A SCSI Drive Failed (Ch:%d,Id:%d). Replace the defective drive.
|
A tape has been left in the autoloader by a previous hardware fault. Insert an empty magazine to clear the fault. If the fault does not clear, turn the autoloader off and then on again. If the problem persists, call the tape drive supplier helpline.
|
A user named ssconfig must be created for configuring SUNWsscs Diag Reporter.
|
Abort Clone SCSI Drive.
|
Abort Initialization.
|
Abort Parity Check.
|
Abort Rebuild.
|
Access denied for one or more servers. Log in as ssconfig user, and then try the operation again.
|
Access denied for one or more servers. Please log in as an ssadmin user and then try the operation again.
|
Active trap events is empty.
|
Add Physical drive %d:%d has started on logical drive LogicalDrive.
|
Add Physical drive has completed on logical drive LogicalDrive.
|
Add SCSI Drive into Logical Drive information.
|
Agent Name is empty.
|
An error occurred while getting data from the server.
|
An HBA card with this WWN already exists.
|
Another instance of this program is already running!
|
Array Admin in Progress.
|
At least one email address needs to be configured.
|
Attempted to load a cartridge type, not supported by this drive. The cartridge has been automatically ejected. Attempted to load an unsupported tape format.
|
Attempted to write to a write-protected cartridge. Remove the write-protection or use another tape.
|
Audible alarm has an unknown status
|
Audible alarm has been triggered.
|
Audible alarm has been turned off.
|
Background check or rebuild operation in progress.
|
Background initialization in progress.
|
Background parity check in progress.
|
Background rebuild operation in progress.
|
Battery Expiration Monitoring of (Ch:%d,Id:%d) is not available.
|
Cannot accept the incoming connection.
|
Cannot allocate memory.
|
Cannot bind TCP port with the opened TCP/IP communication.
|
Cannot connect with the incoming connection.
|
Cannot create a communication session for the incoming connection.
|
Cannot create host LUN filter; no host IDs were selected.
|
Cannot create standard host LUN mapping, no host IDs were selected.
|
Cannot find the logical drive that was just created. It may have been aborted.
|
Cannot get configuration from controller. The operation is canceled.
|
Cannot get configuration in set configuration.
|
Cannot listen on the opened TCP/IP communication.
|
Cannot lock a resource.
|
Cannot open TCP/IP communication.
|
Cannot perform IOCTL on the TCP/IP communication.
|
Cannot query incoming data status of the connection.
|
Cannot receive data from the connected client.
|
Cannot report status.
|
Cannot send data to the connected client.
|
Change logical drive failure.
|
Change logical volume failure.
|
Change or set local/global standby drives successful.
|
Changes made to Optimization will NOT take effect until all the logical drives are deleted and then the controller is RESET.
|
Click View to select one file.
|
Close transport fail at set configuration.
|
Collect mail canceled by user.
|
Communication is reestablished with controller.
|
Configuration information saved successfully!
|
Connect and Login command error
|
Contact Fax number format is wrong.
|
Contact Name is empty
|
Contact Phone number format is wrong.
|
Continue add drv on logical drive LogicalDrive.
|
Continue Media Check on Physical Drive %d:%d.
|
Controller Event, Battery %s %s. Informational message.
|
Controller Event, Battery %s %s. Likely battery module error or power cycle of array. If error persists, replace defective battery module.
|
Controller has been reset.
|
Controller has been shut down.
|
Controllers back in redundancy mode!
|
Controllers back in redundancy mode!
|
Copy & Replace has completed on Physical drive %d:%d.
|
Copy & Replace has started from Physical drive %d:%d to %d:%d.
|
Copy & Replace on Physical drive %d:%d has been aborted.
|
Create logical drive failure.
|
Create logical volume failure.
|
Creating Host LUN filter Entry; please wait...
|
Creating standard Host LUN mapping; please wait...
|
Customer Fax number format is wrong.
|
Customer Name is empty.
|
Customer Phone number format is wrong.
|
Data is at risk. Media performance of this tape is severely degraded. Copy any data you require from this tape. Do not use this tape again. Restart the operation with a different tape.
|
Decrypt mail canceled by user.
|
Delete logical drive failure.
|
Delete logical volume failure.
|
Deleted disk successfully!
|
Deleting disk; please wait...
|
Deleting Host LUN filter Entry; please wait...
|
Deleting standard Host LUN mapping; please wait...
|
Device at [Channel:Target] has failed the self-reliability test.
|
Device information failed.
|
Disk(%d.%d) has changed from %s state to %s state.
|
Disk is labeled successfully.
|
Door lock has an unknown status.
|
Door locked.
|
Door unlocked.
|
Download Firmware with Boot Record.
|
Downloading Firmware to the devices
|
Downloading Firmware to the RAID Controller.
