameter Values
• 4-21       Minimum Hardware Required for LNP Quantity Features
• 4-22      TPS Capacities
• 4-23       TRIGTYPE Hexadecimal Codes
• 4-24       Valid ent-gtt Routing Parameter Combinations
• 4-25       ENT-LG-EVENT Generic Parameters
• 4-26       ENT-LG-EVENT Rx MSU Event Type common Parameters
• 4-27       ENT-LG-EVENT Tx MSU Event Type common Parameters
• 4-28       ENT-LG-EVENT Tx MSU Event Type Specific Parameters (SI = 0)
• 4-29       ENT-LG-EVENT Tx MSU Event Type Specific Parameters (SI = 1, 2, 6-12, 14, 15)
• 4-30       ENT-LG-EVENT Tx MSU Event Type Specific Parameters (SI = 3)
• 4-31       ENT-LG-EVENT Tx MSU Event Type Specific Parameters (SI = 4, 5, 13)
• 4-32       Incoming SLS Bit Rotation for ITU
• 4-33       Incoming SLS Bit Rotation for ANSI
• 4-34      SLSOCBIT example (ent-ls)
• 4-35       SLS Bit Rotation
• 4-36       Additional Valid ent-scr-sio Parameter Combinations
• 4-37       DMS.CFG File Location for format-disk Command
• 4-38      Disk Format Capacity
• 4-39       Route Set Test When LNP is Offline
• 4-40       Receiving Messages when LNP is Offline 
• 4-41      Using init-card Parameters
• 4-42      rept-ftp-meas Valid Parameter Combinations
• 4-43       rept-imt-info Statistics, Low Speed Summary (rept-imt-info:report=(hmuxerr, hiprerr, or hipr2err))
• 4-44       rept-imt-info Statistics, High Speed Summary
• 4-45       rept-imt-info Statistics, Miscellaneous Summary
• 4-46      Hexadecimal/Decimal Values for s and e Parameters
• 4-47       Level 1 IMT Statistics
• 4-48       Level 1 IMT Statistics, High Speed Error Summary
• 4-49      Valid Parameter Combinations for the type Parameter
• 4-50      Maximum Supported Links based on Card Type and GPL
• 4-51       Auto-Inhibit Hardware Verification Codes
• 4-52       IMT Bus States
• 4-53      Baseline Configuration Changes for the E5-ENET-B Card
• 4-54      MaxTPS Per Card
• 4-55       Retrieve Commands for Additional Table Information
• 4-56       Time Zones Set by the set-time Command
• 4-57       Test Disk Execution Times
• A-1        Summary of Ranges for link Parameter
• A-2        Valid CIC Ranges for SI and MSU Types
• A-3        DRANAIV/DRANAI Mapping
• A-4        DRANPV/DRANP Mapping
• A-5        NAIV/NAI Mapping
• A-6        NPV/NP Mapping
• A-7        Valid Card Applications and Types
• A-8        Loopback Testing Commands and Functions
• A-9        Commands that support the Spare Point Code Prefix
• A-10      Commands that support the Private Point Code Prefix