JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Oracle Solaris Administration: Network Interfaces and Network Virtualization     Oracle Solaris 11 Information Library
search filter icon
search icon

Document Information


1.  Overview of the Networking Stack

Network Configuration in This Oracle Solaris Release

The Network Stack in Oracle Solaris

Network Devices and Datalink Names

Administration of Other Link Types

Part I Network Auto-Magic

2.  Introduction to NWAM

3.  NWAM Configuration and Administration (Overview)

4.  NWAM Profile Configuration (Tasks)

5.  NWAM Profile Administration (Tasks)

6.  About the NWAM Graphical User Interface

Part II Datalink and Interface Configuration

7.  Using Datalink and Interface Configuration Commands on Profiles

8.  Datalink Configuration and Administration

9.  Configuring an IP Interface

10.  Configuring Wireless Interface Communications on Oracle Solaris

11.  Administering Bridges

12.  Administering Link Aggregations

13.  Administering VLANs

14.  Introducing IPMP

What's New With IPMP

Deploying IPMP

Why You Should Use IPMP

When You Must Use IPMP

Comparing IPMP and Link Aggregation

Using Flexible Link Names on IPMP Configuration

How IPMP Works

IPMP Components in Oracle Solaris

Types of IPMP Interface Configurations

IPMP Addressing

IPv4 Test Addresses

IPv6 Test Addresses

Failure and Repair Detection in IPMP

Types of Failure Detection in IPMP

Probe-Based Failure Detection

Link-Based Failure Detection

Failure Detection and the Anonymous Group Feature

Detecting Physical Interface Repairs

The FAILBACK=no Mode

IPMP and Dynamic Reconfiguration

Attaching New NICs

Detaching NICs

Replacing NICs

IPMP Terminology and Concepts

15.  Administering IPMP

16.  Exchanging Network Connectivity Information With LLDP

Part III Network Virtualization and Resource Management

17.  Introducing Network Virtualization and Resource Control (Overview)

18.  Planning for Network Virtualization and Resource Control

19.  Configuring Virtual Networks (Tasks)

20.  Using Link Protection in Virtualized Environments

21.  Managing Network Resources

22.  Monitoring Network Traffic and Resource Usage



IPMP Components in Oracle Solaris

Oracle Solaris IPMP involves the following software:

The multipathing daemon in.mpathd detects interface failures and repairs. The daemon performs both link-based failure detection and probe-based failure detection if test addresses are configured for the underlying interfaces. Depending on the type of failure detection method that is employed, the daemon sets or clears the appropriate flags on the interface to indicate whether the interface failed or has been repaired. As an option, the daemon can also be configured to monitor the availability of all interfaces, including those that are not configured to belong to an IPMP group. For a description of failure detection, see Failure and Repair Detection in IPMP.

The in.mpathd daemon also controls the designation of active interfaces in the IPMP group. The daemon attempts to maintain the same number of active interfaces that was originally configured when the IPMP group was created. Thus in.mpathd activates or deactivates underlying interfaces as needed to be consistent with the administrator's configured policy. For more information about the manner by which the in.mpathd daemon manages activation of underlying interfaces, refer to How IPMP Works. For more information about the daemon, refer to the in.mpathd(1M) man page.

The IP kernel module manages outbound load-spreading by distributing the set of available IP data addresses in the group across the set of available underlying IP interfaces in the group. The module also performs source address selection to manage inbound load-spreading. Both roles of the IP module improve network traffic performance.

The IPMP configuration file /etc/default/mpathd is used to configure the daemon's behavior. For example, you can specify how the daemon performs probe-based failure detection by setting the time duration to probe a target to detect failure, or which interfaces to probe. You can also specify what the status of a failed interface should be after that interface is repaired. You also set the parameters in this file to specify whether the daemon should monitor all IP interfaces in the system, not only those that are configured to belong to IPMP groups. For procedures to modify the configuration file, refer to How to Configure the Behavior of the IPMP Daemon.

The ipmpstat utility provides different types of information about the status of IPMP as a whole. The tool also displays other specific information about the underlying IP interfaces for each group, as well as data and test addresses that have been configured for the group. For more information about the use of this command, see Monitoring IPMP Information and the ipmpstat(1M) man page.