4.111 chg-ppsopts

Use this command to enter Prepaid Short Message Service options (PPSOPTS) in the database. This command updates the PPSOPTS Table with entries that correspond to Intelligent Network (IN) platforms.

Parameters

Note:

See Point Code Formats and Conversion for a detailed description of point code formats, rules for specification, and examples.

Note:

If the CgPA GTA matches the value of the gta, gta1, gta2, or gta3 parameter during message screening, then the message falls through to GTT instead of receiving PPSMS screening.
bpartychk (optional)
MO SMS B-Party PPSMS Check. This parameter specifies whether a prepaid check on the B-Party is performed on an incoming MO SMS message.
Range:
off
Prepaid Check on B-Party is not performed
on
Prepaid Check on B-Party is performed
Default:
No change to current value
System Default:
off
gta (optional)
Global title address. The entity address for an IN platform. Determines whether an incoming message receives PPSMS screening.
Range:
1-15 digits

Valid digits are 0-9, A-F, a-f.

Default:
No change to current value
gta1 (optional)
Global title address. The entity address for an IN platform. Determines whether an incoming message receives PPSMS screening.
Range:
1-15 digits

Valid digits are 0-9, A-F, a-f

Default:
No change to current value.
gta2 (optional)
Global title address. The entity address for an IN platform. Determines whether an incoming message receives PPSMS screening.
Range:
1-15 digits

Valid digits are 0-9, A-F, a-f

Default:
No change to current value.
gta3 (optional)
Global title address. This parameter specifies the entity address for an IN platform. Determines whether an incoming message receives PPSMS screening.
Range:
1-15 digits

Valid digits are 0-9, A-F, a-f

Default:
No change to current value.
ngta (optional)
New global title address. An entity address that replaces an existing entity address for an IN platform.
Range:1-15 digits, none

Valid digits are 0-9, A-F, a-f

none —Deletes the current value

Default:
No change to current value.
pc (optional)
ANSI point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm). The prefix subfield indicates a private point code (prefix-ni-nc-ncm).
Synonym:
pca
Range:

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

p-, 000-255, none

prefix—p-

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid for ni = 001-005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006-255.

Enter none to delete the point code.

The point code 000-000-000 is not a valid point code.

Default:
No change to current value.
pci (optional)
ITU international point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
Range:
s-, 0-255, none

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s

zone—0-7

area—000-255

id—0-7

Enter none to delete the point code.

The point code 0-000-0 is not a valid point code.

Default:
No change to current value.
pcn (optional)
ITU national point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the chg-stpopts:npcfmti flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
Range:
s-, 0-16383, aa-zz, none

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

Enter none to delete the point code.

Default:
No change to current value.
ppt (optional)
Prepaid portability type. The IN platform where the incoming message is sent.
Range:
1 - 32
ri (optional)
Routing indicator. The IN platform routing indicator.
Range:
gt
Routes on the GT value.
ssn
Routes on the SSN value.
Default:
No change to current value.
setid (optional)
Set ID. The MAP set ID (if the ri=ssn parameter is specified) or the MRN set ID (if the ri=gt parameter is specified) that is used by a loadsharing IN platform.

Note:

If the FGTTLS feature is not enabled, lookup is performed in the default set of the MAP table or MRN table.
Range:
1 - 36000, none, dflt

1 - 36000, none, dflt —MAP table

1 - 3000 —MRN table

none —Lookup is not performed. This value applies only to the MRN table.

dflt —Lookup is performed in the default MAP set or MRN set.

Default:
No change to current value.
ssn (optional)
Subsystem number
Range:
2 - 255
Default:
none

Example

This command provisions a single GTA in the PPSOPTS table.

chg-ppsopts:gta=1234

This command provisions four GTAs in the PPSOPTS table.

chg-ppsopts:gta=1101:gta1=1102:gta2=1103:gta3=1104

This command replaces an existing GTA with a new GTA.

chg-ppsopts:gta=1101:ngta=4567

This command deletes a specified GTA from the PPSOPTS table.

chg-ppsopts:gta=1102:ngta=none

This command deletes the pc, ri, and setid values for a specified IN platform.

chg-ppsopts:ppt=1:pci=none

This example provisions a loadsharing set for a specified IN platform.

chg-ppsopts:ppt=2:setid=2

This example provisions point code, routing indicator, and set ID values for a specified IN platform and loadsharing set.

chg-ppsopts:ppt=1:pci=1-1-1:ri=gt:setid=1

This example provisions the prepaid check on B-Party.

chg-ppsopts:bpartychk=on

This example provisions ANSI point code, routing indicator, and set ID values for a specified IN platform and loadsharing set.

chg-ppsopts:ppt=2:pca=2-2-1:ri=ssn:setid=4

Dependencies

At least one parameter must be specified.

