Error Message |
Probable Cause(s) |
Recommended Action |
|
---|---|---|---|
6000
|
Re-reading and recomparing block number on name |
Media error. |
If the problem persists, call your authorized Sun service provider. |
Faulty cable, disk, or controller. |
|||
6002 |
Error on recomparing block number on name |
Media error. |
If the problem persists, call your authorized Sun service provider. |
Faulty cable, disk, or controller. |
|||
6004 |
name failed on name, blk number: error_message |
Faulty cable, disk, or controller. |
If the problem persists, call your authorized Sun service provider. |
6006 |
Compare error on name, block number, offset number |
Faulty cable, disk, or controller. |
If the problem persists, call your authorized Sun service provider. |
6008 |
Compare error: Block number on name was written with a repeating hex pattern of number |
Media error. |
If the problem persists, call your authorized Sun service provider. |
Faulty cable, disk, or controller. |
|||
6010 |
TIME OUT! |
System too busy. |
Reduce the system load. |
Faulty cable, disk, or controller. |
If the problem persists, call your authorized Sun service provider. |
||
6012 |
Couldn't close name |
System error. |
|
6014 |
name read failed on disk, in-between blocks number and number: name |
Media error. |
If the problem persists, call your authorized Sun service provider. |
Faulty cable, disk, or controller. |
|||
6016 |
name read failed due to unexpected end of media |
|
|
6018 |
name write failed on disk, in-between blocks number and number: name |
Media error. |
If the problem persists, call your authorized Sun service provider. |
Faulty disk or controller. |
|||
6020 |
name write failed due to unexpected end of media: |
|
|
6022 |
name compare failed on name, block number, offset number |
Media error. |
If the problem persists, call your authorized Sun service provider. |
Faulty disk or controller. |
|||
6024 |
Couldn't close name |
Faulty disk or controller. |
If the problem persists, call your authorized Sun service provider.
|
System error. |
|||
6026 |
failed automount name onto name:error_message |
Un-supported file system. |
Disable the file system subtest. |
System error. |
Disable the file system subtest. |
||
|
If the problem persists, call your authorized Sun service provider. |
||
6028 |
error_message |
|
|
8000 |
File system subtest only allow to run on off-line mode |
Parameter error. |
Re-enter the command line correctly. |
8002 |
malloc() failed |
System load too heavy. |
|
System error. |
|
||
8006 |
File operation error: Couldn't name file name on name: error_message |
Lack of system resource. |
Reduce the system load. |
Permission error. |
Check directory or file permission. |
||
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8008 |
Not enough free blocks on name (partition number) |
|
Try another partition or delete files. |
8010 |
No writable partition on name |
|
Try another partition. |
8012 |
No file system on device: name |
|
Use newfs to create the file system. |
Disable the file system subtest. |
|||
8014 |
Couldn't run fstest on any partition of device: name(except 2) |
File system not supported. |
Disable the file system subtest. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8016 |
Cannot open device: name |
Parameter error. |
Enter the correct name of disk as dev=c0t3d0. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8018 |
Couldn't mount /dev/dsk/name |
Parameter error. |
Enter the correct name of disk as dev=c0t3d0. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8020 |
Couldn't remove temporary dir name: error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8022 |
fail get semaphore: error_message |
Lack of system resource. |
Reduce the system load. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8024 |
failed lock mtab semaphore: "semap" system call failure, errmsg error_message |
disktest instances exceed system semaphore operation limitation (default system limit for seminfo_semmnu=30)system software error. |
Add the line "set semsys: seminfo_semmnu=0x100" to your /etc/system file and reboot the machine. If the problem persists, call your authorized Sun service provider. |
8026 |
fail unlock mtab semaphore: error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8028 |
failed get_volmgr_name() |
|
|
8030 |
Couldn't open name: error_message |
Cable loose or disconnected. |
Check the cable. |
Device off line or missing. |
Check the device on line. |
||
Device not configured. |
Configure the device. |
||
8032 |
Get file state name failed: error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8034 |
Couldn't open name |
Permission error. |
Check the permissions. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8036 |
failed putmntent(): error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8038 |
fail rename file |
Permission error. |
Check permission. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8040 |
Couldn't get mount table entry for name |
|
|
