4.69 chg-gtmod

Use this command to change GT Modification (GTMOD) entry data. The GTMOD entry consists of a GTMOD ID and GTMOD specific data.

Parameters

Note:

Definitions for the feature options specified by the on and off parameters are located in the Notes section.
gtmodid (mandatory)
GT Modification Identifier.
Range:
ayyyyyyyy

1 alphabetic character followed by up to 8 alphanumeric characters

cgpassn (optional)
Calling party subsystem number. This parameter specifies the calling party subsystem address that receives the message.
Range:
2 - 255, none
Default:
No change to the current value
ngti (optional)
New Global Title Indicator. This parameter specifies whether a new GTI translation format is type 2 or type 4.
Range:
2
4
none
Default:
No change to the current value
ngtmodid (optional)
New GT Modification Identifier.
Range:
ayyyyyyyy

1 alphabetic character followed by up to 8 alphanumeric characters

nnai (optional)
New nature of address indicator. This parameter specifies the value that is used to replace the received NNAI.
Range:
0 - 127, none
Default:
none-if the ngti=2 parameter is specified. Otherwise, no change to the current value.
nnp (optional)
New numbering plan. The value used to replace the received numbering plan.
Range:
0 - 15, none
Default:
none-if the ngti=2 parameter is specified. Otherwise, no change to the current value.
npdd (optional)
Number of prefix digits to be deleted. The number of digits to be deleted from the prefix of the received GT address.
Range:
1 - 21, none
Default:
No change to the current value
npds (optional)
New prefix digits string. The digits to be prefixed to the received GT address.
Range:
1-21 digits, none

If the Hex Digit Support for GTT feature is not enabled, the range is 1 - 21 decimal digits; valid digits are 0-9.

If the Hex Digit Support for GTT feature is on, the range is 1 - 21 hexadecimal digits; valid digits are 0-9, a-f, A-F.

Default:
No change to the current value
nsdd (optional)
Number of suffix digits to be deleted. The number of digits to be deleted from the suffix of the received GT address.
Range:
1 - 21, none
Default:
No change to the current value
nsds (optional)
New suffix digits string. The digits to be suffixed to the received GT address.
Range:
1-21 digits, none

If the Hex Digit Support for GTT feature is not enabled, the range is 1 - 21 decimal digits; valid digits are 0-9.

If the Hex Digit Support for GTT feature is enabled and on, the range is 1 - 21 hexadecimal digits; valid digits are 0-9, a-f, A-F.

Default:
No change to the current value
ntt (optional)
New Translation Type. The value that replaces the received Translation Type.
Range:
0 - 255, none
Default:
No change to the current value
off (optional)

Turns off the specified feature options. A comma-separated list of feature options that are requested to be turned off. Up to 8 feature options can be specified in the list.

Range:
gt0fill
on (optional)

Turns on the specified feature options. A comma-separated list of feature options that are requested to be turned on. Up to 8 feature options can be specified in the list.

Range:
gt0fill
precd (optional)
Precedence. This parameter specifies whether the prefix or suffix takes precedence during modification of the received GT address.
Range:
pfx
sfx
Default:
pfx-if the npdd and npds  parameters are specified

sfx-if the nsdd and nsds parameters are specified

Example

chg-gtmod:gtmodid=set2:ngti=4:nnp=4:nnai=2:off=gt0fill:npds=2:precd=sfx:nsds=1

chg-gtmod:gtmodid=set3:on=gt0fill:nnp=7:nnai=100:nsdd=2:ntt=none

Dependencies

If the ngti=4 parameter is specified, then the nnp and nnai parameters must be specified.

If the ngti=2 parameter is specified, then the nnp and nnai parameters cannot be specified.

The ANSI/ITU SCCP Conversion feature must be enabled before the ngti parameter can be specified.

The Hex Digit Support for GTT feature must be turned on before hexadecimal digits can be specified for the npds or nsds parameter.

The GTMOD table is corrupt or cannot be found.

At least one optional parameter must be specified.

The AMGTT, AMGTT CdPA Only, or AMGTT CgPA Upgrade feature must be turned on before any parameter except the ntt parameter can be specified.

The value specified for the gtmodid parameter must already exist in the GTMOD table.

If the npdd/npds and nsdd/nsds parameters are specified or were previously provisioned, then the precd parameter must be specified.

The combined digit length of the values for the specified or previously provisioned npds  and nsds parameters cannot be greater than 21.

The (n)gtmodid=none parameter cannot be specified.

If the ngti=4 parameter is specified, then the referred translated point code cannot be ANSI. For ANSI point codes, the ngti value must be 2.

If the ngti=4 parameter is specified or was previously provisioned, then a value of none cannot be specified for the nnp and nnai parameters.

If the ngti=none parameter is specified, then the on=gt0fill parameter cannot be specified.

If the on=gt0fill parameter is specified, then the ngti parameter must be specified.

The value specified for the ngtmodid parameter cannot already exist in the database.

The same value cannot be specified for the on and off parameters.

Notes

on/off options

  • gt0fill —GT zero fill. Specifies whether the last 0 of the GTA is a treated as a valid digit (OFF) or as filler (ON) during GT Modification for the gti(x)=2 to gti(x)=4 scenario.

Output

chg-gtmod:gtmodid=gtmodid2:ngti=4:nnp=4:nnai=2:off=gt0fill 

    tekelecstp 10-03-18 14:43:31 EST  EAGLE 42.0.0
    Command entered at terminal #4

    GTMOD table is (2 of 50000) 1% full

    CHG-GTMOD: MASP A - COMPLTD 
;

Related Topics