7 Specifications
This chapter provides information regarding the physical, electrical, environmental, and connector specifications of the Acme Packet 4600 System.
Environmental, Safety, and Regulatory Certifications
For information regarding safety and regulatory certifications applicable to the Acme Packet 4600, refer to the Acme Packet Platforms Safety and Compliance Guide.
Physical Specifications
Acme Packet 4600 System Chassis Specifications
This table lists the physical dimensions and weight of the Acme Packet 4600 chassis.
| Specification | Description |
|---|---|
| Height | 1.72” (4.37 cm) (1U) |
| Width | 17.10” (43.43 cm) (+ mounting ear width: 19” (43.18 cm)) |
| Depth | 20” (48.26 cm) (+ mounting slide bar depth) |
| Weight | approximately 20.5 lbs (9.30 kg), fully loaded |
AC Power Supply Physical Dimensions
This table lists the physical dimensions and weight of the Acme Packet 4600 AC power supply.
| Specification | Description |
|---|---|
| Height | 1.575” (4.00 cm) |
| Width | 2.146” (5.45 cm) |
| Depth | 13.26” (33.68 cm) |
| Weight | 2lbs., 5 oz. (1.05 kg) |
Note:
This equipment is intended for installation in locations where National Electrical Code (NEC) applies.
DC Power Supply Physical Dimensions
This table lists the physical dimensions and weight of the Acme Packet 4600 DC power supply.
| Specification | Description |
|---|---|
| Height | 1.575” (4.00 cm) |
| Width | 2.146” (5.45 cm) |
| Depth | 13.26” (33.68 cm) |
| Weight | 2lbs., 5 oz. (1.05 kg) |
Note:
This equipment is intended for installation in Network Telecommunication Facilities.Electrical Specifications
Refer to the following tables for information regarding the electrical specifications of the Acme Packet 4600 System.
Environmental Specifications
For the Acme Packet 4600 to function properly, Acme Packet recommends that you follow the environmental guidelines in the following table.
| Specification | Description |
|---|---|
| Temperature |
The Acme Packet 4600 is required to operate within the temperature range of: 0° C to +40° C, 32° F to 104° F (operating) -20° C to +65° C, -4° F to 149° F (storage) |
| Relative Humidity | Operating conditions of 10% to 85% humidity under non-condensing operating conditions |
| Maximum Altitude | The Acme Packet 4600 is required to operate below the maximum altitude of 10,000 feet. |
| Air Flow | 50 CFM front to back |
| Power Dissipation | 250W typical 350W maximum (base system with 2 x 10GbE NIU) |
Connector Specifications
Refer to the following table for information about the connector specifications for the Acme Packet 4600.
| Specification | Description |
|---|---|
| AC Connector Port | The IEC lead connector port on each power supply accepts a 3-lead IEC-60320 C14 connector for AC power installations (2). |
| RJ45/Management Ethernet Ports | The 3 x 8-pin RJ45 10/100/1000BaseT ports are compliant with IEEE's 802.3, 802.3u, and 802.3ab. |
| RJ45/Alarm Contact Port | Any alarms generated by the system are accessible via the 8-pin RJ45 alarm contact port. |
| RS232/Serial Port | The RS232 serial port uses an 8-pin RJ45 connector that supports RS232 protocol. |
| 1 GbE/10GbE Port(s) | The four 1 GbE fiber optic connection ports (P0-P3) and the two 10GbE fiber optic connection ports (P4-P5) use duplex LC connectors (2). |
| Terminal Block Connections | The terminal block connections accept a bare (tinned) wire for DC power installations on each DC power supply (2). |
Optical Transceiver Interface Module Specification
Refer to the following table for information about the optical specifications of the optical transceivers for the Acme Packet 4600.
| Specification | Single Mode (SX) Fiber Module | Multi Mode (LX) Fiber Module |
|---|---|---|
| Wavelength λ | 1310 nm | 850 nm |
| Laser Type | VCSEL | VCSEL |
| Fiber type / Transmission Distance |
0.5 to 550 m — 50 μm MMF 0.5 to 550 m — 62.5 μm MMF |
300 m |