/opt/SUNWvts/bin/alarmtest standard_arguments -o enet=E(nable)/D(isable),epattype=seq+rand,epkts=number_packets,target=IP_address, etest=I+E+H+P,serial=E(nable)/D(isable),slb=I+E,spattype=seq+rand, stest=c+d+u+v, pccard=E(nable)/D(isable),pccardtype=modem/serial, flash=E(nable)/D(isable),seeprom=E(nable)/D(isable),tod=E(nable)/D(isable), ttyubaud=ALL|specific_baud,ttyvbaud=ALL|specific_baud, aport=[E]nable|[D]isable,anum=0+1+2+3,a0on=On|Off/|T]oggle, a1on=On|Off|[T]oggle,a2on=On|Off|[T]oggle,a3on=On|Off|[T]oggle
Table 3-3 alarmtest Command-Line Syntax
Argument |
Explanation |
---|---|
enet=E(nable)/D(isable) |
Enables or disables Ethernet testing. |
epattype=seq+rand |
Selects the type of data pattern for Enet_Test: Sequential, Random, or both. |
epkts=number_packets |
Specifies the number of data packets to be sent in one test loop. |
target=IP_address |
Specifies the IP address of a host to use for the ping test. |
etest=I+E+H+P |
Selects any or all internal, external, Phy, or ping tests. |
serial=E(nable)/D(isable) |
Enables or disables serial_test. |
slb=I+E |
Selects internal loopback, external loopback, or both. |
spattype=seq+rand |
Selects the type of data pattern for serial_test: Sequential, Random, or both. |
stest=c+d+u+v |
Selects ports to be tested: c, d, u, or v. |
pccard=E(nable)/D(isable) |
Enables or disables PC card (PCMCIA) testing. |
pccardtype=modem/serial |
Specifies the card type for the PC Card: modem or serial i/o. Default is modem. |
flash=E(nable)/D(isable) |
Enables or disables the flash checksum test. |
seeprom=E(nable)/D(isable) |
Enables or disables the SEEPROM checksum test. |
tod=E(nable)/D(isable) |
Enables or disables the TOD checksum test. |
ttyubaud=ALL| specific_baud |
Defines baud rates to be used in testing the alarmcard's COM1 port. |
ttyvbaud=ALL| specific_baud |
Defines baud rates to be used in testing the alarmcard's COM2 port. |
aport=[E]nable|[D]isable |
Enables or disables the alarmport test. |
anum=0+1+2+3 |
Selects any or all alarm port to be tested: 0, 1, 2, 3 |
a0on=On|Off/|T]oggle |
Turns on, turns off, or toggles (on then off) alarm port 0. |
a1on=On|Off|[T]oggle |
Turns on, turns off, or toggles (on then off) alarm port 1. |
a2on=On|Off|[T]oggle |
Turns on, turns off, or toggles (on then off) alarm port 2. |
a3on=On|Off|[T]oggle |
Turns on, turns off, or toggles (on then off) alarm port 3. |
64-bit tests are located in the sparcv9 subdirectory: /opt/SUNWvts/bin/sparcv9/testname. If a test is not present in this directory, then it may only be available as a 32-bit test. For more information refer to "32-Bit and 64-Bit Tests".