|
Drive SCSI Ch:%d; Id:%d Likely poorly seated or defective drive. If random drives, possible I/O module or cable failure.
|
Email address format is wrong.
|
Enclosure #Enclosure state change: Information: [x}
x is the raw data of SAFTE/SES data in hexadecimal format.
|
Enclosure #Enclosure, temperature threshold has changed from a State state to a State state. Information:
|
Engaging firmware; a controller reset is not necessary.
|
Error in writing file, please try later!
|
Error occurred. Reset the config file.
|
Expand LD/LV information.
|
Expand logical volume successfully.
|
Expansion has completed on logical drive LogicalDrive.
|
Expansion has started on logical drive LogicalDrive.
|
Expansion logical drive LogicalDrive has been aborted.
|
Fan #Fan has an unknown status.
|
Fan #Fan is malfunctioning.
|
Fan #Fan is not present in the system.
|
Fan #Fan is operational.
|
File I/O error. Configuration could not be restored!
|
Firmware downloaded to SAF-TE/SES device (Ch:%d,Id:%d) failed.
|
Firmware downloaded to SAF-TE/SES device (Ch:%d,Id:%d) successfully.
|
Firmware downloaded to SCSI drive (Ch:%d,Id:%d) failed.
|
Firmware downloaded to SCSI drive (Ch:%d,Id:%d) successfully.
|
First select one Logical Drive!
|
First select one physical device.
|
First select one RAID controller.
|
For RAID1 Logical Drive 'Add Drive'/'Copy and Replace' function is disabled.
|
Forward mail canceled by user.
|
Generic File Mutex lock is not released.
|
Get logical drive list failure.
|
Getting Agent Options failed!
|
Getting Controller Parameters failed!
|
Getting Host LUN Assignments failed! Please try again
|
Getting the configuration failed!
|
Group Name can not be empty
|
Host LUN filter Entry created successfully!
|
Host LUN filter Entry deleted successfully!
|
Host LUNs modified successfully.
|
If file access is not properly coordinated when assigned to multiple hosts, data corruption and access contentions may occur.
|
If Minimum interval is \“0\” or \“*\”, then Content must be \“Event\”
|
If the firmware download progress is interrupted the controllers/devices may become unusable.
|
Initialization has completed on logical drive LogicalDrive.
|
Initialization has started on logical drive LogicalDrive.
|
Initialization on logical drive LogicalDrive has been aborted.
|
Initialization operations have completed.
|
Initialization, rebuild, expand, or add SCSI drive activities are in progress. Try again later.
|
Inserted failed primary controller.
|
Inserted failed secondary controller.
|
Invalid data received.
|
Invalid server IP address!
|
IOM SES Firmware Revision Level Mismatch (LogChl:%d,Id:%d). ses version=%s/%s, pld version=%s/%s. [CHASSIS BKPLN SN#%s}
|
IP Address format error (must be xxx.xxx.xxx.xxx and 0 < xxx <255) !
|
IP Address is duplicated!
|
IP Address is empty.
|
Location is empty.
|
Log in as \“ssconfig”\ user and try the operation again.
|
Logical array LogicalArray has changed from a state state to a state state.
|
Logical Drive ID %d exceeds 2 TB size limitation for sequential optimized LD.
|
Logical Drive ID %d exceeds 512 GB size limitation for random optimized LD.
|
Logical Drive ID %d, Rebuild Aborted. Informational message.
|
Logical Drive ID LogicalDrive rebuild has aborted.
|
Logical Drive ID LogicalDrive rebuild has completed.
|
Logical Drive ID LogicalDrive rebuild has started.
|
Logical Drive LogicalDrive has changed from a State state to a State state.
|
Logical Drive LogicalDrive has changed from a State state to a State state.
|
Logical Volume Components List. Total disks in this Logical Volume=
|
Login successful
|
Login unsuccessful
|
Logout command error.
|
Mail information is empty
|
Media Check has completed on Physical drive %d:%d.
|
Media Check has started on Physical drive %d:%d.
|
Media Check on Physical drive %d:%d has been aborted.
|
Memory Allocation Error. Unable to load daemon.
|
Minimum interval between emails must be one of the following formats: \“*\” \“0\”
“\nn\” \“nn:mm\”
|
Minimum interval can’t meet Content value.
|
Minimum interval format error.
|
Minimum interval format is HH[:MM].
|
Minimum interval is empty.
|
Monitor Stopped.
|
Multiple IP assignment mechanisms are not supported. Select only one mechanism.
|
Mute beeper.
|
Mute controller beeper failure.
|
Mute controller beeper.
|
Mutex Lock is not released.
|
Mutex Lock timeouts.
|
Mutex Lock(s) cannot be created!
|
Mutex Lock(s) change state failed!
|
New parity check schedule has been created.
