JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Oracle VM Server for SPARC 2.1 Administration Guide     Oracle VM Server for SPARC
search filter icon
search icon

Document Information


Part I Oracle VM Server for SPARC 2.1 Software

1.  Overview of the Oracle VM Server for SPARC Software

2.  Installing and Enabling Software

3.  Security

4.  Setting Up Services and the Control Domain

5.  Setting Up Guest Domains

6.  Setting Up I/O Domains

7.  Using Virtual Disks

8.  Using Virtual Networks

Introduction to a Virtual Network

Virtual Switch

Virtual Network Device

Inter-Vnet LDC Channels

Virtual Device Identifier and Network Interface Name

Find Oracle Solaris OS Network Interface Name

Assigning MAC Addresses Automatically or Manually

Range of MAC Addresses Assigned to Logical Domains

Automatic Assignment Algorithm

Duplicate MAC Address Detection

Freed MAC Addresses

Using Network Adapters With Logical Domains

Determine If a Network Adapter Is GLDv3-Compliant

Configuring Virtual Switch and Service Domain for NAT and Routing

Set Up the Virtual Switch to Provide External Connectivity to Domains

Configuring IPMP in a Logical Domains Environment

Configuring Virtual Network Devices Into an IPMP Group in a Domain

Configuring and Using IPMP in the Service Domain

Using Link-Based IPMP in Logical Domains Virtual Networking

Configure Physical Link Status Updates

Configuring and Using IPMP in Releases Prior to Logical Domains 1.3

Configuring IPMP in the Guest Domain

Configuring IPMP in the Service Domain

Using VLAN Tagging



Assign VLANs to a Virtual Switch and Virtual Network Device

Install a Guest Domain When the Install Server Is in a VLAN

Using NIU Hybrid I/O

Configure a Virtual Switch With an NIU Network Device

Enable Hybrid Mode

Disable Hybrid Mode

Using Link Aggregation With a Virtual Switch

Configuring Jumbo Frames

Configure Virtual Network and Virtual Switch Devices to Use Jumbo Frames

Compatibility With Older (Jumbo-Unaware) Versions of the vnet and vsw Drivers

9.  Migrating Domains

10.  Managing Resources

11.  Managing Configurations

12.  Performing Other Administration Tasks

Part II Optional Oracle VM Server for SPARC Software

13.  Oracle VM Server for SPARC Physical-to-Virtual Conversion Tool

14.  Oracle VM Server for SPARC Configuration Assistant

15.  Using the Oracle VM Server for SPARC Management Information Base Software

16.  Logical Domains Manager Discovery

17.  Using the XML Interface With the Logical Domains Manager



Using Link Aggregation With a Virtual Switch

As of the release of the Oracle Solaris 10 10/08 OS and the Logical Domains 1.1 software, the virtual switch can be configured to use a link aggregation. A link aggregation is used as the virtual switch's network device to connect to the physical network. This configuration enables the virtual switch to leverage the features provided by the IEEE 802.3ad Link Aggregation Standard. Such features include increased bandwidth, load balancing, and failover. For information about how to configure link aggregation, see the System Administration Guide: IP Services.

After you create a link aggregation, you can assign it to the virtual switch. Making this assignment is similar to assigning a physical network device to a virtual switch. Use the ldm add-vswitch or ldm set-vswitch command to set the net-dev property.

When the link aggregation is assigned to the virtual switch, traffic to and from the physical network flows through the aggregation. Any necessary load balancing or failover is handled transparently by the underlying aggregation framework. Link aggregation is completely transparent to the virtual network (vnet) devices that are on the guest domains and that are bound to a virtual switch that uses an aggregation.

Note - You cannot group the virtual network devices (vnet and vsw) into a link aggregation.

You can create and use the virtual switch that is configured to use a link aggregation in the service domain. See Configure the Virtual Switch as the Primary Interface.

The following figure illustrates a virtual switch configured to use an aggregation, aggr1, over physical interfaces nxge0 and nxge1.

Figure 8-10 Configuring a Virtual Switch to Use a Link Aggregation

image:Diagram shows how to set up a virtual switch to use a link aggregation as described in the text.