IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.associatedVirtualCircuits(List<String> associatedVirtualCircuits) |
The list of virtual circuit
OCIDs over which
your network can reach this tunnel. |
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.bgpSessionInfo(BgpSessionInfo bgpSessionInfo) |
|
static IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.builder() |
Create a new builder.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.compartmentId(String compartmentId) |
The OCID of the
compartment containing the tunnel. |
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.copy(IPSecConnectionTunnel model) |
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.cpeIp(String cpeIp) |
The IP address of the CPE device’s VPN headend.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.displayName(String displayName) |
A user-friendly name.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.dpdMode(IPSecConnectionTunnel.DpdMode dpdMode) |
Dead peer detection (DPD) mode set on the Oracle side of the connection.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.dpdTimeoutInSec(Integer dpdTimeoutInSec) |
DPD timeout in seconds.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.encryptionDomainConfig(EncryptionDomainConfig encryptionDomainConfig) |
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.id(String id) |
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.ikeVersion(IPSecConnectionTunnel.IkeVersion ikeVersion) |
Internet Key Exchange protocol version.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.lifecycleState(IPSecConnectionTunnel.LifecycleState lifecycleState) |
The tunnel’s lifecycle state.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.natTranslationEnabled(IPSecConnectionTunnel.NatTranslationEnabled natTranslationEnabled) |
By default (the AUTO setting), IKE sends packets with a source and destination
port set to 500, and when it detects that the port used to forward packets has changed
(most likely because a NAT device is between the CPE device and the Oracle VPN headend)
it will try to negotiate the use of NAT-T.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.oracleCanInitiate(IPSecConnectionTunnel.OracleCanInitiate oracleCanInitiate) |
Indicates whether Oracle can only respond to a request to start an IPSec tunnel from the
CPE device, or both respond to and initiate requests.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.phaseOneDetails(TunnelPhaseOneDetails phaseOneDetails) |
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.phaseTwoDetails(TunnelPhaseTwoDetails phaseTwoDetails) |
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.routing(IPSecConnectionTunnel.Routing routing) |
The type of routing used for this tunnel (BGP dynamic routing, static routing, or
policy-based routing).
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.status(IPSecConnectionTunnel.Status status) |
The status of the tunnel based on IPSec protocol characteristics.
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.timeCreated(Date timeCreated) |
The date and time the IPSec tunnel was created, in the format defined by
RFC3339. |
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.timeStatusUpdated(Date timeStatusUpdated) |
When the status of the IPSec tunnel last changed, in the format defined by
RFC3339. |
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.toBuilder() |
|
IPSecConnectionTunnel.Builder |
IPSecConnectionTunnel.Builder.vpnIp(String vpnIp) |
The IP address of the Oracle VPN headend for the connection.
|