This document contains basic information on setting up the Sun Fire X4540 server. Detailed installation information can be found in the orderable option, Sun Fire X4500/X4540 Installation Guide, (820-4855). Additional Sun Fire X4540 server documentation is available at:
http://docs.sun.com/app/docs/prod/sf.x4540
Before performing an installation of the Sun Fire X4540 server, refer to the Safety and Compliance Guide and the Important Safety Information for Sun Hardware Systems, (included in the ship kit).
After unpacking and rack mounting the system, attach cables to the available input-output (I/O) ports on the Sun Fire X4540 server. Attach cables to the back panel connectors of your server as required. See FIGURE 1.
FIGURE 1 Sun Fire X4540 Server Back Panel
Note -
The PSU cover plate will be updated. |
The server has two levels of power: standby power and main power. For initial configuration of the service processor (SP), you need to apply standby power. The procedures for powering on to main power mode and for shutting down from main power mode are also included in this section.
Use this procedure to apply standby power to SP before initial configuration.
1. Connect a grounded AC power cord into the two AC power connectors on the back panel of the server and into grounded AC (200 VAC to 240 VAC) power outlets.
Note - This system is shipped for operation at 220 VAC. 110 VAC operation with a third PSU will be available as an orderable option. |
Continue with initial software setup tasks, as explained in Connecting to the ILOM Service Processor
Powering On Main Power Mode |
1. Verify that power cords have been connected and that standby power is on. In standby power mode, the Power/OK LED on the front panel blinks.
Note - See the service label on the hard disk drive access cover for an explanation of the LEDs on the hard disk drives, fans, power supply, and system controller. |
2. Use a stylus to press and release the recessed Power button on the server front panel.
Note - When main power is applied to the server, the Power/OK LED next to the Power button lights and remains lit. The power-on self-test (POST) can take up to a minute to complete. |
Powering Off the Server |
To power off the server from main power mode, use one of the following two methods:
Caution - To power off the server completely, you must disconnect the AC power cords from the power supplies at the rear of the server. |
Integrated Lights Out Manager (ILOM) is system management firmware that is preinstalled on your server. ILOM enables you to manage and monitor components installed in your server system.
Use one of the following methods to connect to the ILOM SP to perform initial setup and configuration.
Detailed installation information can be found in the orderable option, Sun Fire X4500/X4540 Installation Guide.
See the Sun Fire X4540 Server documentation at: http://docs.sun.com/app/docs/prod/sf.x4540 |
||||
---|---|---|---|---|
Addendum to the Sun Integrated Lights Out Manager 2.0 User’s Guide |
Information on ILOM features incorporated since the initial release of ILOM 2.0 firmware |
|||
Instructions for using the applications and utilities common to many x64 servers. |
||||
Install or replace hardware components. Customize BIOS settings. Remove and replace hardware components. |
||||
Troubleshoot and isolate server problems, with available diagnostic tools and logs. |
||||
Sun Installation Assistant for Windows and Linux User’s Guide |
Provides detailed information about installing supported operating systems on Sun Fire rack mounted servers. |
|||
Install, determine network settings, configure the preinstalled Solaris operating system. |
||||
Sun Fire X4500/X4540 Server Operating System Installation Guide |
Install Solaris operating system and supported Linux operating systems |
|||
Sun Fire X4500/X4540 Server Windows Operating System Installation Guide |
||||
How to install a Sun system into a rack with the X-4500 J slide rail system. |
||||
Contacting Sun Technical Support for questions about this product |
|
Select a language from the drop-down list and navigate to the Sun Fire X4540 Server document collection. |
|
http://www.sun.com/hwdocs/feedback and click on the Feedback Link to open the form. Please include the title and part number of your document. |
|