M3rl Options
The Message Transfer Part level 3 (MTP3) Options are configuration values that govern the overall MTP3 functionality.
The M3rl Options resources can only be updated and cannot be created or deleted.
Select the
page. The page displays the elements on the
M3rl
Options View, Insert, and Edit pages.
Note:
Data Input Notes apply to the Insert and Edit pages only; the View page is read-only.Table 5-38 M3rl Options Elements
| Element | Description | Data Input Notes |
|---|---|---|
| CnvAInat | This parameter sets the value of the called party/calling party address Reserved for National Use bit when the message is routed to the ITU national network. | Default - 1 , Minimum,Maximum - 0,1 |
| CnvCgda | This parameter enables discarding of the CGPA point code in SCCP messages if the destination network type is Ansi, and the point code or alias point code of the destination network type is not defined. | |
| CnvCgdi | This parameter enables discarding of the CGPA point code in SCCP messages if the destination network type is Itui, and the point code or alias point code of the destination network type is not defined. | |
| CnvCgdn | This parameter enables discarding of the CGPA point code in SCCP messages if the destination network type is Itun, and the point code or alias point code of the destination network type is not defined. | |
| CnvCgdn24 | This parameter enables discarding of the CGPA point code in SCCP messages if the destination network type is Itun24, and the point code or alias point code of the destination network type is not defined. | |
| CnvClgItu | This parameter enables or disables the CGPA conversion for Itui/Itui_s/Itun/Itun_s domain crossing during SCCP conversion. | |
| GtCnvDflt | This parameter enables routing of SCCP messages using system defaults when an appropriate entry is not found in the Default GT Conversion Table. | |
| Incoming SLS Bit Rotation | This parameter indicates whether an Incomig SLS Bit Rotation is enabled or not.If it is turned on and Incoming SLS Bit Rotation is applied to an MSU then the outgoing SLS bit rotation is not applied for that MSU. | |
| Linkset On Hold timer | Link addition/deletion changeover timer duration. This timer introduces a delay to help prevent message mis-sequencing on link add/deletion. | Typical value is 60. Range = 10,2000 |
| Randsls | Random SLS (signaling link selection).This parameter is used to apply random SLS generation on a per linkset basis. | |
| Signaling Link Supervision Timer | Supervision timer for signaling link test acknowledgement message. | Typical value is 12000.Range = 4000,12000 |
| Signaling Link Interval Timer | Interval timer for sending signaling link test messages. Typical value is 30000.Range = 30000,90000 | |
| SlsRotation | This parameter specifies whether the signaling link selector (SLS) of the incoming ANSI linkset is rotated before routing the messages to network. When set to true, 8 bit SLS of the incoming linkset is considered for bit rotation. | |
| Slscnv | This parameter is used as Per node SLS conversion indicator. | |
| SlsReplace | This parameter allows to replace the SLS for an ANSI message with a random generated SLS value by Random SLS feature | |
| SlsocbEnabled | This parameter turns on the Other CIC (Circuit Identification Code) Bit Used feature | |
| Timer 10 | Timer 10 - Wait to repeat signaling route set test (SRST) message. | Typical value is 30000
Range = 20000,90000 |
| Timer 11 | Timer 11 - Transfer restricted; in milliseconds. | Typical value is 30000
Range = 1000,90000 |
| Timer 15 | Timer 15 - Wait for repeat route set congestion test (RSCT). | Typical value is 3000
Range = 200,4000 |
| Timer 16 | Timer 16 - Wait for route set congestion test (RSCT) updates. | Typical value is 1400
Range = 200,3000 |
| Timer 18 | Timer 18 - Repeat transfer restricted (TFR) once by response method. | Typical value is 10000
Range = 2000,20000 |
| Timer 1 | Timer 1 - Changeover delay. Also used as isolation timer for ITU MTP Restart. | Typical value is 800
Range = 100,2000 |
| Timer 2 | Timer 2 - Wait for changeover acknowledgement (COA). | Typical value is 1400
Range = 100,3000 |
| Timer 3 | Timer 3 - Time controlled diversion on changeback. | Typical value is 800
Range = 100,2000 |
| Timer 4 | Timer 4 - Wait for changeback acknowledgement (CBA) #1. | Typical value is 800
Range = 100,2000 |
| Timer 5 | Timer 5 - Wait for changeback acknowledgement (CBA) #2. | Typical value is 800
Range = 100,2000 |
| Timer 6 | Timer 6 - Controlled reroute. | Typical value is 800
Range = 100,2000 |
| Timer 8 | Timer 8 - Transfer prohibited (TFP) inhibit. | Typical value is 800
Range = 500,2000 |
| SparePCSupportEnabled | Checks whether the support for ITUN-Spare and ITUI-Spare is enabled or disabled |
You can perform edit task on VSTP>Configuration>M3rl Options page.
Editing a M3rl Option
Use this procedure to change the field values for a selected M3rl
Option. :
- On the VSTP>Configuration>M3rl Options page, enter the updated values in the input fields.
- Click OK, Apply, or Cancel