C H A P T E R 7 |
Managing the ILOM Using the WebGUI |
This chapter describes how to use the WebGUI to perform monitoring and maintenance.
It includes the following sections:
This section describes how to configure the ILOM serial port. Use this procedure only when you need to change the serial port settings. The default settings are 9600 baud and no flow control.
The serial port provides access to the WebGUI, the command-line interface (CLI), and the system console stream using serial port redirection.
Note - Normally, the console matches the ILOM's default settings (9600 baud, 8N1 [eight data bits, no parity, one stop bit], no flow control). |
1. Log in to the ILOM as administrator.
2. Select Configuration => Serial Port.
The Serial Port Settings page appears.
FIGURE 7-1 Serial Port Settings Page
3. Select the baud rate for the internal serial port from the Internal Serial Port drop-down menu.
This setting must match the setting for serial port 0, COM1 or /dev/ttyS0 on the host operating system.
The baud rate value must match the speed that was specified for the BIOS serial redirection feature (default is 9600 baud) and the speed used for the boot loader and operating system configuration.
To connect to the system console using the ILOM, the ILOM must be set to its default settings (9600 baud, 8N1 [eight data bits, no parity, one stop bit], no flow control).
4. Select the baud rate for the external serial port from the External Serial Port drop-down menu.
This setting must match the baud rate on the RJ-45 serial port on the Sun server.
5. Click Save for your changes to take effect, or click Cancel to return to the previous settings.
This section describes how to configure the network parameters for the ILOM.
The ILOM automatically configures its IP settings using the Dynamic Host Configuration Protocol (DHCP). If your network does not support this protocol, you need to set the parameters manually.
1. Log in to the ILOM as administrator.
2. Select Configuration => Network.
The Network Settings page appears.
FIGURE 7-2 Network Settings Page
3. Complete the information in the Network Settings page.
Use the descriptions in TABLE 7-1 when completing the information.
4. Click Save for your settings to take effect.
Note - Changing the IP address ends your ILOM session.
|
You are prompted to close your web browser.
5. Log back in to the ILOM using the new IP address.
Note - If you changed the network settings, you must log back in with a new browser session. |
This section describes how to set the ILOM clock manually or to synchronize the ILOM date and time with a Network Time Protocol (NTP) server.
The ILOM clock is described in Section 7.3.3, Interpreting ILOM Clock Settings.
Before you begin, obtain IP addresses of the NTP servers you want to use.
1. Log in to the ILOM as administrator.
2. Select Configuration => Clock Settings.
The Clock Settings page appears.
FIGURE 7-3 Clock Settings Page
3. Type a date in the Date field.
The date format is mm/dd/yyyy.
4. Set the hour and minute using the drop-down menus.
5. Click Save for your changes to take effect.
1. Log in to the ILOM as administrator.
2. Select Configuration => Clock Settings.
The Clock Settings page appears. See FIGURE 7-3.
3. Select the Enable check box next to Synchronize Time Using NTP.
4. Type the IP addresses of the NTP servers you want to use.
5. Click Save for your changes to take effect.
When the ILOM reboots, the ILOM clock is set to Thu Jan 1 00:00:00 UTC 1970. The ILOM reboots as a result of the following:
After an ILOM reboot, the ILOM clock is changed by the following:
1. Log in to the ILOM as administrator or operator.
2. Select Maintenance => Reset SP.
The Reset Service Processor page appears.
FIGURE 7-4 Reset Service Processor Page
3. Click Reset SP to reset the ILOM.
The ILOM reboots. The WebGUI is unavailable while the ILOM reboots.
This procedure causes the ILOM to reset the administration password and clear the BIOS password.
This procedure requires changing a hardware jumper in your server enclosure. See your service manual for details.
Both the ILOM and BIOS firmware are tightly coupled and are always updated together. A single firmware image contains both the ILOM and BIOS firmware.
Occasionally, you might need to downgrade your firmware. Downgrading is done exactly the same as upgrading, only you choose an older (downgraded) image in Step 7.
|
Caution - Shut down your host operating system before proceeding. Otherwise the ILOM will shut the host down ungracefully, which could cause file system corruption. |
Note - The upgrade takes about five minutes to complete. During this time, no other tasks can be performed in the ILOM.
|
1. Log in to the ILOM as administrator.
2. Ensure that you can access the new flash image on the client machine that you are using to update the ILOM.
3. If the server OS is running, perform a clean shutdown.
4. Select Maintenance => Firmware Upgrade.
The Upgrade the Firmware page appears.
|
Caution - Do not close the WebGUI using the Log Out button in the web browser when the ILOM is in Upgrade mode. If you must close the WebGUI, use the WebGUI's Cancel button. |
FIGURE 7-5 Firmware Upgrade Page
A dialog box appears. It asks you to confirm that you want to enter Upgrade mode.
