|
6565422
|
The latest communication field in the showarchiving(8) command is not updated regularly.
|
Disabling and re-enabling archiving refreshes the latest communication field in showarchiving(8) output.
|
|
6624646
|
Sun Connection Update Manager GUI might fail to register correctly.
|
Use the CLI if you run into any GUI registration issues.
|
|
6723305
|
The XSCF Web does not show the correct daylight saving time.
|
No workaround is available. Use the showlogs(8) command to determine time during daylight savings time.
|
|
6726679
|
SNMP trap is not sent after XSCF watchdog time out. This occurs intermittently. SNMP traps will not be notified after the watchdog timeout occurs in XSCF and XSCF reset.
|
No workaround is available.
|
|
6735711
|
setemailreport(8) command cannot handle recipient email addresses that are longer than 255 characters.
|
Use email address with fewer than 255 characters.
|
|
6737039
|
WAN boot of M3000 servers fails intermittently with a panic early in the boot process. Sample output:
ERROR: Last Trap: Fast Data Access MMU Miss
%TL:1 %TT:68 %TPC:13aacc %TnPC:13aad0 %TSTATE:1605
%PSTATE:16 ( IE:1 PRIV:1 PEF:1 )
DSFSR:4280804b ( FV:1 OW:1 PR:1 E:1 TM:1 ASI:80 NC:1 BERR:1 )
DSFAR:fda6f000 DSFPAR:401020827000 D-TAG:6365206f66206000
|
Poweroff and poweron the chassis, then retry the operation.
|
|
6741770
|
SNMP trap host configuration changes are not valid until setsnmp disable and setsnmp enable.
|
Modify the SNMP setting:
XSCF> setsnmp disable
XSCF> setsnmp enable
|
|
6741895
|
When FRUs are cold-replaced (with the system off), (after poweron) the monitor process might not generate entries in the monitor log identifying the replacement operation that has occurred.
|
No workaround is available.
|
|
6742395
|
Power failure at the commercial AC supply connector to the UPS does not send notification/send trap.
|
No workaround is available.
|
|
6742502
|
The browser interface displays only the last two digits of the non-audit log size limit.
|
Do not set Archive Log limit to ’0’. Use the showarchiving(8) command to determine log size limit.
|
|
6742951
|
The setlogarchiving(8) command accepts ’-1’ for the Audit log limit and then sets the limit as "Unlimited".
|
No workaround is available.
|
|
6743842
|
The password command indicates that the [user] operand is optional but will fail if a [user] operand is not included when other options are specified.
|
No workaround is available.
Specify the [user] operand to use the password command when you specify other options.
|
|
6744772
|
Logs will not be archived when logarchiving limits are exceeded, and there is no warning message to indicate that logs are no longer being archived.
|
Periodically, run the showarchiving(8) command and adjust limits as needed.
Or, as the used log archiving space approaches the defined limit manually rotate the existing logs on the log archiving host.
|
|
6755112
|
During the domain operation, after the XSCF reset due to the XSCF unit failure, the hardware status shows Deconfigure in the status of CPU and memory.
|
Replace the motherboard unit only. When no failure is found on the memory, you do not need to replace the memory.
|
|
6755113
|
During the firmware update, there might be the following output message and a XSCF panic might occur.
kernel BUG in jffs2_do_read_inode
at fs/jffs2/readinode.c:XXX!
|
Reset XSCF and use the flashupdate(8) command again.
|
|
6755986
|
In Internet Explorer 6 or 7, clicking on the [Reset] button then the [OK] button from the Settings->Audit->Add Policy poupup screen will log the user out with message:
Error
Session Error
Session ID has been expired
|
Log back into the browser interface and use the backspace key to clear text in the ’User’ text box of the popup screen instead of using the Reset button.
|
|
6757064
|
The error log "XSCF FMEM write error" recorded and the firmware update might fail.
|
Power off (AC OFF) the system, and power on (AC ON) again. Then, re-execute the firmware update.
|
|
6757614
|
The network configuration on the XSCF Web does not support the function equivalent to the setnetwork -r option. And when you specified localhost or localdomain to the host name or the domain name, the error message "SessionID has expired" appears.
|
Use the setnetwork -r command on the XSCF shell.
|
|
6761674
|
The first usage of the OBP command probe-scsi-all might not show all devices connected via the external SAS port.
|
Retry the probe-scsi-all command.
|
