C H A P T E R 2 |
Installing and Setting Up the Software |
This chapter contains instructions for installing, setting up, uninstalling, starting, and stopping Sun Fire entry-level midrange systems add-on software using the Sun Management Center Wizards. Refer to the Sun Management Center Installation and Configuration Guide for information about installing, setting up, uninstalling, starting, and stopping the base Sun Management Center software.
This chapter contains the following sections:
Caution - Use the installation scripts and the setup scripts provided with the Sun Management Center software. Do notmanually add packages or manually change configuration files. |
Your Sun Management Center installation and setup scripts or Wizard panels might not display exactly the same messages in exactly the same sequence as the examples shown in this supplement. However, these examples show the basic messages you will receive in approximately the sequence you will receive them. Your actual installation and setup scripts depend on the add-on components you choose to install and other choices you make.
See Appendix A to perform these functions using the command line interface (CLI).
Refer to the Sun Management Center 3.5 Version 6 Release Notes for Sun Fire Entry-Level Midrange Systems for information about obtaining the Sun Management Center 3.5 Version 6 add-on software.
The Sun Management Center add-on software packages for Sun Fire entry-level midrange systems correspond to the architectural layers of Sun Management Center. The following is an overview of these packages:
Provides libraries and other files needed by the Sun Management Center server to monitor supported Sun Fire entry-level midrange systems. This software must be installed on all Sun Management Center server systems in addition to the base Sun Management Center server software.
Provides libraries and other files needed by the Sun Management Center agent to monitor supported Sun Fire entry-level midrange systems. This software must be installed on all Sun Management Center-monitored Sun Fire entry-level midrange systems in addition to the base Sun Management Center agent software.
Provides scripts and Java class files to support graphical user interface (GUI) setup, Agent update, and add-on installation and removal.
The minimum Sun Fire entry-level midrange systems firmware and operating systems supported in this release are described in the Sun Management Center 3.5 Version 6 Release Notes for Sun Fire Entry-Level Midrange Systems. Refer to that document also to learn about recommended patches for this release.
The dynamic reconfiguration (DR) add-on included in the Sun Management Center product does not work with Sun Fire entry-level midrange systems. Therefore, do not load the DR software on Sun Fire agents supported by this add-on.
Before beginning the add-on software installation process, you should know which systems in your network will function as servers and consoles, and which Sun Fire entry-level midrange systems will be monitored by the servers and consoles.
For Sun Management Center software installation instructions, please refer to the Sun Management Center Software User's Guide and the Sun Management Center Software Release Notes, or consult the Sun Management Center web site for instructions:
http://www.sun.com/sunmanagementcenter
The following four steps comprise an overview of the installation process described in the remainder of this chapter.
1. If you have been managing Sun Fire V1280 systems using the Sun Management Center add-on software for Netra systems, you must remove the existing agent software from the Sun Fire V1280 systems. See Updating Existing Netra Software on the Sun Fire V1280.
2. Ensure that you have installed the latest update for Sun Management Center 3.5 base software, plus any other add-on software you require. See Upgrading to Sun Management Center 3.5 Update 1 Software.
3. Install Sun Management Center 3.5 Version 6 Software for Sun Fire entry-level midrange systems. See Installing and Setting Up New Sun Management Center 3.5 Update 1 Add-On Software Using the Install Wizard.
4. Set up all newly installed base and add-on software. See Setting Up the Sun Fire Entry-Level Midrange Systems Add-On Software Using the Setup Wizard.
5. Start the base and add-on software.
If you have been managing Sun Fire V1280 systems using the Sun Management Center add-on software for Netra systems, you must remove the existing agent software from the Sun Fire V1280 systems, then install and set up Sun Management Center 3.5 Version 6 add-on software in its place. You do not have to remove the server-specific add-on software for Netra systems from the Sun Management Center server host if it is required to support any other platforms for which you use it.
To Update Existing Sun Management Center 3.5 Add-On Software for Netra Systems |
1. Remove the existing Netra add-on software from the Sun Fire V1280 agent.
See the following references depending on whether you are using the CLI or GUI:
2. Install and set up the new add-on software for Sun Fire entry-level midrange systems on the server and domains.
See the following references depending on whether you are using the CLI or GUI:
Note - Installing Netra add-on software after SunFire entry-level midrange systems add-ons have been installed is unsupported. |
Refer to the Sun Management Center 3.5 Update 1 Supplement for information about upgrading from Sun Management Center 3.5 software or earlier to 3.5 Update 1 core software. Refer to the Sun Management Center 3.5 Version 6 Release Notes for Sun Fire Entry-Level Midrange Systems for information about software requirements for your system and to the latest version of Sun Management Center Release Notes for your version of the core software.
This section provides a summary of installing the latest version of Sun Management Center 3.5 base software and Sun Fire entry-level midrange systems add-on software using the Install Wizard. Chapter 6, Installation and Setup, of the Sun Management Center Installation and Configuration Guide, describes in detail how to install all the software. If you prefer to use the command-line interface (CLI), see Appendix A.
To Install the Software |
You can install the console, server, and agent layers either separately or in combination.
1. Log in as superuser on the host machine.
2. Change the directory to the path/sbin directory, where path is the location of the Sun Management Center 3.5 CD or the disk copy of the CD.
3. Install the Sun Management Center 3.5 base software using the es-guiinst script.
4. Change to the directory where you installed the base software in Step 3 (installed_directory/SUNWsymon/sbin).
5. Run the es-guiinst script again with a pointer to the path where you placed the Sun Fire entry-level midrange systems add-on software for Version 6. Use the disk1 image (addon_path/disk1/image).
A list of add-on products you can install is displayed.
6. Select the Sun Fire Entry-Level Midrange Systems add-on software, and click Next.
This section describes how to set up the Sun Fire entry-level midrange systems using the Sun Management Center Setup Wizard. For more details about the entire software setup process, refer to Chapter 6, "Installation and Setup," of the Sun Management Center Installation and Configuration Guide.
To Set Up the Add-On Software Using the Wizard GUI |
Set up the add-on software both on the Sun Management Center server and on the Sun Fire entry-level midrange systems where you will be running the software.
1. Type es-guisetup on the system where the add-on software is installed to start the Sun Management Center Setup Wizard.
Once the Sun Management Center base software setup is complete, the Wizard displays the following message:
2. Click Next to start the setup procedure.
The Sun Fire entry-level midrange systems Setup panel displays the following message:
Updating configuration files... Status: Updating configuration files... Update of configuration files complete. |
The Sun Fire entry-level midrange systems Setup panel displays the following message:
The base Sun Management Center Setup Wizard provides these advanced setup options when the current Sun Management Center installation is already configured:
Note - Use the Reconfigure All option instead of the Remove Setup Configuration option at this time. |
Refer to the Sun Management Center Installation and Configuration Guide for more information about using these options.
Copyright © 2005, Sun Microsystems, Inc. All Rights Reserved.