4.115 chg-sccp-msg
Use this command to revise an SCCP message.
Parameters
Note:
The nature of address indicator, numbering plan, and TCAP package indicator can be specified by mnemonic or numeric values (cdnai/cdnaiv, cdnp/cdnpv, and tcappkg/tcappkgv respectively).- active (optional)
- This parameter specifies whether the SCCP message should be sent to the network card for processing.
- cdnaiv (optional)
- CdPA NAIV. The Called Party Nature of Address Indicator Value for the SCCP message.
- cdpc (optional)
-
ANSI Called Party point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm).
- Range:
- p-, 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
When
chg-sid:pctype=ansi
is specified, ni = 000 is not valid.When
chg-sid:pctype=ansi
is specified, nc = 000 is not valid if ni = 001-005.When
chg-sid:pctype=ansi
is specified, nc = 000 is valid if ni = 006-255.The point code 000-000-000 is not a valid point code.
- Default:
- 10
- cdpci (optional)
- ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).
- cdpcn (optional)
- ITU national point code in the format of a 5-digit
number (nnnnn); or 2, 3,
or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by
the
chg-stpopts:npcfmti
flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- cdpcn24 (optional)
- 24-bit ITU national CdPA point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
- cdpcn16 (optional)
- 16-bit ITU national CdPA point code with subfields unit number-sub number area-main number area (un-sna-mna).
- cgnaiv (optional)
- CgPA NAIV. The Calling Party Nature of Address Indicator Value for the SCCP message.
- cgpc (optional)
-
ANSI CGPA point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm).
- Range:
- p-, 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
When
chg-sid:pctype=ansi
is specified, ni = 000 is not valid.When
chg-sid:pctype=ansi
is specified, nc = 000 is not valid if ni = 001-005.When
chg-sid:pctype=ansi
is specified, nc = 000 is valid if ni = 006-255.The point code 000-000-000 is not a valid point code.
- Default:
- 20
- cgpci (optional)
- ITU international CgPA point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- cgpcn (optional)
- ITU national CgPA point code in the format of a
5-digit number (nnnnn);
or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by
the
chg-stpopts:npcfmti
flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- cgpcn24 (optional)
- 24-bit ITU national CgPA point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
- cgpcn16 (optional)
- 16-bit ITU national CgPA point code with subfields unit number-sub number area-main number area (un-sna-mna).
- dpc (optional)
- ANSI destination point code with subfields
network
indicator-network cluster-network cluster member (ni-nc-ncm).
- Synonym:
- dpca
- Range:
- p-, 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
When
chg-sid:pctype=ansi
is specified, ni = 000 is not valid.When
chg-sid:pctype=ansi
is specified, nc = 000 is not valid if ni = 001-005.When
chg-sid:pctype=ansi
is specified, nc = 000 is valid if ni = 006-255.The point code 000-000-000 is not a valid point code.
- Default:
- 20
- dpci (optional)
- ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- dpcn (optional)
- ITU national destination point code in the format
of a 5-digit number (nnnnn); or 2, 3, or 4
numbers (members) separated by dashes (m1-m2-m3-m4) as defined by
the
chg-stpopts:npcfmti
flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- dpcn24 (optional)
- 24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
- dpcn16 (optional)
- 16-bit ITU national destination point code with subfields unit number-sub number area-main number area (un-sna-mna).
- imeidgts (optional)
- IMEI Digits. This specifies the IMEI digits present in the TCAP portion of the incoming MSU.
- imsidgts (optional)
- IMSI Digits. This specifies the IMSI digits present in the TCAP portion of the incoming MSU.
- mapparam (optional)
- MAP Parameters. The parameter defines the MAP parameters (IMEI/IMSI/MSISDN/VLR/SMRPOA/SMRPDA) present in the incoming MSU.
- msisdndgts (optional)
- MSISDN Digits. This specifies the MSISDN digits present in the TCAP portion of the incoming MSU.
- opc (optional)
-
ANSI originating point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm).
- Range:
- p-, 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
When
chg-sid:pctype=ansi
is specified, ni = 000 is not valid.When
chg-sid:pctype=ansi
is specified, nc = 000 is not valid if ni = 001-005.When
chg-sid:pctype=ansi
is specified, nc = 000 is valid if ni = 006-255.The point code 000-000-000 is not a valid point code.
- Default:
- 10
- opci (optional)
- ITU international originating point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- opcn (optional)
- ITU national originating point code in the format
of a 5-digit number (nnnnn); or 2, 3, or 4
numbers (members) separated by dashes (m1-m2-m3-m4) as defined by
the
chg-stpopts:npcfmti
flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- opcn24 (optional)
- 24-bit ITU national originating point code with
subfields
main signaling
area-sub signaling area-signaling point (msa-ssa-sp).
- Range:
-
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
p-, 000-255, none
prefix—p-
When
chg-sid:pctype=ansi
is specified, ni = 000 is not valid.When
chg-sid:pctype=ansi
is specified, nc = 000 is not valid for ni = 001-005.When
chg-sid:pctype=ansi
is specified, nc = 000 is valid if ni = 006-255.Enter none to delete the point code.
The point code 000-000-000 is not a valid point code.
- opcn16 (optional)
- 16-bit ITU national originating point code with subfields unit number-sub number area-main number area (un-sna-mna).
- smrpdadgts (optional)
- SMRPDA Digits. The digits present in the SMRPDA parameter of the incoming MSU.
- smrpoadgts (optional)
- SMRPOA Digits. The digits present in the SMRPOA parameter of the incoming MSU.
- tcapopcodetag (optional)
- The first ITU TCAP opcode field in the incoming MSU. .
