C H A P T E R 2 |
Installing and Configuring the Server Module |
This chapter provides instructions for installing and configuring the server module. It contains the following sections:
To Insert the Server Module |
1. Locate the desired slot in the chassis.
Pull the lever out and eject the filler panel.
Do not discard the filler panel.
Caution - Do not operate the system with empty slots. Always insert a filler panel into an empty slot to reduce the possibility of module shutdown. |
3. Position the server module vertically so that the ejectors are on the right.
The following illustrations show the server module being inserted into the Sun Blade 6000 modular system; your chassis might differ. See box 1 in FIGURE 2-1 [1].
FIGURE 2-1 Inserting the Server Module Into the Chassis
4. Push the server module into the slot until the server module stops.
See FIGURE 2-1 [2].
5. Rotate the ejectors down until they snap into place.
The server module is now flush with the chassis, and the ejectors are locked. See boxes 3 and 4 in FIGURE 2-1 [3,4].
If the chassis is powered on, the server module comes up to standby power. The green OK LED on the front panel flashes. With ILOM 2.0, the blue OK to Remove LED remains on. See FIGURE 1-1.
When the server module is inserted in the chassis, the LEDs blink in a specific sequence.
When you apply power to the server module, the blue, amber, and green status LEDs blink three times, at one second invervals (.5 sec On, .5 sec Off).
The green LED blinks at one-second intervals until the SP starts IPMI services.
When the IPMI services are running:
When you apply power to the server module, the blue, amber, green status, and white Locate LEDs blink three times, at one second invervals (.5 sec On, .5 sec Off).
After the three blinks, the green LED goes to fast blink while the ILOM performs power calculations (.125 sec On, .125 sec Off).
When the system is ready to turn on, the green LED stays ON for 3 seconds. You can now press the Power button to power on the host.
Until you press the power button, the green LED switches to standby blink
(.1 sec On, 2.9 sec Off).
After you press the power button, the green LED slow blinks while the host powers up and BIOS runs (.5 sec On, .5 sec Off).
When the OS starts to boot, the green LED stays On.
If the ILOM has calculated that the server module is exceeding its power budget, the green LED stays Off instead.
The server module includes a service processor (SP) integrated into the motherboard.
This section provides instructions for:
The SP’s built-in system management software enables you to monitor and manage the components installed in your chassis and server modules. Using the SP, you can configure network information, view and edit hardware configurations, monitor vital system information, and manage user accounts.
The chassis has its own service processor, called a Chassis Monitoring Module Integrated Lights Out Manager (CMM ILOM). In addition to providing chassis management functions, it provides an Ethernet connection to the server module's SP. This allows you to view and configure the server module's network information using the CMM ILOM.
The following sections assume that:
If these conditions are not present, see the documentation for your service processor. as listed in Service Processor Versions.
Your server module might be equipped with one of several versions of the SP:
For additional documentation, see the ILOM 3.0 documentation collection.
For additional documentation, see the ILOM 2.0 documentation collection.
For additional documentation, see the ELOM documentation collection.
While there are fundamental differences between ILOM 2.0 and ILOM 3.0, they do not affect the procedures in this section; all of these procedures can be used for both. Any minor differences are noted where they occur.
The ILOM provides both a command line interface (CLI), and a web interface. This section provides procedures for using both of these interfaces.
You can migrate your SP from ELOM to ILOM 2.0, and you can upgrade ILOM 2.0 to ILOM 3.0.
Caution - When you migrate from ELOM to ILOM 2.0, use SW2.0.3 or newer. Do not migrate from ELOM to a version of ILOM from an earlier software release. |
Use the following procedure to display the ILOM’s network configuration, including the IP address of the ILOM SP, using the CMM ILOM.
This procedure also verifies that the ILOM is working correctly and that you can access it through the CMM ILOM.
Note - This procedure can be used for ELOM as well as ILOM 2.0 and ILOM 3.0. |
1. Log in to the CMM ILOM CLI.
where n is the server module number or chassis slot ID.
The CMM ILOM displays information about the server module, including its IP address and MAC address. For example:
This section describes how to connect to the ILOM’s CLI and web interface.
