Oracle^® VM Server for SPARC 3.5.0.2 补充发行说明

文档问题

ldm(1M) 手册页：更新了 ldm add-vsw 用法概要

更新了 ldm add-vsw 命令的命令行用法概要，指出必须为 vsw-relay-mode 属性指定一个值。以下是更新后的命令行用法概要：

ldm add-vsw [-q] [default-vlan-id=VLAN-ID] [pvid=port-VLAN-ID] [vid=VLAN-ID1,VLAN-ID2,...] 
  [linkprop=phys-state] [mac-addr=MAC-address] [net-dev=device] [mode=sc] [mtu=size]
  [id=switch-ID] [inter-vnet-link=auto|on|off]] [vsw-relay-mode=local|remote] vswitch-name
  domain-name

ldm(1M) 手册页：更新了 ldm set-vsw 用法概要

更新了 ldm set-vsw 命令的命令行用法概要，指出以下属性值要求：

• vsw-relay-mode 必须指定一个值

• 不能重置 inter-vnet-link 值

• 可以重置 net-dev、mtu 和 pvid 值

以下是更新后的命令行用法概要：

ldm set-vsw [-q] [pvid=[port-VLAN-ID]] [vid=[[+|-]VLAN-ID1,VLAN-ID2,...]] [mac-addr=MAC-address]
  [net-dev=[device]] [linkprop=[phys-state]] [mode=[sc]] [mtu=[size]]
  [inter-vnet-link=auto|on|off] [vsw-relay-mode=local|remote] vswitch-name

ldm(1M) 手册页：更新了 ldm add-vnet 用法概要

更新了 ldm add-vnet 命令的命令行用法概要，指出 custom 属性必须指定一个值。以下是更新后的命令行用法概要：

ldm add-vnet [mac-addr=MAC-address] [pvid=port-VLAN-ID] [pvlan=secondary-vid,pvlan-type]
  [protection=protection-type[,protection-type],...] [auto-alt-mac-addrs=num]
  [custom=enable|disable] [custom/max-vlans=num] [custom/max-mac-addrs=num]
  [allowed-ips=IP-address[,IP-address]...] [priority=high|medium|low] [cos=0-7]
  [allowed-dhcp-cids=[MAC-address|hostname,MAC-address|hostname,...]]
  [alt-mac-addrs=auto|MAC-address[,auto|MAC-address,...]] [vid=VLAN-ID1,VLAN-ID2,...]
  [linkprop=phys-state] [id=network-ID] [mtu=size] [maxbw=value] if-name vswitch-name
  domain-name

ldm(1M) 手册页：更新了 ldm set-vnet 用法概要

更新了 ldm set-vnet 命令的命令行用法概要，指出以下属性值要求：

• custom 必须指定一个值

• 可以重置 mtu 和 pvid 值

以下是更新后的命令行用法概要：

ldm set-vnet [mac-addr=MAC-address] [vswitch=vswitch-name] [mode=] [pvid=[port-VLAN-ID]]
  [pvlan=[secondary-vid,pvlan-type]] [protection=[[+|-]protection-type[,protection-type],...]]
  [allowed-ips=[[+|-]IP-address[,IP-address]...]] [priority=high|medium|low] [cos=0-7]
  [allowed-dhcp-cids=[[+|-]MAC-address|hostname,MAC-address|hostname,...]]
  [alt-mac-addrs=[[+|-]auto|MAC-address[,auto|MAC-address,...]]] [linkprop=[phys-state]] 
  [mtu=[size]] [vid=[[+|-]VLAN-ID1,VLAN-ID2,...]] [auto-alt-mac-addrs=[+]num]
  [custom=enable|disable] [custom/max-vlans=[num]] [custom/max-mac-addrs=[num]]
  [maxbw=[value]] if-name domain-name