This task includes the following troubleshooting procedures to try when you submit a print request to a printer and nothing prints:
Check the hardware ("To check the hardware:").
Check the network ("To check the network:").
Check the LP print service basic functions ("To check the basic functions of the LP print service: ").
Check printing from a SunOS 5.8 print client to a SunOS 5.8 print server ("To check printing from a SunOS 5.8 print client to a SunOS 5.8 print server:").
Check printing from a SunOS 5.8 print client to a SunOS 4.1 print server ("To check printing from a SunOS 5.8 print client to a SunOS 4.1 print server:").
Check printing from a SunOS 4.1 print client to a SunOS 5.8 print server ("To check printing from a SunOS 4.1 client to a SunOS 5.8 print server: ").
Try the first three procedures in the order in which they are listed, before going to the specific print client/server case that applies. However, if the banner page prints, but nothing else does, turn to the instructions under "How to Troubleshoot Incorrect Output".
Check that the printer is plugged in and turned on.
Check that the cable is connected to the port on the printer and to the port on the system or server.
Make sure that the cable is the correct cable and that it is not defective.
Refer to the manufacturer`s documentation. If the printer is connected to a serial port, verify that the cable supports hardware flow control; a NULL modem adapter supports this. The table below shows the pin configuration for NULL modem cables.
Table 42-1 Pin Configuration for NULL Modem Cables
Host |
Printer |
|
---|---|---|
Mini-Din-8 |
25-Pin D-sub |
25-Pin D-sub |
- |
1 (FG) |
1(FG) |
3(TD) |
2(TD) |
3(RD) |
5(RD) |
3(RD) |
2(TD) |
6(RTS) |
4(RTS) |
5(CTS) |
2(CTS) |
5(CTS) |
4(RTS) |
4(SG) |
7(SG) |
7(SG) |
7(DCD) |
6(DSR), 8(DCD) |
20(DTR) |
1(DTR) |
20(DTR) |
6(DSR), 8(DCD) |
Check that any hardware switches for the ports are set properly.
See the printer documentation for the correct settings.
Check that the printer is operational.
Use the printer's self-test feature, if the printer has one. Check the printer documentation for information about printer self-testing.
Check that the baud settings for the computer and the printer are correct.
If the baud settings are not the same for both the computer and the printer, sometimes nothing will print, but more often you get incorrect output. For instructions, see "How to Troubleshoot Incorrect Output".
Check that the network link between the print server and the print client is set up correctly.
print_client# ping print_server print_server is alive print_server# ping print_client print_client not available |
If the message says the system is alive, you know you can reach the system, so the network is all right. The message also tells you that either a name service or the local /etc/hosts file has translated the host (system) name you entered into an IP address; otherwise, you would need to enter the IP address.
If you get a not available message, try to answer the following questions: How is NIS or NIS+ set up at your site? Do you need to take additional steps so that print servers and print clients can communicate with one another? If your site is not running NIS or NIS+, have you entered the IP address for the print server in each print client's /etc/hosts file, and entered all print client IP addresses in the /etc/hosts file of the print server?
(On a SunOS 5.0-5.1 print server only) Check that the listen port monitor is configured correctly.
(On a SunOS 5.0-5.1 print server only) Check that the network listen services are registered with the port monitor on the print server.
This procedure uses the printer luna as an example of checking basic LP print service functions.
On both the print server and print client, make sure that the LP print service is running.
Check whether the LP scheduler is running.
# lpstat -r scheduler is running |
If the scheduler is not running, become superuser or lp, and start the scheduler.
# /usr/lib/lp/lpsched |
If you have trouble starting the scheduler, see "How to Unhang the LP Print Service".
On both the print server and print client, make sure that the printer is accepting requests.
Check that the printer is accepting requests.
# lpstat -a mars accepting requests since Jul 12 14:23 1999 luna not accepting requests since Jul 12 14:23 1999 unknown reason |
This command verifies that the LP system is accepting requests for each printer configured for the system.
If the printer is not accepting requests, become superuser or lp, and allow the printer to accept print requests.
# accept luna |
The specified printer now accepts requests.
On both the print server and print client, make sure that the printer is enabled to print submitted print requests.
Check that the printer is enabled.
# lpstat -p luna printer luna disabled since Jul 12 14:25 1999. available. unknown reason |
This command displays information about printer status. You can omit the printer name to obtain information about all printers set up for the system. The following example shows a printer that is disabled.