|
No admin progress exists.
|
No Admin progress was found. All activity should be complete!
|
No array administration activity in progress!
|
No more events to report.
|
No new controller was found; you do not need to reboot the system.
|
No online server, cannot delete event log.
|
No rebuildable drive available.
|
Only the last partition of a LD/LV can be deleted.
|
Open transport fail at set configuration.
|
Open transport, Lock fail, the original lock holder’s IP address is %s.
|
Open transport, LogIn fail.
|
Operation completed successfully.
|
Operation failed.
|
Operation in progress.
|
Operation on one of the servers failed.
|
Out of the scope!
|
Parity Check Aborted.
|
Parity check confirmation.
|
Parity check could not be started on logical drive LogicalDrive.
|
Parity check has completed on logical drive LogicalDrive.
|
Parity check has started on logical drive LogicalDrive.
|
Parity check on logical drive LogicalDrive has been aborted.
|
Parity check schedule has been removed.
|
Parity check schedule has been updated.
|
Partition 0 cannot be deleted.
|
Partition table is full. New partitions cannot be added.
|
Password error!
|
Password is empty.
|
Port is invalid (port must be between 0 and 65535).
|
Port is invalid (port must be between 1270 and 1273).
|
Power supply #Power has an unknown status.
|
Power supply #Power is malfunctioning and has been switched off.
|
Power supply #Power is malfunctioning or disabled.
|
Power supply #Power is not present in the system.
|
Power supply #Power is operational but disabled.
|
Power supply #Power is operational.
|
Power supply #Power is present in the system.
|
Primary controller failed!
|
Probe Agent command error!
|
Progress Not Available.
|
RAID Controller firmware checksum failed - corrupt firmware data.
|
RAID Controller firmware download has failed.
|
RAID Controller firmware has been updated.
|
RAID Controller is back online.
|
Read config file error.
|
Rebuild on logical drive LogicalDrive has been aborted.
|
Rebuild or check operations have completed.
|
Redundant Array State Change: Controller Failed.
|
Redundant Array State Change: Controllers Back in Redundancy Mode.
|
Removed a failed primary controller.
|
Removed a failed secondary controller.
|
Restoring configuration to the controller.
|
Retry the configuration operation after the update is complete.
|
SAF-TE/SES card Channel:Target firmware has been updated.
|
SAF-TE/SES card Channel:Target global status has been updated.
|
SAF-TE/SES card Channel:Target slot perform status has been updated.
|
SAF-TE/SES card Channel:Target slot status has been updated.
|
Save a Copy in server.
|
Saving configuration information; please wait...
|
Scan SCSI drive (%d.%d) has succeeded.
|
Scan SCSI Drive information.
|
Scheduled parity check could not be started on logical drive LogicalDrive.
|
Scheduled parity check has completed on logical drive LogicalDrive.
|
Scheduled parity check has started on logical drive LogicalDrive.
|
Scheduled parity check skipped to next schedule due to incompletion of previous check.
|
Secondary controller failed!
|
Server Error.
|
Server failed the operation due to insufficient memory.
|
Server Name is empty.
|
Server Not managed!
|
Set controller parameter(s) successful.
|
Set or add configuration failed.
|
Slot #Slot has had a device Name.
|
SMTP From address format is wrong or empty.
|
SMTP From address format is wrong.
|
SMTP Server address is empty.
|
Specify how often you want the parity checked.
|
Standard Configuration options provide a group of basic default RAID sets whereby the drive size, quantity, and assignments are preconfigured.
|
Standard Configuration will replace the existing configuration.
|
Standard Host LUN mapping created successfully!
|
Standard Host LUN mapping deleted successfully!
|
Standard maps are available to all connected hosts in certain configurations.
|
Standby rebuild operation completed with an unknown error.
|
Standby rebuild operation in progress.
|
Startup state of the secondary controller.
|
State Change Mutex lock is not released.
|
Sun StorEdge Configuration Service monitor daemon has started.
|
Sun StorEdge Configuration Service server daemon has started.
|
Sun StorEdge Configuration Service startup is complete.
|
Sun StorEdge Configuration Service trap daemon has started.
|
System Administrator (ssconfig) has started irrevocable System Shutdown and Restart. SAVE all data and LOG OFF IMMEDIATELY.
|
System ID is empty.
|
Tape operation has stopped because an error occurred while reading or writing data, which the drive cannot correct.
|
TapeAlert notification. Device [Channel:Target].
|
Target Media Error Reported (Ch:%d,Id:%d). Likely poorly seated or defective drive. Possible defective drive slot.
|
Temperature change from TemperatureC to TemperatureC.
|
The background command (s) has finished.
|
The background command(s) has been aborted.
|
The battery on (Ch:%d,Id:%d) is expired on %s. Please install a new battery. Battery Information is (%s).
