5.1.39 MTP3 Config

A Mtp3 Config is an entity to configure all the m3rl timers.

Select the VSTP, and then Configuration, and then MTP3 Configs page. The page displays the elements on the MTP3 Configs View, Insert, and Edit pages.

Note:

Data Input Notes apply to the Insert and Edit pages only; the View page is read-only.

Table 5-39 MTP3 Configs Elements

Element	Description	Data Input Notes
Name *	Name for this M3rl Config, which must be unique within the VSTP site.	Valid names are strings between one and 32 characters, inclusive. Valid characters are alphanumeric and underscore. The name must contain at least one alpha and must not start with a digit. [A value is required.]
Linkset On Hold timer	Link addition/deletion changeover timer duration. This timer introduces a delay to help prevent message mis-sequencing on link add/deletion.	Typical value is 60. [MIN,MAX] = [10,2000]
Signaling Link Test T1 Timer	Supervision timer for signaling link test acknowledgement message.	Typical value is 12000.[MIN,MAX] = [4000,12000]
Signaling Link Test T2 Timer	Interval timer for sending signaling link test messages.	Typical value is 30000.[MIN,MAX] = [30000,90000]
Signaling Link Test T17 Timer	SLT T17 timer set.	Typical value is 2000. [MIN,MAX] = [500,2000]
Timer 10	Timer 10 - Wait to repeat signaling route set test (SRST) message.	Typical value is 30000.[MIN,MAX] = [20000,90000]
Timer 11	Timer 11 - Transfer restricted; in milliseconds.	Typical value is 30000.[MIN,MAX] = [1000,90000]
Timer 12	Timer 12 - Linkset inhibited; in milliseconds.	Typical value is 800.[MIN,MAX] = [800,1500]
Timer 13	Timer 13 - Linkset inhibited; in milliseconds.	Typical value is 800.[MIN,MAX] = [800,1500]
Timer 15	Timer 15 - Wait for repeat route set congestion test (RSCT).	Typical value is 3000.[MIN,MAX] = [200,4000]
Timer 16	Timer 16 - Wait for route set congestion test (RSCT) updates.	Typical value is 1400.[MIN,MAX] = [200,3000]
Timer 17	Timer 17 - Delay to avoid oscillation of initial alignment failure.	Typical value is 2000.[MIN,MAX] = [500,2000]
Timer 18	Timer 18 - Repeat transfer restricted (TFR) once by response method.	Typical value is 10000.[MIN,MAX] = [2000,20000]
Timer 1	Timer 1 - Changeover delay. Also used as isolation timer for ITU MTP Restart.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 2	Timer 2 - Wait for changeover acknowledgement (COA).	Typical value is 1400.[MIN,MAX] = [100,3000]
Timer 23	Timer 23 - Linkset inhibited; in milliseconds.	Typical value is 180000.[MIN,MAX] = [180000,360000]
Timer 3	Timer 3 - Time controlled diversion on changeback.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 4	Timer 4 - Wait for changeback acknowledgement (CBA) #1.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 5	Timer 5 - Wait for changeback acknowledgement (CBA) #2.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 6	Timer 6 - Controlled reroute.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 8	Timer 8 - Transfer prohibited (TFP) inhibit.	Typical value is 800.[MIN,MAX] = [500,2000]

You can perform add, edit, or delete tasks on VSTPConfigurationMTP3 Configs page.

Adding a MTP3 Config

Perform the following steps to configure a new MTP3 Config:

1. Click Insert.

   Note:

   The new MTP3 Config must have a name that is unique across all MTP3 Configs at the SOAM. In addition, the MTP3 Config's IP Port combination must also be unique across all MTP3 Configs configured at the SOAM.
2. Enter the applicable values.
3. Click OK, Apply, or Cancel

Editing a MTP3 Config

Use this procedure to change the field values for a selected MTP3 Config. (The MTP3 Config Name field cannot be changed.):

1. Select the MTP3 Config row to be edited.
2. Click Edit
3. Enter the updated values.
4. Click OK, Apply, or Cancel

Deleting a MTP3 Config

Use the following procedure to delete a MTP3 Config.

Note:

You cannot delete a MTP3 Config if it is part of the configuration of one or more Linksets.

1. Select the MTP3 Config to be deleted.
2. Click Delete.
3. Click OK or Cancel.