Figures

FIGURE 1-1 Front Panel Components

FIGURE 1-2 Rotating Service Module - Miscellaneous Internal Components and Rear Panel Components

FIGURE 1-3 Hardware Cryptographic Module and Memory

FIGURE 1-4 Processor Fans and Heat Sink Assemblies on a Replacement System Board

FIGURE 1-5 Location of the Front Panel Indicators

FIGURE 1-6 Hard Drive Indicators

FIGURE 1-7 Rear Panel Indicators

FIGURE 1-8 Ethernet Network Indicators

FIGURE 2-1 Netra 240 Server Tip Hazard

FIGURE 2-2 On/Standby Button and Rotary Switch

FIGURE 2-3 Rotary Switch Positions

FIGURE 2-4 Finger Holds on the Bezel

FIGURE 2-5 Removing the Server Cover

FIGURE 2-6 Two Methods of Hanging the Detached Cover on a Netra 240 Server

FIGURE 2-7 Opening the Rotating Service Module

FIGURE 2-8 Grounding Point in the Server

FIGURE 3-1 Finger Holds on the Bezel

FIGURE 3-2 Disconnecting the Bezel Cables

FIGURE 3-3 Removing and Replacing the Air Filter From the Bezel

FIGURE 3-4 Removing and Inserting a System Configuration Card

FIGURE 3-5 Removing and Installing a Hard Drive

FIGURE 3-6 Removing a DVD Drive

FIGURE 3-7 Location of the DVD Drive Slot With a Filler Panel

FIGURE 3-8 Removing a Power Supply Unit

FIGURE 4-1 Removing the Alarm Board

FIGURE 4-2 Removing the Front Fan Assembly Tray

FIGURE 4-3 Removing the SCSI Interface Board

FIGURE 4-4 Lifting the SCSI/IDE Cable Clamp

FIGURE 4-5 Removing the SCSI Interface Board Cable and the IDE Cable From the System Board

FIGURE 4-6 Removing the System Configuration Card Reader Cluster

FIGURE 5-1 Removing/Rotating the Air Duct and Rear Fan Assembly

FIGURE 5-2 System Board CPUs and Corresponding Memory Locations

FIGURE 5-3 Removing and Inserting Memory

FIGURE 5-4 Location of the PCI Lockdown Screw

FIGURE 5-5 Location of the PCI Lockdown Bracket

FIGURE 5-6 Removing and Installing the Upper Half-Length PCI Cards

FIGURE 5-7 Removing and Installing the Lower Full-Length PCI Card

FIGURE 5-8 Removing the Power Distribution Board

FIGURE 5-9 Disengaging a Power Supply Unit

FIGURE 5-10 Removing and Installing the Hardware Cryptographic Module

FIGURE 5-11 Removing the PCI Riser Card Assembly

FIGURE 5-12 Disconnecting the PDB Wiring Harness From the System Board

FIGURE 5-13 Lifting the SCSI/IDE Cable Clamp

FIGURE 5-14 Removing the SCSI Interface Board Cable and the IDE Cable From the System Board

FIGURE 5-15 Detaching the Front Fan Assembly Cables From the System Board Connectors

FIGURE 5-16 Removing the DB-9 and SCSI Jackposts From the Server

FIGURE 5-17 Removing and Installing a System Board

FIGURE 5-18 Location of the CPU Heat Sink Assemblies

FIGURE 5-19 Detaching the Fan Power Cables

FIGURE 5-20 Unlocking the Heat Sink Fasteners

FIGURE 5-21 Lifting the Heat Sink From the CPU Socket

FIGURE 5-22 Removing the Heat Sink Fans

FIGURE 5-23 Replacing the Heat Sink on the CPU Socket

FIGURE 6-1 Location of Jumpers on the Netra 240 System Board

FIGURE A-1 Illustrated Parts Breakdown, Front Panel Components

FIGURE A-2 Rotating Service Module, Internal and Rear Panel Components

FIGURE A-3 Illustrated Parts Breakdown, Miscellaneous Internal Components

FIGURE B-1 Gigabit Ethernet Port Pin Numbering

FIGURE B-2 Network Management Port Pin Numbering

FIGURE B-3 Serial Management Port Pin Numbering

FIGURE B-4 Serial Port (10101) Pin Numbering

FIGURE B-5 Alarm Port Pin Numbering

FIGURE B-6 USB Ports Pin Numbering

FIGURE B-7 SCSI Port Pin Numbering

FIGURE C-1 Location of the System Configuration Card