Collecting System Activity Data Automatically (sar)

Collecting System Activity Data Automatically (`sar`)

Three commands are involved in the automatic collection of system activity data: sadc, sa1, and sa2.

The sadc data collection utility periodically collects data on system activity and saves the data in a file in binary format, one file for each 24-hour period. You can set up the sadc command to run periodically (usually once each hour), and whenever the system boots to multiuser mode. The data files are placed in the /var/adm/sa directory. Each file is named sadd, where dd is the current date. The format of the command is as follows:

/usr/lib/sa/sadc [t n] [ofile]

The command samples n times with an interval of t seconds, which should be greater than five seconds between samples. This command then writes to the binary ofile file, or to standard output.

Running the `sadc` Command When Booting

The sadc command should be run at system boot time to record the statistics from when the counters are reset to zero. To make sure that the sadc command is run at boot time, the svcadm enable system/sar:default command writes a record to the daily data file.

The command entry has the following format:

/usr/bin/su sys -c "/usr/lib/sa/sadc /var/adm/sa/sa`date +%d`"

Running the `sadc` Command Periodically With the `sa1` Script

To generate periodic records, you need to run the sadc command regularly. The simplest way to do so is to uncomment the following lines in the /var/spool/cron/crontabs/sys file:

# 0 * * * 0-6 /usr/lib/sa/sa1
# 20,40 8-17 * * 1-5 /usr/lib/sa/sa1
# 5 18 * * 1-5 /usr/lib/sa/sa2 -s 8:00 -e 18:01 -i 1200 -A

The sys crontab entries do the following:

The first two crontab entries cause a record to be written to the /var/adm/sa/sadd file every 20 minutes from 8 a.m. to 5 p.m., Monday through Friday, and every hour on the hour otherwise.
The third entry writes a record to the /var/adm/sa/sardd file hourly, Monday through Friday, and includes all sar options.

You can change these defaults to meet your needs.

Producing Reports With the `sa2` Shell Script

Another shell script, sa2, produces reports rather than binary data files. The sa2 command invokes the sar command and writes the ASCII output to a report file.

Setting Up Automatic Data Collection (`sar`)

The sar command can be used either to gather system activity data itself or to report what has been collected in the daily activity files that are created by the sadc command.

The sar command has the following formats:

sar [-aAbcdgkmpqruvwy] [-o file] t [n]

sar [-aAbcdgkmpqruvwy] [-s time] [-e time] [-i sec] [-f file]

The following sar command samples cumulative activity counters in the operating system every t seconds, n times. The t should be five seconds or greater. Otherwise, the command itself might affect the sample. You must specify a time interval in which to take the samples. Otherwise, the command operates according to the second format. The default value of n is 1. The following example takes two samples separated by 10 seconds. If the -o option were specified, samples are saved in binary format.

$ sar -u 10 2

Other important information about the sar command includes the following:

With no sampling interval or number of samples specified, the sar command extracts data from a previously recorded file. This file is either the file specified by the -f option or, by default, the standard daily activity file, /var/adm/sa/sadd, for the most recent day.
The -s and -e options define the starting time and the ending time for the report. Starting and ending times are of the form hh[:mm[:ss]], where hh, mm, and ss represent hours, minutes, and seconds.
The -i option specifies, in seconds, the intervals between record selection. If the -i option is not included, all intervals that are found in the daily activity file are reported.

The following table lists the sar options and their actions.

Table 13-2 Options for the sar Command

Option	Actions
`-a`	Checks file access operations
`-b`	Checks buffer activity
`-c`	Checks system calls
`-d`	Checks activity for each block device
`-g`	Checks page-out and memory freeing
`-k`	Checks kernel memory allocation
`-m`	Checks interprocess communication
`-nv`	Checks system table status
`-p`	Checks swap and dispatch activity
`-q`	Checks queue activity
`-r`	Checks unused memory
`-u`	Checks CPU utilization
`-w`	Checks swapping and switching volume
`-y`	Checks terminal activity
`-A`	Reports overall system performance, which is the same as entering all options.

Using no option is equivalent to calling the sar command with the -u option.

How to Set Up Automatic Data Collection

Become superuser or assume an equivalent role.
Roles contain authorizations and privileged commands. For more information about roles, see Configuring RBAC (Task Map) in System Administration Guide: Security Services.
Run the svcadm enable system/sar:default command.
This version of the sadc command writes a special record that marks the time when the counters are reset to zero (boot time).
Edit the /var/spool/cron/crontabs/sys crontab file.
Note - Do not edit a crontab file directly. Instead, use the crontab -e command to make changes to an existing crontab file.
```
# crontab -e sys
```

Uncomment the following lines:

0 * * * 0-6 /usr/lib/sa/sa1
20,40 8-17 * * 1-5 /usr/lib/sa/sa1
5 18 * * 1-5 /usr/lib/sa/sa2 -s 8:00 -e 18:01 -i 1200 -A

For more information, see the crontab(1) man page.

Skip Navigation Links
Exit Print View
	System Administration Guide: Advanced Administration Oracle Solaris 10 8/11 Information Library

Running the sadc Command When Booting

Running the sadc Command Periodically With the sa1 Script

Producing Reports With the sa2 Shell Script

Setting Up Automatic Data Collection (sar)