Det finns ett begränsat antal ID-nummer för SCSI-objekt. Om vi antar att det största antalet målenheter per kanal på en viss styrenhet är MAX_TGT, så bör ID-numren för SCSI-målenheter på en given kanal ligga mellan 0 och (MAX_TGT - 1). Mer information finns i tillverkarens dokumentation.
ID-nummer för SCSI-målenheter på en kanal kan upprepas på andra kanaler.
Exempel 1:5-kanalsmodellen stöder maximalt fyra mål per kanal, dvs MAX_TGT = 4. Därför bör ID-numren för SCSI-målenheten på en given kanal ligga mellan 0 och 3.
Exempel 2:3-kanalsmodellen stöder maximalt sju mål per kanal, dvs MAX_TGT = 7. Därför bör ID-numren för SCSI-målenheten på en given kanal ligga mellan 0 och 6.
Om en SCSI-skivenhet inte är definierad för att ingå i en fysisk enhet på en systemenhet märks den automatiskt som en standby-enhet. Om en SCSI-skivenhet i en systemenhet inte fungerar kan det hända att data på en standby-enhet förloras på grund av ersättningsproceduren för standby-enheten. Den här ersättningsproceduren skriver över standby-enheten om den icke-fungerande skivenheten har konfigurerats med någon nivå av redundans (RAID-nivåerna 1, 5 och 6) och dess storlek är identisk med storleken på den tillgängliga standby-enheten.
Även om en standby-enhet är fysiskt ansluten kan det därför hända att systemet inte ger någon tillgång till den så att ingen information ska gå förlorad av misstag.
Utöver återskapande av skivenheter, som beskrivs i tillverkarens dokumentation, stöder dessa styrenheter inte utbyte under drift.
Om du vill lägga till eller ta bort enheter stänger du ned systemet, lägger till eller tar bort enheterna, konfigurerar om HBA:n med tillverkarens konfigurationsverktyg och konfigurerar sedan om och startar om (b -r) systemet.
Drivrutinen stöder inte bandenheter med variabel längd eller säkerhetskopiering till eller återställning av flervolymsenheter på bandenheter som är anslutna till styrenheten.
På grund av en begränsning i Mylex firmware fungerar inte SCSI-bandenheter och CD-ROM-enheter tillförlitligt på äldre kort om de är anslutna till en kanal som också innehåller SCSI-hårddiskenheter. På nyare PCI SCSI-kort som DAC960PG och DAC960PJ märks däremot inte denna begränsning. Du kan hämta den senaste firmware för alla Mylex-kort på deras webbplats.
Det går inte att använda bandblockstorlek som är större än 32 kB. Om du vill vara säker på att SCSI-enheter ska fungera bra använder du bara SCSI-enheter på en annars oanvänd kanal och med en fast blockstorlek på 32 kB eller mindre.
Långa bandkommandon (exempelvis radering av ett stort band) kan misslyckas på grund av att Mylex-styrenheterna har en tidsgräns på maximalt en timma för kommandot.
Aktivera bara tag queuing för SCSI-enheter som är officiellt testade och godkända av Mylex Corporation för DAC960-styrenheter. Du bör inaktivera tag queuing för andra enheter för att undvika problem.
Kommandot mt erase fungerar men kan rapportera följande felmeddelanden när det når slutet på bandet:
/dev/rmt/0 erase failed: I/O error
Du kan ignorera det här meddelandet.