Note - To improve response times, disable the browser proxy server (if used). |
If you do not know the ILOM’s IP address, find it as described in Displaying the Service Processor’s IP Address .
Follow these steps to log in to the ILOM web interface:
1. To log in to the web interface, type the ILOM’s IP address into your web browser.
The web interface Login page appears.
Note - FIGURE 2-2 and FIGURE 2-3 show the Login page and Version page for ILOM 3.0. For ILOM 2.0, the procedures are the same but the pages might look slightly different. |
FIGURE 2-2 Login Page for ILOM 3.0
2. Type your user name and password.
The default user is root, and the default password is changeme, all in lowercase characters.
Note - After you log in to the SP using the default user name and password, you should change the the root account password (changeme). See the corresponding SP documentation collection for details. |
The web interface Versions page appears.
FIGURE 2-3 Versions Page for ILOM 3.0
You can access the ILOM CLI remotely through a Secure Shell (SSH) or serial connection. Secure Shell connections are enabled by default.
If you do not know the ILOM’s IP address, find it as described in Displaying the Service Processor’s IP Address.
The following procedure shows an example using an SSH client on a UNIX system. Use an appropriate SSH client for your operating system. The default user name is root and default password is changeme.
Follow these steps to log in to ILOM using the default enabled SSH connection:
1. To log on to the ILOM, type:
where ipaddress is the ILOM’s IP address.
2. Type the password when prompted. The default is changeme:
The CMM ILOM allows you to change the server module network information, including the IP address, and DHCP settings.
See the ILOM documentation for your chassis for details.
2. Navigate to /CH/BLn/SP/network.
Where n is 0 through 9 for server modules 0 through 9 respectively.
Note - You can also change these settings using the ILOM 2.0 or ILOM 3.0 instead of the CMM ILOM. Navigate to /SP/network instead of /CH/BLn/SP/network. Once there, the commands are identical. |
3. Type the following commands:
where xxx.xxx.xx.xx, yyy.yyy.yyy.y and zzz.zzz.zz.zzz are the IP address, netmask, and gateway for your SP and network configuration.
set pendingipdiscovery=dhcp set commitpending=true
Note - Typing set commitpending=true commits your changes. |
This section describes how to connect to the system console.
Choose one of the following ways to access the system console:
After you can view the system console, refer to the documentation for your operating system. See the Sun Blade X6450 Server Module Operating System Installation Guide, or the Sun Blade X6450 Server Module Windows Operating System Installation Guide.
1. Connect a keyboard, monitor, and mouse to the dongle cable on the server module front panel. See Dongle Cable Connections.
2. To power the server on or off, use a stylus as described in Routine Power On and Power Off.
1. Connect and log in to the ILOM as described in Connecting to the ILOM.
2. To power on the system, type the command:
Note - You can also power the system on or off using a stylus, as described in Routine Power On and Power Off. |
3. To start the system console, type:
4. To exit the system console, press Esc-Shift-9.
Note - This procedure shows screens from ILOM 2.0. In ILOM 3.0, the procedures work the same, but the screens might have slight differences. |
1. Log on to the web interface as described in To Connect to the ILOM Web Interface.
FIGURE 2-4 ILOM 2.0 Versions Screen
2. Click on the Remote Control tab.
The Remote Control screen appears.
FIGURE 2-5 ILOM 2.0 Remote Control Screen
3. Click the Launch Redirection tab.
After some messages, the console appears.
FIGURE 2-6 Redirection Screen Displaying BIOS Session
The dongle cable, which is shipped with your chassis, allows you to connect directly to the front of your server module, as shown in FIGURE 2-7.
Note - The dongle cable has either three or four connectors. FIGURE 2-7 shows a dongle with four connectors. The three-connector dongle does not have the DB9 serial console connector (1). |
To connect to the system console:
The dongle cable is designed for occasional service use. For routine operation, use the ILOM.
FIGURE 2-7 Dongle Cable Connections
Caution - To avoid physical damage to the dongle cable and the connector, disconnect the dongle when it is not being used. |
Copyright © 2009 Sun Microsystems, Inc. All rights reserved.