5.1.39 MTP3 Config

A Mtp3 Config is an entity to configure all the m3rl timers.

Select the VSTP, and then Configuration, and then MTP3 Configs page. The page displays the elements on the MTP3 Configs View, Insert, and Edit pages.

Note:

Data Input Notes apply to the Insert and Edit pages only; the View page is read-only.

Table 5-39 MTP3 Configs Elements

Element	Description	Data Input Notes
Name	Name for this M3rl Config, which must be unique within the VSTP site.	Valid names are strings between one and 32 characters, inclusive. Valid characters are alphanumeric and underscore. The name must contain at least one alpha and must not start with a digit. [A value is required.]
Linkset On Hold timer	Link addition/deletion changeover timer duration. This timer introduces a delay to help prevent message mis-sequencing on link add/deletion.	Typical value is 60. [MIN,MAX] = [10,2000]
Signaling Link Test T1 Timer	Supervision timer for signaling link test acknowledgement message.	Typical value is 12000.[MIN,MAX] = [4000,12000]
Signaling Link Test T2 Timer	Interval timer for sending signaling link test messages.	Typical value is 30000.[MIN,MAX] = [30000,90000]
Signaling Link Test T17 Timer	SLT T17 timer set.	Typical value is 2000. [MIN,MAX] = [500,2000]
Timer 10	Waiting to repeat signalling route set test message.	Typical value is 30000.[MIN,MAX] = [20000,90000]
Timer 11	Transfer restricted timer.	Typical value is 30000. [MIN,MAX] = [1000,90000]
Timer 12	Waiting for uninhibit acknowledgement.	Typical value is 800. [MIN,MAX] = [100, 2000]
Timer 13	Waiting for force uninhibit.	Typical value is 800.[MIN,MAX] = [100, 2000]
Timer 15	Waiting to start signalling route set congestion test.	Typical value is 3000.[MIN,MAX] = [200,4000]
Timer 16	Waiting for route set congestion status update.	Typical value is 1400.[MIN,MAX] = [200,3000]
Timer 17	Delay to avoid oscillation of initial alignment failure and link restart.	Typical value is 800.[MIN,MAX] = [500, 2000]
Timer 18	Repeat transfer restricted (TFR) once by response method.	Typical value is 10000.[MIN,MAX] = [2000,20000]
Timer 1	Delay to avoid message mis-sequencing on changeover.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 2	Waiting for changeover acknowledgement.	Typical value is 1400.[MIN,MAX] = [100,3000]
Timer 23	Remote inhibit test timer.	Typical value is 180000.[MIN,MAX] = [180000,360000]
Timer 3	Time controlled diversion-delay to avoid mis-sequencing on changeback.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 4	Waiting for changeback acknowledgement (first attempt).	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 5	Waiting for changeback acknowledgement (second attempt).	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 6	Delay to avoid message mis-sequencing on controlled rerouting.	Typical value is 800.[MIN,MAX] = [100,2000]
Timer 8	Transfer prohibited inhibition timer (transient solution).	Typical value is 800.[MIN,MAX] = [500,2000]

You can perform add, edit, or delete tasks on VSTPConfigurationMTP3 Configs page.

Adding a MTP3 Config

Perform the following steps to configure a new MTP3 Config:

1. Click Insert.

   Note:

   The new MTP3 Config must have a name that is unique across all MTP3 Configs at the SOAM. In addition, the MTP3 Config's IP Port combination must also be unique across all MTP3 Configs configured at the SOAM.
2. Enter the applicable values.
3. Click OK, Apply, or Cancel

Editing a MTP3 Config

Use this procedure to change the field values for a selected MTP3 Config. (The MTP3 Config Name field cannot be changed.):

1. Select the MTP3 Config row to be edited.
2. Click Edit
3. Enter the updated values.
4. Click OK, Apply, or Cancel

Deleting a MTP3 Config

Use the following procedure to delete a MTP3 Config.

Note:

You cannot delete a MTP3 Config if it is part of the configuration of one or more Linksets.

1. Select the MTP3 Config to be deleted.
2. Click Delete.
3. Click OK or Cancel.