1. Virtual Signaling Transfer Point User Guide
  2. GUI Configurations
  3. Configuration
  4. TIF Options

5.1.33 TIF Options

Select the VSTP, and then Configuration, and then TIF Options page. The page displays the fields on the TIF Options View, Insert, and Edit pages.

Note:

Data Input Notes apply to the Insert and Edit pages only; the View page is read-only.

Table 5-33 TIF Options Fields

Field Description Data Input Notes
CondCGPN The preconditioning required when a CgPN lookup is needed. Default='None'

Range = 'Addcc', 'None'
CondRDN The preconditioning required when redirecting number. Default='None'

Range = 'Addcc', 'None'
CRPREL The ISUP Release cause for a message that is determined to be circular routed. Default=31

Range = 0-255

Default Routing Number Default routing number. This parameter provides a set of digits to substitute for a signaling point.This parameter is used with both calling party and called party numbers. Default: 'None'

Range = a-f, A-F, 0-9 and Maximum Length = 15
DLMA Delimiter A. The digits used for Delimiter A in an NPP Formatting Action. Default='None'

Range = a-f, A-F, 0-9 and Maximum Length = 16
DLMB Delimiter B. The digits used for Delimiter B in an NPP Formatting Action. Default='None'

Range = a-f, A-F, 0-9 and Maximum Length = 16
DLMC Delimiter C. The digits used for Delimiter C in an NPP Formatting Action. Default='None'

Range = a-f, A-F, 0-9 and Maximum Length = 16
IAMCGPN The format of the outgoing CgPN digits. Default='Dn'

Range : 'Rn', 'Rndn', 'Dn'
MATCHSEQ The DN lookup mechanism. Default='Dn'

Range = 'Nptype', 'Dn'
NPFLAG This parameter specifies whether the nm parameter is modified in the IAM message to show that NP lookup has been performed. The nm parameter exists only in incoming and outgoing IAM messages. Default='None'

Range = 'None', 'Nm'
NPTYPECGPN NP entity type for the CgPN. The entity type of the DN that is used to indicate that a successful NP lookup occurred. Default='Sprn'

Range = 'Sp', 'Rn', 'Sprn', 'All', 'Rnspdn', 'Any'
NPTYPERLS The entity type of the DN that is used to indicate that a successful NP lookup occurred for the NPRLS and NPNRLS Service Actions. Default='Sprn'

Range = 'Sp', 'Rn', 'Sprn', 'All', 'Rnspdn', 'Any'
NPTYPERLY The entity type of the DN that is used to indicate that a successful NP lookup occurred for the NPRELAY Service Action. Default='Sprn' and Range = 'Sp', 'Rn', 'Sprn', 'All', 'Rnspdn', 'Any'
NSADDLDATA This parameter specifies whether the incoming IAM Calling Party Category should be compared with the value for the nspublic parameter before performing Calling Party number substitution. Default='No' and Range = 'Yes', 'No'
NSPUBLIC The value of the Calling Party Category that indicates that the Calling Party number is public. Default=0 and Range = 0-255
RCAUSENP The value used for the release cause in an REL message when number portability occurs. Default=0 and Range = 0-127
RCAUSEPFX The value used for the release cause in an REL message when number portability does not occur. Default=0 and Range = 0-127
RLCOPC This parameter specifies whether the value specified for the rcause parameter overrides the values specified for the rcausenp and rcausepfx parameters. Default='Off' and Range = 'Off', 'On'
RNRQD This parameter specifies whether the redirection number is included in the release message when release handling is indicated. Default='Yes' and Range = 'Yes', 'No'
SNSCGPNDFLT The digits to be used in calling number simple number substitution. Default='None' and Range = a-f, A-F, 0-9 and Maximum Length = 32
SPFILL This parameter specifies whether the sp entity type is populated if the value specified for the defltrn or grn parameter is used for NPP processing. Default='Off' and Range = 'Off', 'On'
SPLITIAM This parameter specifies when to split the IAM into IAM + 1 SAM. Default='None' and Range = 15-31
SUBCDPN Substitute CdPN, provides a set of digits to substitute for CdPN. Use this when SA is TIFRDNBL. [Default='None' and Range = a-f, A-F, 0-9 and Maximum Length = 10]

You can perform edit task on TIF Options page.

Editing a Common Screening List

Use this procedure to change the field values for a selected Common Screening List:
  1. Select the TIF Options row to be edited.
  2. Click Edit
  3. Enter the updated values.
  4. Click OK, Apply, or Cancel