The PPSMS, IDP A-Party Routing, or IDP Service Key Routing feature must be enabled and turned on before this command can be entered.

If the ngta parameter is specified, then the gta parameter must be specified.

The gta, gta1, gta2, and gta3 parameters cannot have a value of none.

If the ngta parameter is specified, the gta parameter value must already exist in the database.

The ngta parameter value cannot already exist in the database.

The value specified for the pc/pca/pci/pcn parameter cannot be the same as the STP True Point Code.

The value specified for the pc/pca/pci/pcn parameter cannot be the same as the STP Capability Point Code.

If the pc, ri, ssn, or setid parameter is specified, then the ppt parameter must be specified.

If the gta1, gta2, or gta3 parameter is specified, then the ngta parameter cannot be specified.

The Flexible GTT Load Sharing (FGTTLS) feature must be enabled before the setid parameter can be specified.

If the ri=gt parameter is specified, then the value of the setid parameter cannot exceed the value of the maximum MRN set ID.

The Site Identification table is corrupt or cannot be found.

The value specified for the pc/pca/pci/pcn parameter must already exist in the Routing Indicator table.

The Prepaid SMS options (PPSOPTS) table is corrupt or cannot be found.

The value of the gta, gta1, gta2, or gta3 parameter cannot already exist in the database unless the ngta parameter is specified.

The pc/pca/pci/pcn parameter and the ri parameter must be specified together in the command, or a value of none must be specified for the pc/pca/pci/pcn parameter.

The gta, gta1, gta2, and gta3 parameters cannot have the same value.

A maximum of 32 GTA values (for 32 IN platforms) can be defined in the database.

If the Flexible GTT Load Sharing (FGTTLS) feature is enabled, and if the ri=ssn parameter is specified, then the values specified for the pc/pca/pci/pcn and ssn parameters must exist in the MAP table in the MAP set specified by the setid parameter, or in the default MAP set if the setid parameter is not specified.

If the ri=gt parameter is specified, then the value specified for the pc/pca/pci/pcn parameter must exist in the MRN table.

If the ri=ssn parameter is specified, then the setid=none parameter cannot be specified.

The pc/pca/pci/pcn, ri, setid, and ssn parameters must be specified before the ppt parameter can be specified.

The pc/pca/pci/pcn parameter must be provisioned for the prepaid type specified by the ppt parameter before the setid parameter can be specified.

If a value of none is specified for the pc/pca/pci/pcn parameter, then the ri or setid parameter cannot be specified.

If the Flexible GTT Load Sharing (FGTTLS) feature is not enabled, and if the ri=ssn parameter is specified, then the value specified for the pc/pca/pci/pcn parameter must exist in the default MAP set of the MAP table.

The value specified for the pc/pca/pci/pcn parameter cannot be associated with a proxy point code.

If the ssn parameter is specified, then the pc/pca/pci/pcn parameter must be specified.

The MRN table is corrupt or cannot be found.

Notes

The spare point code subtype prefix (s-) is supported only for ITU international and ITU national point codes.

The GTA digits are used during message screening to determine whether an incoming message should receive PPSMS screening. If the CgPA GTA matches the value of any of the GTA parameters, then the message falls through to GTT instead of receiving PPSMS screening.

The point code and routing indicator values (pc/pca/pci/pcn and ri parameters) are used to route messages from prepaid subscribers to the correct IN for credit checking.

Output

chg-ppsopts:ppt=1:pci=1-1-1:ri=gt:setid=1

    tekelecstp 06-06-25 09:04:14 EST  EAGLE 37.0.0
    CHG-PPSOPTS: MASP A - COMPLTD 
;

Related Topics