Displays the drives available in a drive group. The details about a selected drive are displayed on the right-hand side of the dialog.
Provides the operational state of the drive in the drive group. Oracle FS System Manager (GUI) displays a status icon followed by the drive state.
The drive is a member of the drive group.
The drive is operating normally, but is not a member of a drive group.
The drive is starting up.
The system has detected a failure on the drive and is currently copying the data to a target drive. The drive state changes to Failed when copying is complete.
The system has detected a failure on another drive and is currently copying the data to this target drive.
An active spare drive is copying data to this drive.
The connection to the drive is limited to only a single Controller.
The drive is not a member of this drive group. Accept this drive using the associated System Alert to make the drive a member of the drive group.
The drive is not found in the Drive Enclosure.
The drive is a target of a rebuild operation for a drive group.
The drive has failure history, but is now online and is not a member of a drive group.
The drive has failure history. The drive is now online and is a member of a drive group.
The system is in shutdown mode and cannot access the drive.
The system is unable to read the drive state.
The drive has experienced a failure.
The drive is currently being restored.
Indicates the operational state of the drive.
Indicates the manufacturers model number of the drive.
Indicates the serial number of the drive.
Indicates the firmware version number of the drive.
Indicates the Drive Enclosure slot number where the drive is installed.
Specifies the category of physical media that comprises the drive group.
Specifies that the data is stored on solid state drives (SSDs) that are optimized for the performance of balanced read and write operations.
Specifies that the data is stored on SSDs that are optimized for the performance of capacity and for read operations. The write performance for this Storage Class is sacrificed somewhat to achieve the optimizations for read performance and for capacity.
Specifies that the data is stored on high-speed hard disk drives (HDDs). This Storage Class sacrifices some capacity to reduce the access time and the latency of the read operations and of the write operations.
Specifies that the data is stored on high-capacity, rotating HDDs. This Storage Class optimizes capacity at some sacrifice of speed. For a storage system that does not include tape storage as an option, this Storage Class always provides the lowest cost for each GB of capacity.
Indicates the unique identifier of the Drive Enclosure.
Indicates the storage capacity of the drive.
(SSD only) Indicates the remaining months in the life of the drive.
Make the drive group the primary drive group within the Drive Enclosure. The primary drive group contains system configuration data.
Indicates the types of RAID data protection that is provided by the selected drive group.
Each entry in the table represents a particular set of minimum allocation units (MAUs) in the drive group. Each of the MAUs in a given set has the same level of RAID protection, forming a RAID protection segment for the drive group.
Indicates that each of the MAUs in the RAID protection segment uses one set of parity bits to protect against the loss of one drive in the drive group. Single parity is implemented as a variant of the RAID 5 storage technology.
Indicates that each of the MAUs in the RAID protection segment uses two sets of parity bits to protect against the loss of one or two drives in the drive group. Double parity is implemented as a variant of the RAID 6 storage technology.
Indicates that each of the MAUs in the RAID protection segment is written across two drives in the drive group. Mirrored RAID is implemented as a variant of the RAID 10 storage technology.
Indicates that the drive group is accessible and no action is required.
Indicates that the drive has failed in the drive group, but the drive group is still accessible. Replace the failed drive. If the drive group is the primary drive group, then replace the drive immediately. The primary drive group contains system overhead, including all system configuration data.
Indicates that two or more of the drives have failed. The drive group can become inaccessible unless you replace the drives.
Indicates that multiple drives have failed. The drive group is not accessible. Replace the failed drives. After the failed drives are replaced, the drive group becomes accessible.
Indicates that the drive status information is not available to display.