Understanding the Server Module
Front and Rear Panel Components
Confirming Server Module and Site Specifications
Plan Communication With the Server Module During Installation
Prepare the Modular System and Server Module
Insert the Server Module Into the Chassis
Powering On the Server Module for the First Time
Method 1a – Power On the Host Through the CMM (Web Interface)
Method 1b – Power On the Host Through the CMM (CLI)
Method 3 – Power On the Host Through the Front Panel (SP CLI)
Configuring the Oracle Solaris OS
Install Oracle Solaris Software From the Network
Oracle Solaris Configuration Parameters
Assign a Static IP Address to the SP
Understanding System Administration Resources
Platform-Specific Oracle ILOM Features
Oracle VM Server for SPARC Overview
Hardware Management Pack Overview
Source for Downloading Hardware Management Pack Software
Hardware Management Pack Documentation
Display the Oracle ILOM -> Prompt
Power On the Server (Oracle ILOM)
Power Off the Server (Oracle ILOM)
Reset the Server (Oracle Solaris OS)
Reset the Server (Oracle ILOM)
Reset the SP to Default Values
Important Hardware RAID Guidelines
Prepare to Use the FCode Utility
Hot Spare Drives in RAID Volumes (LSI)
Determining If a Drive Has Failed
RAID Drive Replacement Strategies
Changing Server Identification Information
Change Customer Data on FRU PROMs
Change System Identifier Information
Restore the Host Power State at Restart
Specify the Host Power State at Restart
Disable or Re-Enable the Host Power-On Delay
Specify Parallel Boot of the SP and Host
Configure Host Behavior (Keyswitch State)
Disable or Re-Enable Network Access to the SP
Display the DHCP Server IP Address
Display the IP Address of the SP
Using an In-band Connection to the SP
Configure the Host Boot Mode (Oracle VM Server for SPARC)
Change the Host Boot Mode Behavior at Reset
Manage the Host Boot Mode Script
Display Host Boot Mode Expiration Date
Override OBP Settings to Reset the Server
Configuring Server Behavior at Restart
Specify Behavior When the Host Resets
Specify Behavior When the Host Stops Running
Specify Behavior at Boot Timeout
Specify Behavior if Restart Fails
Specify Maximum Restart Attempts
Enabling Automatic System Recovery
Identifying WWN-Designated SAS2 Devices
Mapping WWN Values to Hard Drives (OBP probe-scsi-all Command)
Identify a Disk Slot Using prtconf (Oracle Solaris OS)
WWN Syntax in an OS Installation on an Individual Drive
WWN Syntax in an OS Installation on a RAID Volume
Front and Rear Panel Components
Interpreting Log Files and System Messages
Checking if Oracle VTS Software Is Installed
Find the Modular System Chassis Serial Number
Find the Server Module Serial Number
Preparing the Server Module for Removal
Remove the Server Module From the Modular System
Clear the Fault and Verify the Functionality of the Replacement DIMM
Replacing the Server Module Enclosure Assembly (Motherboard)
Transfer Components to Another Enclosure Assembly
Returning the Server Module to Operation
Install the Server Module Into the Modular System
Power On the Host (Oracle ILOM)
You can access the server module SP by first accessing the chassis CMM ILOM through a terminal or terminal emulator connected to the RJ-45 serial port on the chassis. Then you can connect to the server module SP through the CLI of the CMM ILOM software.
8N1 (eight data bits, no parity, one stop bit)
9600 baud (the default, but can be set to any standard rate up to 57600)
Disable hardware flow control (CTS/RTS)
Refer to the modular system chassis documentation for the location of the serial port.
The serial port requires a cable with these pin assignments.
|
The connection between the terminal device and the CMM is established.
If you connected to the serial port before the powering on the modular system, you will see boot messages. The CMM ILOM software displays its login prompt:
ORACLECMMnnnnnnnnnn login:
The first string in the prompt is the default host name, which consists of the prefix ORACLECMM followed by the CMM ILOM MAC address. The MAC address for each CMM and SP is unique.
The factory default ILOM root password is changeme, but might have been changed in your environment.
You are now logged in to the CMM ILOM web interface.
After you have successfully logged in, the CMM ILOM displays its default command prompt:
->
-> cd /CH/BLn/SP/cli
Replace n with an integer that identifies the target server module (the slot for which the server module is installed).
-> start Are you sure you want to start /CH/BL0/SP/cli (y/n)? y start: Connecting to /CH/BL0/SP/cli using Single Sign On
Note - The CMM ILOM logs into the server module ILOM using the user name in the user target under /CH/BLn/SP/cli (where n is the slot where the server module is installed).
-> start /SYS Are you sure you want to start /SYS (y/n)? y
The server module initializes.
When the ILOM prompt appears, type:
-> start /HOST/console Are you sure you want to start /HOST/console (y/n)? y Serial console started. To stop, type #.
The server module might take several minutes to complete POST. If a boot device installed with Oracle Solaris OS is accessible locally, the server module boots. Otherwise, the server module uses the boot net command to seek a boot device on the network.
You are now connected to the server module host.
You can now configure the Oracle Solaris OS to meet your needs. See Configuring the Oracle Solaris OS.