0116 - Link Expected IP TPS Threshold Exceeded

This message indicates that the actual link transaction rate is approaching the link's fair share of provisioned linkset capacity.

This message indicates that the actual link transaction rate exceeds the link capacity alarm threshold defined by slkusealm, tpsalmtype and slktps (rsvdslktps or maxslktps based on tpsalmtype) parameters.

Example

RLGHNCXA21W 00-12-07 12:01:43 EST  EAGLE 35.0.0
* 0014.0116  * SLK 1104,A LSA01   Link expected IP TPS threshold exceeded
               SLC=01   FECLLI=A1234567890

Alarm Level: Minor

Recovery

1. Enter the following command to display the current and peak IPSG TPS utilization of the linkset specified in the output:
   rept-stat-iptps:lsn=xxxxxx

   where xxxxxx is the linkset name as defined in the output.

   Example of the output:

   eagle10115 03-05-06 09:49:20 EST EAGLE 31.6.0
       IP TPS USAGE REPORT
                  THRESH  CONFIG         TPS     PEAK       PEAKTIMESTAMP
       ------------------------------------------------------------------
       LSN
       LSGW1101     100%  188000  TX:    800      800  03-05-05 09:49:19 
                                 RCV:    800      800  03-05-05 09:49:19
       ------------------------------------------------------------------
       LOC  PORT
       1101    A     80%    ----  TX:    800      800  03-05-05 09:49:19 
                                 RCV:    800      800  03-05-05 09:49:19
       1103    A     80%    ----  TX:    800      800  03-05-05 09:49:19 
                                 RCV:    800      800  03-05-05 09:49:19
       ------------------------------------------------------------------
       Command Completed.

2. Enter the rtrv-ls:lsn=xxxxxx command, where xxxxxx is the linkset name, to review current slkusealm, tpsalmtype (TPSALM), rsvdslktps and maxslktps parameter values:

   Searching link set table on disk - please wait...
   
   Command Accepted - Processing
   
       eagle11 16-10-13 12:11:41 EST  EAGLE 46.3.0.0.1-68.27.0
       rtrv-ls:lsn=lab2m2pa
       Command entered at terminal #1.
   ;
   
       eagle11 16-10-13 12:11:42 EST  EAGLE 46.3.0.0.1-68.27.0
   
                                        L3T SLT              GWS GWS GWS
       LSN           APCN   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
       lab2m2pa      02000         none 1   2   no  B   1    off off off no    off
   
                     SPCN          CLLI         TFATCABMLQ MTPRSE ASL8
                  ---------------- -----------  1          ---    ---
   
                  SLSRSB RANDSLS ITUTFR
                  1      off     off
   
                  IPSG  IPGWAPC  GTTMODE           CGGTMOD   PCT  CHGMTP3OPC
                  yes   no       SysDflt             no      off  on
   
                  ADAPTER    RSVDSLKTPS  MAXSLKTPS
                  m2pa       500         500
   
                  TPSALM     LSUSEALM    SLKUSEALM
                  rsvdslktps 100%        80%
   
                  LOC  LINK SLC TYPE     ANAME
                  1216 A2   0   IPSG     lab2m2pa
   
   
       Link set table is (16 of 1024) 2% full.

3. Refer to the Commands User's Guide to interpret the output.
   If the linkset has adequate bandwidth, then the IP TPS for the linkset can be increased (using the chg-ls command), provided the current IPGWx IPSG system IP TPS setting allows for this. The IP TPS SLK alarm threshold percent (slkusealm) can also be adjusted if allowed by the current setting. If the linkset does not have adequate bandwidth, then more links are required to correct the problem.