4.355 ent-srvsel

Use this command to assign the applicable service selectors required to specify a service entry for DSM services.

Parameters

Note:

Definitions for the feature options specified by the on and off parameters are located in the Notes section.

Note:

The nature of address indicator parameters (naiv or nai) and the numbering plan parameters (npv or np) can be specified using a mnemonic or an explicit value. Either the mnemonic or the explicit value can be specified; however, both values cannot be specified at the same time for the same parameter. Table A-7 shows the mapping between the naiv and nai values. Table A-8 shows the mapping between the npv and np values.
gti/gtia/gtii/gtin/gtin24 (mandatory)
Global title indicator. For all service selector commands, the domain is defined as GTI and GTIA (ANSI), GTI (ITU international), and GTIN (ITU national). For the service selector commands, GTI and GTIA are equivalent.
Range:
Supported value for ANSI: gti=2 and gtia=2

Supported values for ITU: gtii= 0, 2, 4; gtin=0, 2, 4; gtin24= 0, 2, 4

serv (mandatory)
DSM service.

Note:

The gport service cannot be used for the Prepaid SMS Intercept Phase 1 (PPSMS) or the Portability Check for Mobile Originated SMS feature; use the smsmr service. The mnp service includes the G-Port, A-Port, and IS41 GSM Migration services.
Range:
eir
Equipment Identity Register
gflex
GSM flexible numbering
gport
GSM number portability
inpq
INP query
inpmr
INP message relay
smsmr
MO SMS ASD, MO SMS B-Party Routing, MO SMS GRN, MO-based GSM SMS NP, MO-based IS41 SMS NP, MO SMS IS41-to-GSM Migration, Portability Check for MO SMS, Prepaid SMS Intercept Phase 1
idps
IDP Screening for Prepaid
idpr
Prepaid IDP Query Relay
mnp
Mobile Number Portability
vflex
Voice Mail Router
atinp
ATI Number Portability Query (ATINP) 
ttr
Triggerless TCAP Relay
aiq
ANSI41 Analyzed Information Query
ssn (mandatory)
Subsystem number.
Range:
0 - 255
tt (mandatory)
Translation type.
Range:
0 - 255
dfltact (optional)

This parameter specifies the default Action ID associated with the service selector entry.

Range:
ayyyyyyyy

1 leading alphabetic followed by up to 8 alphanumeric characters

The dfltact parameter can have one of the following values:

  • a GTT Action ID that exists in the GTT Action table and has an associated GTT Action of disc/udts/tcaperr
  • fallback —Fallback to the Relay data. The relayed MSU is routed as per routing data provided by the service.
  • falltogtt —Fallback to GTT. If the gttselid parameter has a value other than none, and the GTT selector search fails, then the GTT selector search is performed again using gttselid=none.
Default:
fallback
gttselid (optional)
The GTT Selector ID used for performing GTT on messages relayed by the service.  
Range:
0 - 65534
nai (optional)
Nature of Address indicator.
Range:
sub
rsvd
natl
intl
naiv (optional)
Nature of Address indicator value.
Range:
0 - 127
np (optional)
Numbering Plan.
Range:
e164
generic
x121
f69
e210
e212
e214
private
npv (optional)
Numbering Plan value.
Range:
0 - 15
off (optional)
Disables or turns off the specified feature options. A comma-separated list of feature options that are requested to be turned off. Up to 10 feature options can be specified in the list.
Range:
gttrqd
on (optional)
Enables or turns on the specified feature options. A comma-separated list of feature options that are requested to be turned on. Up to 10 feature options can be specified in the list.
Range:
gttrqd
rqdtblnop (optional)
The action performed if a message arrives at an SCCP card that does not have the necessary RTDB table, and the current message routing is GT.
Range:
udts
generate UDTS for the processed MSU
gtt
fall through to GTT for the processed MSU
disc
discard the processed MSU
snai (optional)
Service nature of address indicator.
Range:
natl
National significant number
intl
International number
rnidn
Routing number prefix and international dialed/directory number
rnndn
Routing number prefix and national dialed/directory number
rnsdn
Routing number prefix and subscriber dialed/directory number
ccrndn
Country code, routing number, and national directory number
sub
Subscriber number
snp (optional)
Service numbering plan.
Range:
e164
e212
e214