|
The battery on (Ch:%d,Id:%d) is going to expire on %s (after %d days). Please install a new battery before the current battery expires. Battery Information is (%s).
|
The changer mechanism is having difficulty communicating with the tape drive. Turn the autoloader off then on and restart the operation. If the problem persists, call the tape drive supplier helpline.
|
The configuration has been updated.
|
The configuration was successfully updated. If new LDs/LVs were created, the server may need to be rebooted.
|
The Controller devices list changed.
|
The controller parameters have been updated.
|
The current user is ssconfig; you cannot log in again.
|
The daemons are not responding.
|
The device does not belong to the same HBA card. The operations cannot continue.
|
The disks list changed.
|
The drive letter (mounted point) cannot be assigned.
|
The encrypt key is empty.
|
The firmware does not support multiple IP assignment mechanisms.
|
The firmware download failed because you have tried to use the incorrect firmware for this tape drive. Obtain the correct firmware and try again.
|
The Host LUN filter map (StorEdge SN#%d LD %d Partition %d WWN:) has been created.
|
The Host LUN filter map (StorEdge SN#%d LD %d Partition %d WWN:) has been deleted.
|
The in-service date(%s) of new battery on (Ch:%d,Id:%d) is set.
|
The IP Address cannot be empty.
|
The last cleaning cartridge used in the tape drive has worn out. Discard the worn out cleaning cartridge, wait for the current operation to finish, and then use a new cleaning cartridge.
|
The LD# is moved up after you delete the LD, so it may not be consistent with the LD# shown in the RS-232 terminal window.
|
The length of the Encrypt Key must be greater than 8 characters.
|
The Mail Server field cannot be empty.
|
The media has exceeded its specified life.
|
The memory allocation Failed.
|
The mount point (drive letter) cannot be written into file (registry).
|
The new battery on (Ch:%d,Id:%d) is installed. Battery information is (%s).
|
The number of logical drives did not increase after creating a logical drive. (before:%d now:%d).
|
The operation failed because the autoloader door is open. Clear any obstructions from the autoloader door, eject the magazine, and then insert it again. If the fault does not clear, turn the autoloader off and then on again.
|
The operation failed because the tape in the drive has snapped. Discard the old tape. Restart the operation with a different tape.
|
The Selected Device list is empty!
|
The server already exists!
|
The Server Name cannot be empty or only contain any extra spaces.
|
The server you selected might have already been shut down.
|
The set configuration failed because there is another conflicting operation.
|
The set configuration Failed.
|
The WWN must be a Hex string that is less than 16 characters.
|
There are no available disks to configure.
|
There are no LDs/LVs to manage.
|
There are not enough available disks to add a new LD/LV or there are no available LDs to create a LV. LDs must be unmapped and partitions must be deleted prior to being used in LVs.
|
There is a map to more than one Host, therefore, the \“Map to Multiple Hosts”\ property cannot be unchecked. Remove the map to multiple hosts before changing this setting.
|
There is a problem with the autoloader mechanism. Loader mechanism has detected a hardware fault.
|
There is no spare or replacement drive. Rebuild cannot continue.
|
This may cause data loss.
|
This operation can take up to one minute.
|
This operation might take several seconds. Please wait...
|
This operation will add to the existing configuration.
|
This operation will erase any existing configuration and data.
|
Unable to allocate memory for array inquiry. Unable to monitor this array.
|
Unable to determine local host, terminating!
|
Unable to eject cartridge because the tape drive is in use. Wait until the operation is complete before ejecting the cartridge.
|
Unable to inquire RAID controller.
|
Unable to inquire SAF-TE device. SAF-TE monitoring for this enclosure disabled.
|
Unable to inquire tape device. This device will be removed.
|
Unable to issue Self-Reliability Query on device at [Channel:Target].
|
Unable to log events.
|
Unable to open bindings file -or- no bindings present. Check Bindings file.
|
Unable to open I/O transport layer
|
Unable to query TapeAlert log data. TapeAlert monitoring disabled for this device.
|
Unable to read license data.
|
Unable to read response from SMTP server.
|
Unable to send e-mail to SMTP server.
|
Unable to toggle the speaker on the SAF-TE/SES managed enclosure.
|
Unable to validate recipient at SMTP server.
|
Unable to write license data.
|
UNMAPPED LUN, NOT AVAILABLE TO HOST
|
Username is empty.
|
Wait for mutex failed.
|
Write config file error.
|
Wrong Fax number format.
|
Wrong Phone number format.
|
You must first delete the host mapping for the partitions whose index number is greater before you can change this partition.
|
You must first delete the host mapping for this LD/LV before you can delete it.
|
You must first delete the host mapping of the last partition before you can add a new partition.
|
You must have superuser administrator privileges to run this program. exiting...
|