Specifications

Safety and Regulatory Certifications

For information regarding safety and regulatory certifications applicable to the Acme Packet 1100, refer to the Acme Packet Platforms Safety and Compliance Guide in addition to this chapter.

Acme Packet 1100 System Specifications

Table 6-1 Acme Packet 1100 System Specifications (cont.)

Specification	Description
Height	1.75 in (4.45 cm) (1U)
Width	11.25 in (28.57 cm)
Depth	8.48 in (21.54 cm)
Weight	4.0 lbs (1.81 kg)
Ports	Three 10/100 Mbps Ethernet copper ports (RJ-45 connector) dedicated to WAN, LAN, and management. One of the following: One or four T1/E1 ports for PSTN fallback Four FXO ports Four FXS ports
Onboard Transcoding & QoS Measurement Module	Hardware-assisted transcoding and QoS monitoring and reporting
Mounting	Table top Rack mount flanges for front/rear/center installation in 19/23 in racks (optional) Wall mount brackets (optional)
LEDs	Front: Ethernet link and activity status LEDs for PWR, NET MGT, INT, EXT, and OK Rear: Ethernet link and activity status LEDs for NET MGT, INT, EXT, and T1/E1 link status
Memory	4 GB for active configuration and logs 40 GB fast M-SATA drive for runtime image, backup configurations and local CDR backup
System Reset	Reset pinhole

Chassis Mounting Flanges Physical Specifications (Optional)

Table 6-2 Chassis Mounting Flange Physical Dimensions (cont.)

Specification	Description
Width	3.875 in (9.8425 cm) (each)

AC Power Supply Specifications

Table 6-3 AC Power Supply Specifications (cont.)

Specification	Fuse Rating
Voltage	Autoranging 100 AC to 240 AC wide input with power factor correction
Frequency	50/60 Hz
Current	12v x 0.75A
Cable	2.0 m 18 AWG three-wire cable with three-lead IEC 320 receptacle on the power supply end and a country-dependent plug on the power source end
Power	300 VA maximum
Type	External, field-replaceable

Power Supply Input Circuit Fuse Requirements

Table 6-4 Acme Packet 1100 Power Supply Input Circuit Fuse Requirements (cont.)

Power Circuit	Fuse Rating	Power cable size
120 VAC	15 AMP	18 AWG
240 VAC	7.5 AMP	18 AWG

Environmental Specifications

For the Acme Packet 1100 to function properly, Acme Packet recommends that you follow the environmental guidelines in the following table.

Table 6-5 Acme Packet 1100 Environmental Specifications (cont.)

Specification	Description
Temperature	The Acme Packet 1100 is required to operate within the temperature range of: 32° F to 104° F (+0° C to +40° C) (operating) -4° F to 149° F (-20° C to +65° C) (storage)
Relative Humidity	10% to 85%, non-condensing
Maximum Altitude	The Acme Packet 1100 System is required to operate below the maximum altitude of 10,000 feet.
Air Flow	Single fan: 2.2 CFM (3.6 CFM Max)
Power Dissipation	10 Watts (maximum)

Connector Specifications

Refer to the following table for information about the connector specifications for the Acme Packet 1100.

Table 6-6 Acme Packet 1100 Connector Specifications (cont.)

Specification	Description
RJ45/Management Ethernet Ports	The 3 x 8-pin RJ45 10/100 Ethernet ports are compliant with IEEE's 802.3, 802.3u, 802.1q and 802.3ab.
RS232/Serial Port	The RS232 serial port uses an 8-pin RJ45 connector that supports the RS232-C protocol.
IEC Connector Ports	The IEC connector ports accept a 3-lead IEC-320 connector for AC power installations.
RJ48C T1/E1 Port (Optional)	Mechanical Arrangement: Miniature 8-position jack. Usage: 1.544 Mbps digital services. Electrical Network Connection: T&R, T1 R1, conductors 7 and 8 provide cable shield integrity.