Example

ent-srvsel:gtii=4:tt=20:np=e164:nai=intl:serv=eir:ssn=*

ent-srvsel:gtin24=4:tt=4:np=e164:nai=intl:serv=gport:snp=e164:snai=intl:ssn=9

ent-srvsel:gtii=4:tt=4:np=e164:nai=intl:serv=eir:ssn=11

ent-srvsel:gtin=4:tt=9:np=e214:nai=natl:snp=e164:snai=intl:serv=gflex:ssn=250

ent-srvsel:gtii=2:tt=6:snai=intl:snp=e164:serv=smsmr:ssn=10

ent-srvsel:gtii=2:tt=6:snai=intl:snp=e164:serv=gport:ssn=10:on=gttrqd:gttselid=4: dfltact=act2

ent-srvsel:gtii=4:tt=20:np=e164:nai=intl:serv=eir:ssn=*:rqdtblnop=disc

ent-srvsel:gtii=0:tt=0:serv=idpr:ssn=*

Dependencies

The Service Selector table cannot contain more than 1024 entries.

The G-Flex feature must be turned on before the serv=gflex parameter can be specified.

The INP feature must be turned on before the serv=inpmr or serv=inpq parameter can be specified.

The G-Port feature must be turned on before the serv=gport parameter can be specified.

The Equipment Identity Register (EIR) feature must be turned on before the serv=eir parameter can be specified.

The np and npv parameters cannot be specified together in the command.

The nai and naiv parameters cannot be specified together in the command.

The gtia=4 parameter cannot be specified.

The values 1 and 3 are not valid for the gti/gtia/gtii/gtin/gtin24 parameters.

If the gti/gtia/gtii/gtin/gtin24=0 , 2 parameter is specified, then the np(v) and nai(v) parameter combinations cannot be specified.

If the gtii/gtin/gtin24=4 parameter is specified, then an np(v) and nai(v) parameter combination must be specified. The parameters can be specified in the following combinations: np/naiv, npv/nai, np/nai, or npv/naiv.

If the serv parameter has a value of inpmr, gport or eir, then the gtia and gti parameters cannot be specified.

If the serv=inpmr parameter is specified, then the snp=e164 parameter must be specified.

If the serv=inpq parameter is specified, then the gtii parameter cannot be specified.

If the value specified for the snai parameter is rnidn, rnndn, or rnsdn, then the value specified for the serv parameter must be inpmr, gport, or smsmr.

If the value specified for the serv parameter is gflex, gport, inpmr, or smsmr, then the snai and snp parameters must be specified.

If the value specified for the serv parameter is aiq, atinp, eir, idpr, inpq, ttr, or vflex then the snai and snp parameters cannot be specified.

If the snai=ccrndn parameter is specified, then the value specified for the serv parameter must be gport or smsmr.

If the value specified for the serv parameter is gport or smsmr, then the snp=e164 parameter must be specified.

An entry cannot already exist that matches the new gti/gtii/gtin/gtin24, tt, ssn, np(v), and nai(v) combination of parameters.

For the specified gti/gtia/gtii/gtin, tt, np(v), nai(v), and ssn=* parameters, an entry matching a specific ssn cannot already exist.

For the specified gti/gtia/gtii/gtin, tt, np(v), nai(v), and ssn parameters, an entry matching the ssn=* parameter cannot already exist.

If the ansigflex STP option is enabled (see the chg-stpotps command), then an ITU service selector cannot be entered.

The IDP Screening for Prepaid feature must be on before the serv=idps parameter can be specified.

If the serv=idps parameter is specified, then the supported mandatory parameters are tt, serv, ssn, gtin, and gtii. Supported optional parameters are np and nai.

The Prepaid IDP Query Relay feature must be turned on or the IAR Base feature must be enabled before the serv=ttr parameter can be specified.

