4.99 chg-m2pa-tset

Use this command to change M2PA timers in an M2PA timer set. The srcset and tset parameters can be used to copy from one timer set to another.

Note:

The M2PA RFC feature introduces 20 new timer sets. M2PA timer sets created prior to this feature become M2PA Draft 6 timer sets, which are used by the M2PA Draft 6 associations. M2PA RFC associations use the RFC timer sets.

Parameters

Note:

All values specified for the timer parameters (t(X)) are in milliseconds.
tset (mandatory)
Timer set. The name of the M2PA timer set.
Range:
1 - 20
srctset (optional)

The timer set to be copied into the timer set specified by the tset parameter. If this parameter is specified, no other timer values can be specified.

Range:
1 - 20
t1 (optional)
T1 timer. Alignment timer. The amount of time M2PA waits to receive a Link Status Alignment message from the peer.
Range:
1000 - 350000
Default:
D6- 10000

RFC- 35000

t2 (optional)
T2 timer. M2PA RFC timer.

Note:

This timer is not used in M2PA Draft 6 timer sets.
Range:
5000 - 150000
Default:
20000
t3 (optional)
T3 timer. Ready timer. The amount of time after proving that M2PA waits to receive a Link Status Ready message from the peer.
Range:
1000 - 60000
Default:
10000 D6

2000 RFC

t4e (optional)
T4E timer. Emergency proving timer. The amount of time M2PA generates Link Status Proving messages during emergency proving.
Range:
400 - 5000
Default:
500
t4n (optional)
T4N timer. Normal proving timer. The amount of time M2PA generates Link Status Proving messages during normal proving.
Range:
1000 - 70000
Default:
D6- 10000

RFC- 30000

t5 (optional)
T5 timer. Busy rate timer. The amount of time between sending Link Status Busy messages while the link is in service.
Range:
80 - 10000
Default:
1000 D6

100 RFC

t6 (optional)
T6 timer. Remote congestion timer. The amount of time that a congested link will remain in service.
Range:
1000 - 6000
Default:
3000
t7 (optional)
T7 timer. Excessive acknowledgement delay timer. The maximum amount of time that can pass between transmission of a user data message and receipt of an acknowledgement for that message from the peer. If this timer expires, the link is taken out of service.
Range:
200 - 2000
Default:
1200
t16 (optional)
T16 timer. Proving rate timer. The amount of time between sending Link Status Proving messages while T2N or T2E is running.

Note:

The T16 value is given in microseconds.
Range:
100 - 500000
Default:
200000
t17 (optional)
T17 timer. Ready rate timer. The amount of time between sending Link Status Ready messages while T3 is running.
Range:
100 - 500
Default:
250
t18 (optional)
T18 timer. Processor outage rate timer. The amount of time between sending Link Status Processor Outage messages while the link is in service.
Range:
100 - 10000
Default:
1000
ver (optional)
Version. The M2PA version used by the association.
Range:
d6
rfc

Example

chg-m2pa-tset:tset=1:t1=20000

chg-m2pa-tset:tset=1:t1=20000:ver=d6

chg-m2pa-tset:srctset=1:tset=2:ver=rfc

Dependencies

At least one optional parameter must be specified.

The srctset parameter and the tset parameter cannot specify the same timer set name.

The specified timer must be supported for the Draft 6 version of M2PA.

Either a timer value or the srctset parameter must be specified.

Timer value parameters and the SRCTSET parameter cannot be specified together.

Notes

None

Output

chg-m2pa-tset:tset=1:t1=20000:ver=d6

    rlghncxa03w 06-01-18 08:16:14 EST  EAGLE 34.3.0
    CHG-M2PA-TSET:  MASP A - COMPLTD 
;

Related Topics