- Range:
- local, global, none, notpresent
local —The opcodetag is local(opcodetag=2) in the ITU TCAP opcodetag field in the incoming MSU.
global —The opcodetag is global(opcodetag=6) in the ITU TCAP opcodetag field in the incoming MSU.
none—the first component is present but there is no opcode in it
notpresent—the first component is not present
- Default:
- notpresent
- tcapopcode3 (optional)
- The third TCAP opcode field in the incoming MSU.
- Range:
- local, global, none, notpresent
local — The opcodetag is local(opcodetag=2) in the ITU TCAP opcodetag field in the incoming MSU.
global — The opcodetag is global(opcodetag=6) in the ITU TCAP opcodetag field in the incoming MSU.
none—the third component is present but there is no opcode in it
notpresent—the third component is not present
- Default:
- notpresent
- tcappkg (optional)
- TCAP package. The ANSI TCAP and ITU TCAP package
type.
- Range:
-
- ituuni
- ITU unidirectional
- qwp
- Query with Permission
- qwop
- Query without Permission
- resp
- Response
- cwp
- Conversation with Permission
- cwop
- Conversation without Permission
- bgn
- Begin
- end
- End
- cnt
- Continue
- ituabort
- ITU abort
- ansiabort
- ANSI abort
- ansiuni
- ANSI unidirectional
- ANSI TCAP Package Types—
- ansiuni, qwp, qwop, resp, cwp, cwop, ansiabort
- ITU TCAP Package Types—
- bgn, ituabort, ituuni, end, cnt
Example
chg-sccp-msg:msgn=1:cgtt=4:cdnp=generic:eaglegen=yes:cdpc=2-2-2
chg-sccp-msg:msgn=3:cdgta=324ab12:cdtt=6:cdnaiv=3:cgnai=rsvd
chg-sccp-msg:msgn=5:cdtt=10:opc=4-5-6:cgpcn=1234
chg-sccp-msg:msgn=1:tcappkg=bgn:tcapopcode=34
chg-sccp-msg:msgn=1:cdtt=12:dpci=1-101-1:cgpci=1-101-2
chg-sccp-msg:msgn=5:cdtt=10:opcn16=2-14-0:cgpcn16=2-14-1
chg-sccp-msg:msgn=1:smrpoadgts=654789:smrpdanp=e164:smrpoanp=x121:
imsidgts=123456
chg-sccp-msg:msgn=1:tcapopcode=34:tcapopcode2=35:tcapopcode3=100
chg-sccp-msg:msgn=1:tcapopcode=local:tcapopcodetag2=local:tcapopcodetag3=none
Dependencies
The TSTMSG table is corrupt or cannot be found.
At least one optional parameter must be specified.
The cdnp and cdnpv parameters and the cgnp and cgnpv parameters cannot be specified together in the command.
The cdnai and cdnaiv parameters and the cgnai and cgnaiv parameters cannot be specified together in the command.
A TOBR quantity feature must be turned on before the tcapacn, tcappkg, tcappkgv, tcapopcode,tcapopcode2, tcapopcode3 , tcapopcodetag, tcapopcodetag2, tcapopcodetag3, tcapfamily, tcapfamily2, tcapfamily3, mapparam, imsidgts, imeidgts, msisdndgts, vlrdgts, smrpoadgts, smrpdadgts, msisdnnp, smrpoanp or smrpdanp parameter can be specified.
The tcappkg and tcappkgv parameters cannot be specified together in the command.
The values 1 and 3 cannot be specified for the cdgti and cggti parameters.
The GTT feature must be turned on before this command can be entered.
The J7 Support feature must be enabled before the cgpcn16/cdpcn16/opcn16/dpcn16 parameters can be specified.
Tcapopcode2 cannot be 0-255 or none if tcapopcode = notpresent, and tcapopcode3 cannot be 0-255 or none if tapopcode2 = notpresent.
tcapopcodetag2 cannot be local, global or none if tcapopcodetag = notpresent, and tcapopcodetag3 cannot be local, global or none if tcapopcodetag2 = notpresent.
2155 E2155 Cmd Rej: Invalid parameter combination specified
tcapopcodetag cannot be local, global or none if tcapopcodetag = notpresent, and tcapopcodetag2 cannot be local, global or none if tcapopcodetag2 = notpresent, and tcapopcodetag3 cannot be local, global or none if tcapopcodetag3 = notpresent.
2155 E2155 Cmd Rej: Invalid parameter combination specified
Notes
There is no J7 FAK dependency on ANSI/N24 point code parameters, i.e., cgpcn24/cdpcn24/opcn24/dpcn24/cgpca/cdpca/opca/dpca. The command can be entered successfully whether or not the J7 Support feature is enabled.
Output
chg-sccp-msg:msgn=1:tcapacn=7-8-9-0
tekelecstp 09-03-02 16:07:33 EST EAGLE 41.0.0
Command entered at terminal #4.
CHG-SCCP-MSG: MASP A - COMPLTD
;
chg-sccp-msg:msgn=1:smrpoadgts=654789:smrpdanp=e164:smrpoanp=x121:imsidgts=123456
tekelecstp 15-06-01 16:07:33 EST EAGLE 46.3.0
Command entered at terminal #4.
CHG-SCCP-MSG: MASP A - COMPLTD
;
chg-sccp-msg:msgn=1:tcapopcode=34:tcapopcode2=35:tcapopcode3=100
tekelecstp 16-10-03 14:18:10 MST EAGLE 46.5.0.0.0
Command entered at terminal #17.
CHG-SCCP-MSG: MASP A - COMPLTD
;
chg-sccp-msg:msgn=1:imeidgts=98715123450
tekelecstp 17-05-11 15:09:18 EST EAGLE 46.6.0
Command entered at terminal #4.
CHG-SCCP-MSG: MASP A - COMPLTD
;
Related Topics