JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Oracle Solaris Administration: IP Services     Oracle Solaris 11 Information Library
search filter icon
search icon

Document Information


Part I TCP/IP Administration

1.  Planning the Network Deployment

2.  Considerations When Using IPv6 Addresses

3.  Configuring an IPv4 Network

4.  Enabling IPv6 on the Network

5.  Administering a TCP/IP Network

6.  Configuring IP Tunnels

7.  Troubleshooting Network Problems

General Network Troubleshooting Tips

Running Basic Diagnostic Checks

How to Perform Basic Network Software Checking

Common Problems When Deploying IPv6

IPv4 Router Cannot Be Upgraded to IPv6

Problems After Upgrading Services to IPv6

Current ISP Does Not Support IPv6

Security Issues When Tunneling to a 6to4 Relay Router

8.  IPv4 Reference

9.  IPv6 Reference


10.  About DHCP (Overview)

11.  Administering the ISC DHCP Service

12.  Configuring and Administering the DHCP Client

13.  DHCP Commands and Files (Reference)

Part III IP Security

14.  IP Security Architecture (Overview)

15.  Configuring IPsec (Tasks)

16.  IP Security Architecture (Reference)

17.  Internet Key Exchange (Overview)

18.  Configuring IKE (Tasks)

19.  Internet Key Exchange (Reference)

20.  IP Filter in Oracle Solaris (Overview)

21.  IP Filter (Tasks)

Part IV Networking Performance

22.  Integrated Load Balancer Overview

23.  Configuration of Integrated Load Balancer (Tasks)

24.  Virtual Router Redundancy Protocol (Overview)

25.  VRRP Configuration (Tasks)

26.  Implementing Congestion Control

Part V IP Quality of Service (IPQoS)

27.  Introducing IPQoS (Overview)

28.  Planning for an IPQoS-Enabled Network (Tasks)

29.  Creating the IPQoS Configuration File (Tasks)

30.  Starting and Maintaining IPQoS (Tasks)

31.  Using Flow Accounting and Statistics Gathering (Tasks)

32.  IPQoS in Detail (Reference)



General Network Troubleshooting Tips

One of the first signs of trouble on a network is a loss of communications by one or more hosts. If a host does not to come up at all the first time that the host is added to the network, the problem might be in one of the configuration files. The problem might also be a faulty network interface card. If a single host suddenly develops a problem, the network interface might be the cause. If the hosts on a network can communicate with each other but not with other networks, the problem could lie with the router. Or, the problem could be in another network.

You can use the ipadm command to obtain information on network interfaces. Use the netstat command to display routing tables and protocol statistics. Third-party network diagnostic programs provide a number of troubleshooting tools. Refer to third-party documentation for information.

Less obvious are the causes of problems that degrade performance on the network. For example, you can use tools such as ping to quantify problems such as the loss of packets by a host.

Running Basic Diagnostic Checks

If the network has problems, you can run a series of software checks to diagnose and fix basic, software-related problems.

How to Perform Basic Network Software Checking

  1. Use the netstat command to display network information.

    For syntax and information about the netstat command, refer to Monitoring Network Status With the netstat Command and the netstat(1M) man page.

  2. Check the hosts database to ensure that the entries are correct and current.

    For information about the /etc/inet/hosts database, refer to Network Configuration Files and the hosts(4) man page.

  3. If you are running the Reverse Address Resolution Protocol (RARP), check the Ethernet addresses in the ethers database to ensure that the entries are correct and current.
  4. Try to connect to the local host by using the telnet command.

    For syntax and information about telnet, refer to the telnet(1) man page.

  5. Ensure that the network daemon inetd is running.

    # ps -ef | grep inetd

    The following output verifies that the inetd daemon is running:

    root 57 1 0 Apr 04 ? 3:19 /usr/sbin/inetd -s
  6. If IPv6 is enabled on your network, verify that the IPv6 daemon in.ndpd is running:
    # ps -ef | grep in.ndpd

    The following output verifies that the in.ndpd daemon is running:

    root 123  1 0  Oct 27 ?  0:03 /usr/lib/inet/in.ndpd