oracle home
Configuring an Oracle
®
Solaris 11.2 System as a Router or a Load Balancer
Exit Print View
Search Term
Search Scope:
This Document
Entire Library
» ...
Documentation Home
»
Oracle Solaris 11.2 Information Library
»
Configuring an Oracle
®
Solaris ...
»
Configuring and Administering Virtual Router ...
»
Installing VRRP
Updated: September 2014
Configuring an Oracle
®
Solaris 11.2 System as a Router or a Load Balancer
Document Information
Using This Documentation
Product Documentation Library
Access to Oracle Support
Feedback
Chapter 1 Introduction to Routers and Load Balancers
Router Overview
Routing Protocols
Routing Information Protocol
ICMP Router Discovery Protocol
Quagga Routing Protocol Suite
Virtual Router Redundancy Protocol
VRRP Router Overview
Integrated Load Balancer Overview
Features of ILB
Why Use VRRP Routers and Load Balancers?
Chapter 2 Configuring a System as a Router
Configuring an IPv4 Router
How to Configure an IPv4 Router
Configuring an IPv6 Router
in.ripngd Daemon, for IPv6 Routing
Router Advertisement, Prefixes, and Messages
How to Configure an IPv6-Enabled Router
Chapter 3 Using Virtual Router Redundancy Protocol
About VRRP
How VRRP Works
About the Layer 3 VRRP Feature
Comparing Layer 2 and Layer 3 VRRP
Limitations of Layer 2 and Layer 3 VRRP
Chapter 4 Configuring and Administering Virtual Router Redundancy Protocol
Planning a VRRP Configuration
Installing VRRP
How to Install VRRP
Configuring VRRP
Creating a VRRP VNIC for Layer 2 VRRP
Creating a VRRP Router
Configuring the Virtual IP Address for Layer 2 and Layer 3 VRRP Routers
Enabling and Disabling a VRRP Router
Modifying a VRRP Router
Displaying Layer 2 and Layer 3 VRRP Router Configurations
Displaying IP Addresses That Are Associated With VRRP Routers
Deleting a VRRP Router
Controlling Gratuitous ARP and NDP Messages
Use Case: Configuring a Layer 2 VRRP Router
Chapter 5 Overview of an Integrated Load Balancer
ILB Components
ILB Operation Modes
Direct Server Return Mode
Network Address Translator Mode
Half-NAT Load-Balancing Mode
Full-NAT Load-Balancing Mode
How ILB Works
Chapter 6 Configuring and Managing the Integrated Load Balancer
Installing ILB
Configuring ILB by Using the Command-Line Interface
Enabling or Disabling ILB
How to Enable ILB
How to Disable ILB
Managing an ILB
Defining Server Groups and Back-End Servers in ILB
Creating an ILB Server Group
Adding Back-End Servers to an ILB Sever Group
Enabling or Disabling a Back-End Server in an ILB Server Group
Deleting a Back-End Server From an ILB Server Group
Deleting ILB Server Groups
Monitoring Health Checks in ILB
Creating a Health Check
Listing Health Checks
Displaying Health Check Results
Deleting a Health Check
Configuring ILB Rules
ILB Algorithms
Creating an ILB Rule
Listing ILB Rules
Deleting an ILB Rule
Use Case: Configuring an ILB
Displaying ILB Statistics
Displaying Statistical Information
Displaying the NAT Connection Table
Displaying the Session Persistence Mapping Table
Importing and Exporting Configurations
Chapter 7 Configuring ILB for High Availability
Configuring ILB for High Availability By Using the DSR Topology
How to Configure ILB for High Availability by Using the DSR Topology
Configuring ILB for High Availability By Using the Half-NAT Topology
How to Configure ILB for High-Availability by Using the Half-NAT Topology
Index
Index A
Index B
Index C
Index D
Index E
Index G
Index H
Index I
Index L
Index M
Index N
Index O
Index P
Index Q
Index R
Index S
Index T
Index V
Language:
English
Installing VRRP
You must install VRRP to use VRRP on your system.
Previous
Next