ChorusOS man pages section 1M: System Management Utilities

ping(1M)

NAME

ICMP ECHO_REQUEST

SYNOPSIS

ping

-QRadfnqrv

-c

count

-i

wait

-l

preload

-p

pattern

-P

policy

-s

packetsize

-S

src_addr

-t

timeout

host

-L

-I

interface

-T

ttl

mcast-group

DESCRIPTION

The ping command is also available as a built in command in C_INIT(1M)

The ping uses the ICMP protocol's mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway. ECHO_REQUEST datagrams (pings) have an IP and header, followed by a struct timeval and then an arbitrary number of "pad" bytes used to fill out the packet. The options are as follows:

-a Audible: Include a bell (ASCII 0x07) character in the output when any packet is received. This option is ignored if other format options are present.
-c Count: Stop after sending (and receiving) count ECHO_RESPONSE packets. If this option is not specified, ping will operate until interrupted.
-d: Set the SO_DEBUG option on the socket being used.
-f Flood ping: Output packets as fast as they come back or one hundred times per second, whichever is quicker. For every ECHO_REQUEST sent, a period "." is printed, and for every ECHO_REPLY received, a backspace is printed. This provides a rapid display of how many packets are being dropped. Only the super user may use this option. This can have a negative effect on a network and should be used with caution.
-i Wait: Wait seconds between sending each packet. The default is to wait for one second between each packet. The wait time may be fractional, but only the superuser may specify values less then 1 second. This option is incompatible with the -f option.
-I interface: Source multicast packets with the given interface address. This flag only applies if the ping destination is a multicast address.
-l preload: If preload is specified, ping sends that many packets as fast as possible before falling into its normal mode of behavior. Only the superuser may use this option.
-L: Suppress loopback of multicast packets. This flag only applies if the ping destination is a multicast address.
-n: Numeric output only. No attempt is made to look up symbolic names for host addresses.
-p pattern: You may specify up to 16 pad bytes to fill out the packet you send. This is useful for diagnosing data-dependent problems in a network. For example, -p ff will cause the sent packet to be filled with all 1's.
-P policy: Specifies the IPsec policy for the ping session.
-Q Somewhat quiet output: Do not display ICMP error messages that are in response to our query messages. Originally, the -v flag was required to display such errors, but -v displays all ICMP error messages. On a busy machine, this output can be excessive. Without the -Q flag, ping prints out any ICMP error messages caused by its own ECHO_REQUEST messages.
-q Quiet output: Display nothing except the summary lines at startup time and when finished.
-R Record route: Include the RECORD_ROUTE option in the ECHO_REQUEST packet and display the route buffer on returned packets. Note that the IP header is only large enough for nine such routes. The traceroute(8) command is usually better at determining the route packets take to a particular destination. If more routes come back than should do, for example due to an illegal spoofed packet, ping will print the route list and then truncate it at the correct spot. Many hosts ignore or discard the RECORD_ROUTE option.
-r: Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This option can be used to ping a local host through an interface that has no route through it (e.g., after the interface was dropped by routed(8)).
-s packetsize: Specify the number of data bytes to be sent. The default is 56, which translates into 64 ICMP data bytes when combined with the 8 bytes of ICMP header data. Only the super-user may use this option.
-S src_addr: Use the following IP address as the source address in outgoing packets. On hosts with more than one IP address, this option can be used to force the source address to be something other than the IP address of the interface the probe packet is sent on. If the IP address is not one of this machine's interface addresses, an error is returned and nothing is sent.
-t timeout: Specify a timeout, in seconds, before ping exits regardless of how many packets have been received.
-T ttl: Set the IP Time To Live for multicasted packets. This flag only applies if the ping destination is a multicast address.
-v verbose ouput: Verbose output. ICMP packets other than ECHO_RESPONSE that are received are listed.

When using ping for fault isolation, it should first be run on the local host, to verify that the local network interface is up and running. Then, hosts and gateways further and further away should be"pinged". Round-trip times and packet loss statistics are computed. If duplicate packets are received, they are not included in the packet loss calculation, although the round-trip time of these packets is used in calculating the round-trip time statistics. When the specified number of packets have been sent (and received) or if the program is terminated with a SIGINT, a brief summary is displayed, showing the number of packets sent and received, and the minimum, maximum, mean, and standard deviation of the round-trip times.