6. Click OK to enter Upgrade mode.
The ILOM stops its normal operation and prepares for a flash upgrade.
7. Type the path to the new ILOM flash image file in the Select Image File to Upload field, or click Browse to locate and select the firmware update file (*.ima).
The Upgrade wizard copies the selected file into the ILOM's DRAM, and then verifies that the copy procedure was successful. This takes about one minute with a fast network connection.
The system displays a confirmation dialog box.
Note - A network failure during the file upload will result in a time out and the ILOM will reboot with the prior version of the ILOM firmware. |
The Verify Firmware Image page appears.
FIGURE 7-7 Verify Firmware Image Page
10. Select Preserve Configuration to keep your ILOM settings. Otherwise, they will be overwritten.
11. Click Start Upgrade, or click Cancel to stop the upgrade.
If you clicked Start Update, a progress screen indicates that the firmware image is being upgraded. Once the upgrade progress reaches 100%, the firmware upgrade is complete.
After the upgrade operation has completed successfully, the ILOM will automatically reboot. This is done so that the image upgrade can take effect.
A screen prompt might ask you to repeat the upgrade. This is not due to any problem. If this happens, repeat the procedure, starting at Step 1.
Note - You cannot perform any other operation within your current web browser session. |
12. Close your web browser and reconnect to the ILOM.
Note - If the configuration is not preserved, enter BIOS setup and save the optimal default settings. |
This section describes how to view and modify web server settings.
ILOM provides the option to control access to the web interface. There are four choices:
1. Log in to the ILOM as administrator.
2. Select Configuration => System Management Access =>Web Server.
The Web Server Settings page appears.
FIGURE 7-8 Web Server Settings Page
3. Select the HTTP or HTTPS web server.
The HTTPS web server is enabled by default.
Note - If you disable HTTP or select Redirect HTTP Connection to HTTPs, and then disable HTTPS, you will be unable to access the WebGUI. To restore access, use the CLI /SP/services/http or https commands, as described in Section 6.7, Enabling HTTP or HTTPS Web Access. |
4. Assign an HTTP or HTTPS port number.
5. Click Save to save your settings.
This section describes how to upload a Secure Sockets Layer (SSL) certificate and SSL private key to use when accessing the ILOM.
To establish a secure HTTPS connection to the ILOM, you must upload an SSL certificate and a private key into the ILOM. These two together help provide a secure connection to the correct server when using HTTPS. Ensure that the uploaded SSL certificate and private key match. If they do not match, secure access may not work properly.
1. Log in to the ILOM as administrator.
2. Select Configuration => System Management Access => SSL Certificate.
The SSL Certificate Upload page appears.
FIGURE 7-9 SSL Certificate Upload Page
3. Type the file name of the new SSL certificate, or click Browse to search for a new SSL certificate.
The file name has a .pem file extension. The ILOM does not support pass-phrase encrypted certificates.
4. Click Upload to upload the selected SSL certificate.
The SSL Certificate Upload Status dialog appears.
5. Once you have uploaded the certificate and private key, click OK to reset the ILOM immediately, or click Cancel to reset the ILOM later.
The ILOM must be reset for the new certificate to take effect. If you click OK, you must close your web browser and reconnect to the ILOM. HTTPS is enabled by default.
You can now access the ILOM securely, using the following format in your IP Address field from your web browser:
For example, if the ILOM's IP address is 192.168.0.30, type the following:
This section describes how to set the timeout period for your ILOM session. Once you set the timeout period, if your session is inactive for that amount of time, you will be automatically logged out of the session.
1. Log in to the ILOM as administrator or operator.
2. Select System Information => Session Time-Out.
The Session Time-out page appears.
FIGURE 7-10 Session Time-Out Page
3. From the Session Time-Out drop-down list, select the amount of time for the session time-out period.
A confirmation dialog box appears.
The session timeout period is set to the selected amount of time. If you exceed the amount of time set for your session, you are automatically logged out of the WebGUI.
This section describes how to view all active connections to the ILOM.
1. Log in to the ILOM as administrator or operator.
2. Select User Management => Active Sessions.
The Active Sessions page appears. The information on this page includes the user name, the date and time that the user initiated the session, and the type of session (web or command shell).
FIGURE 7-11 Active Sessions Page
Copyright © 2007, Sun Microsystems, Inc. All Rights Reserved.