Removing an Allowed Affected Destination Field Screen

This procedure is used to remove an allowed affected destination field (DESTFLD) screen from the database using the dlt-scr-destfld command. The parameters used by the dlt-scr-destfld command are shown in the Gateway Screening Attributes section. The general rules that apply to configuring gateway screening entities are shown in the Gateway Screening Configuration section.

The example in this procedure removes the allowed DESTFLD screen fld5 from the database.

Note:

If you using multiple-part ITU national point codes with gateway screening, see the 14-Bit ITU National Point Code Formats section.

The allowed DESTFLD screen can be referenced by one of the following screens.

Allowed SIO
Allowed DPC
Blocked DPC

Verifying the Gateway Screening Configuration

Enter the following commands to verify that none of these screens reference the allowed CGPA screen being removed from the database.

rtrv-scr-sio:nsfi=destfld
rtrv-scr-dpc:nsfi=destfld
rtrv-scr-blkdpc:nsfi=destfld

Gateway Screening Configuration Procedures

To change the NSFI of any of these screens, perform one of these procedures.

Display the allowed DESTFLD screens in the database using the rtrv-scr-destfld command.
The following is an example of the possible output.
```
rlghncxa03w 06-10-25 15:25:30 GMT EAGLE5 36.0.0
SCREEN = ALLOWED DESTFLD
SR    REF  RULES
FLD5  YES     1
IEC   YES     6
WRD2  YES     1
WRD4  YES     9
```
From the rtrv-scr-destfld output, display the allowed DESTFLD screen you wish to remove using the rtrv-scr-destfld command with the screening reference name. For this example, enter this command.

rtrv-scr-destfld:sr=fld5

The following is an example of the possible output.
```
rlghncxa03w 06-10-25 15:25:30 GMT  EAGLE5 36.0.0
SCREEN = ALLOWED DESTFLD
SR    NI       NC       NCM      NSFI   NSR/ACT
fld5  100      100      100      STOP   cr
```
Enter the commands in the Verifying the Gateway Screening Configuration section to verify that the screen being removed is not referenced by other screens in the database.

If the screen being removed is referenced by other screens, perform the procedures shown in the Gateway Screening Configuration Procedures section to change the NSFI of those screens to reference other screens or change the NSFI of these screens to STOP.
Remove the allowed DESTFLD screen from the database using the dlt-scr-destfld command with the screening reference name shown in the rtrv-scr-destfld output in step 1 and with the point code parameter values (ni, nc, ncm, or zone, area, id, npc, msa, ssa, or sp) of the screen being removed from the database.
The values for these parameters must be entered exactly as shown in the rtrv-scr-destfld output.

To remove an entry containing either an ITU-I or a 14-bit ITU-N spare point code, the pcst=s parameter must be specified with the dlt-scr-destfld command.

To remove an entry containing either an ITU-I or a 14-bit ITU-N non-spare point code, the pcst parameter does not have to be specified with the dlt-scr-destfld command. If the pcst parameter is specified, the value must be none.

For this example, enter this command.

dlt-scr-destfld:sr=fld5:ni=100:nc=100:ncm=100

A message similar to the following should appear.
```
rlghncxa03w 06-10-25 15:26:30 GMT  EAGLE5 36.0.0
DLT-SCR-DESTFLD: SCREEN SET AFFECTED - FLD5  0% FULL
DLT-SCR-DESTFLD: MASP A - COMPLTD
```
Verify the changes using the rtrv-scr-destfld command with the screening reference name used in step 3.
For this example, enter this command.

rtrv-scr-destfld:sr=fld5

The following is an example of the possible output.
```
E2573 Cmd Rej: SR or NSR does not reference an existing SR
```
This message shows that the specified screening reference name is not in the database and the action of the dlt-scr-destfld command in step 3 was successful. If the specified screening reference name contained more than one entry when the dlt-scr-destfld command was executed in step 3, the rtrv-scr-destfld:sr= command output would show the remaining entries in the screening reference instead of error message E2573.

Backup the new changes using the chg-db:action=backup:dest=fixed command.

The following messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.

BACKUP (FIXED) : MASP A - Backup starts on active MASP.
BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete.
BACKUP (FIXED) : MASP A - Backup starts on standby MASP.
BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.

Figure 7-4 Removing an Allowed Affected Destination Field Screen

Sheet 1 of 2

Sheet 2 of 2