4.346 ent-scr-tt

Use this command to add a specific allowed translation type (TT) screening reference in the TT entity set.

Parameters

nsfi (mandatory)
This parameter specifies the next screening category that is used in the gateway screening process, or it indicates that the gateway screening process should stop.
Range:
cdpa
Allowed CDPA is the next screening category.
stop
The gateway screening process ends and the message proceeds through normal routing.
sr (mandatory)
Screening reference. The point code’s unique screening reference name.
Range:
ayyy

1 alphabetic character followed by up to 3 alphanumeric characters

type (mandatory)
Translation type. The GTT type value in the CdPA. This value is the decimal representation of the 1-byte field used in SS7.
Range:
000 - 255, *

*—full range of values from 0-255

actname (optional)
The name of the gateway screening stop action set. Stop actions must be administered using this parameter in conjunction with the gateway screening stop action table (see chg-gws-actset and rtrv-gws-actset ).
Range:
ayyyyy

1 alphabetic character followed by up to 5 alphanumeric characters.

nsr (optional)
Next screening reference. This parameter indicates which screening reference in the specified screening category (nsfi) is to be used in the screening process.
Range:
ayyy

1 alphabetic character followed by up to 3 alphanumeric characters

Default:
No value given

Example

ent-scr-tt:sr=iec:type=012:nsfi=cdpa:nsr=wrd5

ent-scr-tt:sr=iec:type=012:nsfi=stop:actname=copy

Dependencies

Caution:

Even though gateway screening is in the screen test mode, as defined by the gwsa=off and gwsm=on parameters, the gateway screening action in the stop action set specified by the actname parameter of the screen set will be performed at the end of the screening process.

If the screening reference is valid, but does not exist, a new TT screen is created.

If the screening reference exists, a new rule is added to the TT screening table.

An asterisk cannot not be specified for a parameter value in this command unless an asterisk was specified for the parameter value in the original ent-scr-tt command.

If the actname parameter is specified, the nsfi=stop parameter must be specified.

The value of the actname parameter must already be defined in the Gateway Screening Stop Action table with the chg-gws-actset command.

If the nsfi=stop parameter is specified, the nsr parameter cannot be specified.

If the nsfi parameter has a value other than stop, the nsr parameter must be specified.

If the nsr parameter is specified, the specified screening reference must exist.

If the screening reference (sr) exists, the single value or range specified for the allowed type to be added to the TT screen for the allowed TT screening reference must not already exist in that TT screen.

If an asterisk is specified for the allowed type, nothing can already exist in the TT screen for the screening reference.

The Gateway Screening Stop Action table is corrupt or cannot be found.

The specified value for the nsfi parameter is not valid for TT screen.

The screen referenced by sfi and nsr must already exist.

The Gateway Screening Rules table can contain a maximum of 360,600 rules.

The value specified for the type parameter must be within the allowed range.

The GWSOA parameter combination should be known and valid.

Notes

If the screen set reaches 100% capacity (indicated by the 100% Full message), the system will allow subsequent entries. An error will occur, however, when downloading the screen set to a LIM. Screen sets should not exceed 100% capacity. Remove screen set entries until the capacity is below 100%.

Output

ent-scr-tt:sr=iec:type=012:nsfi=cdpa:nsr=wrd5 

    rlghncxa03w 04-01-07 11:43:04 EST  EAGLE 31.3.0
    ENT-SCR-TT:  SCREEN SET AFFECTED - IEC  25% FULL
    ENT-SCR-TT:  MASP A - COMPLTD 
;

Related Topics