If the printer is disabled, become superuser or lp, and enable the printer.
# enable luna printer "luna" now enabled. |
The specified printer is enabled to process print requests.
On the print server, make sure that the printer is connected to the correct serial port.
Check that the printer is connected to the correct serial port.
# lpstat -t scheduler is running system default destination: luna device for luna: /dev/term/a |
The message device for printer-name shows the port address. Is the cable connected to the port to which the LP print service says is connected? If the port is correct, skip to Step 5.
Become superuser or lp.
Change the file ownership of the device file that represents the port.
# chown lp device-filename |
This command assigns the special user lp as the owner of the device file. In this command, device-filename is the name of the device file.
Change the permissions on the printer port device file.
# chmod 600 device-filename |
This command allows only superuser or lp to access the printer port device file.
On both the print server and print client, make sure that the printer is configured properly.
Check that the printer is configured properly.
# lpstat -p luna -l printer luna is idle. enabled since Jul 12 14:24 1999. available Content types: postscript Printer types: PS |
The above example shows a PostScript printer that is configured properly, and that is available to process print requests. If the printer type and file content type are correct, skip to Step 6.
If the printer type or file content type is incorrect, try setting the print type to unknown and the content type to any on the print client.
# lpadmin -p printer-name -T printer-type -I file-content-type |
On the print server, make sure that the printer is not faulted.
Check that the printer is not waiting because of a printer fault.
# lpadmin -p printer-name -F continue |
This command instructs the LP print service to continue if it is waiting because of a fault.
Force an immediate retry by re-enabling the printer.
# enable printer-name |
(Optional) Instruct the LP print service to enable quick notification of printer faults.
# lpadmin -p printer-name -A 'write root' |
This command instructs the LP print service to set a default policy of writing root--sending the printer fault message to the terminal on which root is logged in--if the printer fails. This may help you get quick notification of faults as you try to fix the problem.
Make sure that the printer is not set up incorrectly as a login terminal.
It is easy to mistakenly set up a printer as a login terminal, so be sure to check this possibility even if you think it does not apply.
Look for the printer port entry in the ps -ef command output.
# ps -ef root 169 167 0 Apr 04 ? 0:08 /usr/lib/saf/listen tcp root 939 1 0 19:30:47 ? 0:02 /usr/lib/lpsched root 859 858 0 19:18:54 term/a 0:01 /bin/sh -c \ /etc/lp /interfaces/luna luna-294 rocket!smith "passwd\n## # |
In the output from this command, look for the printer port entry. In the above example, port /dev/term/a is set up incorrectly as a login terminal. You can tell by the "passwd\n## information at the end of the line. If the port is set correctly, skip the last steps in this procedure.
Cancel the print request(s).
# cancel request-id |
In this command, request-id is the request ID number for a print request to be canceled.
Set the printer port to be a nonlogin device.
# lpadmin -p printer-name -h |
Check the ps -ef command output to verify that the printer port is no longer a login device.
If you do not find the source of the printing problem in the basic LP print service functions, continue to one of the following procedures for the specific client/server case that applies.
Check the basic functions of the LP print service on the print server, if you have not done so already.
For instructions on checking basic functions, see "To check the basic functions of the LP print service: ". Make sure that the printer works locally before trying to figure out why nothing prints when a request is made from a print client.
Check the basic functions of the LP print service on the print client, if you have not done so already.
For instructions on checking basic functions, see "To check the basic functions of the LP print service: ". On the print client, the LP scheduler has to be running, and the printer has to be enabled and accepting requests before any request from the client will print.
For most of the following steps, you must be logged in as root or lp.
On SunOS 5.1 print client only, make sure that the print server is identified as type s5 by viewing the Modify Printer window in Admintool.
Verify that the print server is operating properly.
# lpstat -t luna scheduler is running system default destination: luna device for luna: /dev/term/a luna accepting requests since Jul 12 14:26 1999 printer luna now printing luna-314. enabled since Jul 12 14:26 1999. available. luna-129 root 488 Jul 12 14:32 # |
The above example shows a print server up and running.
If the print server is not operating properly, go back to step 1.
Check the basic functions of the LP print service on the print client, if you have not done so already.
For instructions, see "To check the basic functions of the LP print service: ".