8042 |
Invalid device name in name |
Parameter error. |
Enter the correct name of disk as dev=c0t3d0. |
8044 |
Message table overflow on device name |
Parameter error. |
Enter the correct name of disk as dev=c0t3d0. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
Program error. |
|||
8046 |
Invalid controller id name for name |
Parameter error. |
Re-enter the command line correctly. |
8048 |
name, disk DKIOCINFO ioctl: name |
Controller is not supported. |
Disable the file system subtest. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8050 |
failed getting shared memory for monitor number: error_message: |
Lack of system resource. |
Reduce the system load. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8052 |
failed attaching monitor shared memory:error_message |
Lack of system resource. |
Reduce the system load. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8053 |
failed create monitor shared memory number: |
Lack of system resource. |
Reduce the system load. |
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8054 |
Shm remove error: error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8056 |
New error messages in system log. Extracted below:error_message |
Faulty cable/disk/controller. |
See /var/adm/messages for more information. |
If the problem persists, consult your authorized Sun service provider. |
|||
8060 |
fails to open any partition of name |
File system not mounted. |
Mount the file system then run the test. |
Disable the file system subtest. |
|||
If the problem persists, call your authorized Sun service provider. |
|||
8060 |
failed getting semaphore: error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8062 |
failed getting shared memory: error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8064 |
failed attaching shared memory:error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8068 |
failed unlocking semaphore: error_message |
System error. |
If the problem persists, call your authorized Sun service provider. |
8070 |
fail open floppy disk |
No floppy disk in drive. |
Check the floppy disk. |
8072 |
failed FDIOGCHAR on floppy ioctl |
System error. |
If the problem persists, call your authorized Sun service provider. |
8074 |
ioctl DKIOCGGEOM failed |
File system not supported. |
If the problem persists, call your authorized Sun service provider. |
System error. |
|||
8074 |
ioctl DKIOCGAPART failed |
System error. |
If the problem persists, call your authorized Sun service provider. |
8076 |
fail initialize shared memory |
System error. |
If the problem persists, call your authorized Sun service provider. |
8078 |
Illegal parameters on Online Mode |
Parameter error. |
Enter the correct option. |
8080 |
Illegal parameters on Conn. Mode |
Parameter error. |
Enter the correct option. |
8082 |
failed get_volmgr_name() |
No floppy disk in drive. |
Check the floppy disk. |
8084 |
Mounted file system on device! |
Not enough disk space. |
Reduce the system load. |
Permission error. |
Check directory or file permissions. |
||
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8086 |
Invalid controller id number from name |
Parameter error. |
Enter the correct name of disk as dev=c0t3d0. |
8088 |
Couldn't get file system information on name errno=number |
System error. |
If the problem persists, call your authorized Sun service provider. |
8090 |
ioctl() failed on name: name |
System error. |
If the problem persists, call your authorized Sun service provider. |
8092 |
Fail to get disk information |
No supported disk. |
No UNIX message monitor feature in this disk(2). |
System load is too heavy. |
Reduce the system load |
||
8094 |
Failed to create a message base for controller number |
No disk under this controller. |
Connect the disk driver then run the test again. |
8096 |
fail to make directory name |
Lack of system resource. |
Reduce the system load. |
Permission error. |
Check directory or file permissions. |
||
System error. |
If the problem persists, call your authorized Sun service provider. |
||
8098 |
Failed to mount partition |
Does this disk only have partition 2. |
Partition 2 must be manually mounted. |
8010 |
r/w is on /dev/rname |
System error. |
If the problem persists, call your authorized Sun service provider. |
8102 |
write/read count error |
Out of disk space. |
Try another partition or delete some files. |
8104 |
failed to create buffer |
Not enough memory. |
Reduce the system load. If the problem persists, call your authorized Sun service provider. |
8106 |
failed aioread() : offset error number error string |
Faulty cable, disk, or controller. |
If the problem persists, call your authorized Sun service provider. |
8108 |
failed aiowrite() : offset error number error string |
Faulty cable, disk, or controller. |
If the problem persists, call your authorized Sun service provider. |
8110 |
failed io operation() : number text |
Faulty cable, disk, or controller. |
If the problem persists, call your authorized Sun service provider. |