This program is intended for use in network testing, measurement and management. Because of the load it can impose on the network, it is unwise to use ping during normal operations or from automated scripts.

ICMP PACKET DETAILS

An IP header without options is 20 bytes. An ICMP ECHO_REQUEST packet contains an additional 8 bytes worth of ICMP header followed by an arbitrary amount of data. When a packetsize is given, this indicated the size of this extra piece of data (the default is 56). Thus the amount of data received inside of an IP packet of type ICMP ECHO_REPLY will always be 8 bytes more than the requested data space (the ICMP header).

If the data space is at least eight bytes large, ping uses the first eight bytes of this space to include a timestamp which it uses in the computation of round-trip times. If less than eight bytes of pad are specified, no round-trip times are given.

DUPLICATE AND DAMAGED PACKETS

Ping will report duplicate and damaged packets. Duplicate packets should never occur when pinging a unicast address, and seem to be caused by inappropriate link-level retransmissions. Duplicates may occur in many situations and are rarely (if ever) a good sign, although the presence of low levels of duplicates may not always be cause for alarm. Duplicates are expected when pinging a broadcast or multicast address, since they are not really duplicates but replies from different hosts to the same request.

Damaged packets are obviously serious cause for alarm and often indicate broken hardware somewhere in the ping packet's path (in the network or in the hosts).

TRYING DIFFERENT DATA PATTERNS

The (inter)network layer should never treat packets differently depending on the data contained in the data portion. Unfortunately, data-dependent problems have been known to sneak into networks and remain undetected for long periods of time. In many cases the particular pattern that will have problems is something that does not have "sufficient transitions", such as all ones or all zeros, or a pattern right at the edge, such as almost all zeros. It is not necessarily enough to specify a data pattern of all zeros (for example) on the command line because the pattern that is of interest is at the data link level, and the relationship between what you type and what the controllers transmit can be complicated.

This means that if you have a data-dependent problem you will probably have to do a lot of testing to find it. If you are lucky, you may manage to find a file that either cannot be sent across your network or that takes much longer to transfer than other similar length files. You can then examine this file for repeated patterns that you can test using the -p option.

TTL DETAILS

The TTL value of an IP packet represents the maximum number of IP routers that the packet can go through before being thrown away. In current practice you can expect each router in the Internet to decrement the TTL field by exactly one.

The TCP/IP specification states that the TTL field for TCP packets should be set to 60, but many systems use smaller values (4.3BSD uses 30, 4.2BSD used 15).

The maximum possible value of this field is 255, and most UNIX systems set the TTL field of ICMP ECHO_REQUEST packets to 255. This is why you will find you can ping some hosts, but not reach them with telnet(1) or ftp(1CC)

In normal operation ping prints the ttl value from the packet it receives. When a remote system receives a ping packet, it can do one of three things with the TTL field in its response:

Not change it; this is what BSD UNIX systems did before the 4.3BSD-Tahoe release. In this case the TTL value in the received packet will be 255 minus the number of routers in the round-trip path.
Set it to 255; this is what current BSD UNIX systems do. In this case the TTL value in the received packet will be 255 minus the number of routers in the path from the remote system to the pinging host.
Set it to some other value. Some machines use the same value for ICMP packets that they use for TCP packets, for example either 30 or 60. Others may use completely wild values.

RETURN VALUES

The ping command returns an exit status of zero if at least one response was heard from the specified host; a status of two if the transmission was successful but no responses were received; or another value (from <sysexits.h>) if an error occurred.

ATTRIBUTES

See attributes(5) for descriptions of the following attributes:

ATTRIBUTE TYPE	ATTRIBUTE VALUE
Interface Stability	Evolving

AUTHORS

The original ping command was written by Mike Muuss at the US Army Ballistics Research Laboratory.

BUGS

Many hosts and gateways ignore the RECORD_ROUTE option.

The maximum IP header length is too small for options such as RECORD_ROUTE to be completely useful. There's not much that can be done about this, however.

Flood pinging is not recommended in general, and flood pinging the broadcast address should only be done under very controlled conditions.

The -v option is not very effective on busy hosts.

ChorusOS 5.0 Last Revised December 2001