Make sure that the print server is accessible.
Make sure that the lpd daemon on the print server is running.
On the print server, verify the lpd daemon is running.
$ ps -ax | grep lpd 126 ? IW 0:00 /usr/lib/lpd 200 p1 S 0:00 grep lpd $ |
If the lpd daemon is running, a line is displayed, as shown in the above example. If it is not running, no process information is shown.
If lpd is not running on the print server, become superuser on the print server, and restart it.
# /usr/lib/lpd & |
Make sure that the remote lpd daemon is configured properly.
On the print server, become superuser, and invoke the lpc command.
# /usr/ucb/lpc lpc> |
Get LP status information.
lpc> status luna: queuing is enabled printing is enabled no entries no daemon present lpc> |
Status information is displayed. In the above example, the daemon is not running and needs to be restarted.
If no daemon is present, restart the daemon.
lpc> restart luna |
The daemon is restarted.
Verify that the lpd daemon has started.
lpc> status |
Quit the lpc command.
lpc> quit |
The shell prompt is redisplayed.
Make sure that the print client has access to the print server.
Check if there is an /etc/hosts.lpd file on the SunOS 4.1 print server.
On a SunOS 4.1 print server, if this file exists, it is used to determine whether an incoming print request can be accepted. If the file does not exist, all print client systems have access, so skip steps b and c.
If the file exists, see if the print client is listed in the file.
Requests from client systems not listed in the file are not transferred to the print server.
If the client is not listed, add the print client to the file.
If you get this far without pinpointing the problem, the SunOS 4.1 system is probably set up and working properly.
Make sure that the connection to the remote lpd print daemon from the print client is made correctly.
On the print client, become superuser, and verify the lpsched daemon is running.
# ps -ef | grep lp root 154 1 80 Jan 07 ? 0:02 /usr/lib/lpsched |
The lpsched daemon should be running, as shown in the above example.
Stop the LP print service.
# lpshut |
The LP print service is stopped.
Restart the LP print service.
# /usr/lib/lp/lpsched |
The LP print service is restarted.
Make sure that the remote print server is identified correctly as a SunOS 4.1 system.
Check the basic functions of the LP print service on the print server, if you have not done so already.
For instructions, see "To check the basic functions of the LP print service: ". Make sure that the printer works locally before trying to figure out why nothing prints when a request is made from a print client.
You should be logged in as superuser or lp on the system specified in the following steps.
Make sure that the print client is accessible.
On the print client, verify the printer is set up correctly.
# lpr -P luna /etc/fstab lpr: cannot access luna # |
This command shows whether the print client is working. The above example shows that the print client is not working correctly.
Make sure that the lpd daemon is running on the print client.
On the print client, make sure that there is a printcap entry identifying the printer.
Verify the printer is known.
# lpr -P mercury /etc/fstab lpr: mercury: unknown printer # |
The above example shows that the /etc/printcap file does not have an entry for the specified printer.
If there is no entry, edit the /etc/printcap file and add the following information:
printer-name|print-server:\ :lp=:rm=print-server:rp=printer-name:br#9600:rw:\ :lf=/var/spool/lpd/printer-name/log:\ :sd=/var/spool/lpd/printer-name: |
The following example shows an entry for printer luna connected to print server neptune.
luna|neptune:\ :lp=:rm=neptune:rp=luna:br#9600:rw:\ :lf=/var/spool/lpd/luna/log:\ :sd=/var/spool/lpd/luna: |
Create a spooling directory (/var/spool/lpd/printer-name) for the printer.
Make sure that the print client lpd is not in a wait state by forcing a retry.
If the print server is up and responding, the print client lpd may be in a wait state before attempting a retry.
Check the connection to the print server.
On the print client, become superuser, and check the printer log file.
# more /var/spool/lpd/luna/log |
Frequently, no information is displayed.
Also check the printer status log.
# more /var/spool/lpd/luna/status waiting for luna to come up # |
If the connection is all right, on the print server, verify the print server is set up correctly.
# lpstat -t scheduler is running system default destination: luna device for luna: /dev/term/a luna accepting requests since Jul 12 14:29 1999 luna accepting requests since Jul 12 14:29 1999 printer luna is idle. enabled since Jul 12 14:29 1999. available. # |
The above example shows a print server that is up and running.
If the print server is not running, go back to Step 1 before continuing.