|
Error Message |
Probable Cause(s) |
Suggested Action (if applicable) |
---|---|---|---|
6000 |
Signal To Noise ratio too low (name) on name, SNR =number db, Min SNR =number db (text) |
Loopback cable is missing or faulty. Audio hardware (usually consistent failures). System software problem (usually intermittent failures). |
|
6001 |
Channel Separation too low (name), SEP =number db, Min SEP =number db (text) |
Loopback cable is faulty. Audio hardware is faulty (usually consistent failures). System software problem (usually intermittent failures). |
|
6002 |
Loop gain is out of range (name), name GAIN =number db, Min =number Max =number db (text) |
Loopback cable is missing or faulty. Audio hardware is faulty (usually consistent failures). System software problem (usually intermittent failures). |
|
8000 |
Must be super user (root) to execute |
The user does not have root privileges. |
|
8012 |
Invalid audio device (device_name) for Crystal test |
The crystal test is not supported on the system audio device. |
|
8013 |
Invalid audio device (device_name) for Controls test |
The system audio device does not support a speakerbox. |
|
8014 |
Invalid audio device (device_name) for Loopback Quality test |
No loopback tests are supported on the system audio device. |
|
8015 |
Invalid audio device (device_name) for Loopback Quality test (T=number) |
The specified loopback test is not supported on the system audio device. The specified loopback type is not supported on this audio device. |
|
|
|
||
8020 |
Incomplete button press sequence |
The required button presses were not detected in the time allowed. |
|
8023 |
Underrun/Overrun error failure |
The audio driver detected underrun or overrun errors while transferring data to the audio device. These errors usually happen when the loopback test is run while during heavy system activity. |
|
8027 |
name: `name(name=number, name=number, name=number)' system call timeout. No response after number seconds. Device = device_name |
The system call is hanging. |
|
Audio hardware (usually consistent failures).
|
|
||
System software problem (usually intermittent failures).
|
|
||
8028 |
Audio crystal test did not complete in the expected time, rate = number Hz, time = number usecs, min = number, max = number |
Excessive loading on the system. |
Disable all other tests and try again. |
8029 |
Speaker is an invalid output port for device |
The system does not have an on-board speaker. |
|
8032 |
Failed ioctl name (error_message) |
The ioctl( ) system call failed. |
See the appended error message. |
8033 |
Failed mmap (error_message) |
The mmap( ) system call failed. |
See the appended error message. |
8034 |
Failed fstat (error_message) |
The fstat( ) system call failed. |
See the appended error message. |
8035 |
Failed ftruncate (error_message) |
The ftruncate( ) system call failed. |
See the appended error message. |
8036 |
Write to audio device returned error condition (error_message) |
The write( ) system call failed. |
See the appended error message. |
8037 |
Read from audio device returned error condition (error_message) |
The read( ) system call failed. |
See the appended error message. |
8038 |
Failed to allocate number bytes of memory (error_message) |
The memory allocation system call failed, most likely due to a lack of system memory resource. |
See the appended error message. |
8051 |
Unknown audio device (name=device_name, config=name) |
|
|
8052 |
Unable to get platform name |
|
|
8053 |
Unknown architecture/audio = name / device_name |
|
|
8055 |
Could not open device_name: error_message |
The open( ) system call failed Examine system message files (/var/adm/messages) for other information. Device does not respond. No mmcodec device found. Unable to communicate with speakerbox. |
|
8075 |
Invalid audio file format |
Specified audio file is not in expected format. |
|
8077 |
Invalid audio encoding |
An unknown audio encoding type was specified. |
|
8090 |
Only one name loopback can be selected at a time |
The user specified more than one loopback test on the same port. |
|
8091 |
Cannot enable loopback testing without selecting a loopback type |
The user enabled loopback testing but did not specify a loopback type. |
|