If a value of idpr or ttr is specified for the serv parameter, then the only valid mandatory service parameters are tt, serv, ssn, gtii, and gtin, and the only valid optional parameters are np and nai.

If the A-Port or IGM feature is enabled, then the serv=gport parameter cannot be specified.

An entry cannot already exist that matches the new gti/gtii/gtin/gtin24, tt, ssn, np(v), and nai(v) combination of parameters.

An entry cannot already exist that matches the new gti/gtii/gtin/gtin24, tt, ssn, np(v), and nai(v) combination of parameters.

An entry cannot already exist that matches the new gti/gtii/gtin/gtin24, tt, ssn, np(v), and nai(v) combination of parameters.

The V-Flex feature must be turned on before the serv=vflex parameter can be specified.

The ATINP feature must be enabled before the serv=atinp parameter can be specified.

The PPSMS or Portability Check for Mobile Originated SMS feature must be turned on, or the MO SMS ASD, MO SMS GRN, MO SMS B-Party Routing, MO SMS IS41-to-GSM Migration, MO-based GSM SMS NP, or MO-based IS41 SMS NP feature must be enabled before the serv=smsmr parameter can be specified.

If a value of aiq, atinp, or eir is specified for the serv parameter, then the gtin24 parameter cannot be specified.

The Prepaid IDP Query Relay feature must be turned on before the serv=idpr parameter can be specified.

The ANSI41 AIQ feature must be enabled before the serv=aiq parameter can be specified.

The A-Port or IGM feature must be turned on, or the A-Port or IGM feature must be enabled and the G-Port feature must be turned on before the serv=mnp parameter can be specified.

If a DSM4G card is active in the system, then the on=gttrqd parameter cannot be specified.

The dfltact, gttselid, and on/off=gttrqd parameters are supported for only the IDPR, TTR, MNP, GPORT, SMSMR, GFLEX, and INPMR services.

If a GTT Action ID is specified as the value for the dfltact parameter, then the Action ID must already exist in the GTT Action table.

The GTT Action table is corrupt or cannot be found.

A valid value must be specified for the dfltact parameter.

The EGTT feature must be turned on before the gttselid or dfltact parameter can be specified.

The same value cannot be specified for the on and off parameters.

The dfltact=none parameter cannot be specified.

The EPAP Data Split feature or the Dual ExAP Config feature must be on before the rqdtblnop parameter can be specified.

If a value of inpq, vflex, atinp, or eir is specified for the serv parameter, then the rqdtblnop=gtt parameter cannot be specified.

If a value of aiq or idps is specified for the serv parameter, then the rqdtblnop parameter cannot be specified.

The requested service selector entry must exist in the database.

The GSM DBMM table must be accessible.

Only for IDP Relay feature, gtii/gtin/gtin24=0 can be specified.

If the serv=idpr parameter is specified and the gti/gtia/gtii/gtin/gtin24=0, tt=0 parameter is entered, then the gti/gtia/gtii/gtin/gtin24=2, tt=0 parameter combinations cannot be entered. The parameters can be specified in the following combinations: gtii=0 tt=0, or gtii=2 tt=0.

Notes

on/off options

  • gttrqd —GTT required. Specifies whether GTT is required after service execution is complete and the message is relayed by the service. This option is supported for the IDPR, MNP, TTR, GPORT, SMSMR, GFLEX, and INPMR services.

Output

ent-srvsel:gtia=4:tt=10:ssn=25:snai=natl:serv=aiq

    tekelecstp 09-12-03 16:40:40 EST  EAGLE 42.0.0
    Service Selector table is (114 of 1024) 11% full
    ENT-SRVSEL: MASP A - COMPLTD 
;
ent-srvsel:gtia=2:tt=20:ssn=105:snai=natl:serv=inp

    tekelecstp 13-09-26 11:51:11 EST  EAGLE 46.0.0
    Service Selector table is (11 of 1024) 1% full
    ENT-SRVSEL: MASP A - COMPLTD 
;