Removing an IPSG M3UA Signaling Link

This procedure is used to remove an IPSG M3UA signaling link from the database using the dlt-slk command. The dlt-slk command uses these parameters.

:loc  – The card location of the IPSG card that the IPSG M3UA signaling link is assigned to.

:link – The signaling link on the card specified in the loc parameter.

:force – This parameter must be used to remove the last link in a linkset without having to remove all of the routes that referenced the linkset.

The IPSG M3UA signaling link cannot be removed if removing the IPSG M3UA signaling link will cause the number of IS-NR IPSG M3UA signaling links in the linkset to be less than the NUMSLKALW, NUMSLKRSTR, or NUMSLKPROH values shown in the rtrv-ls output. The NUMSLKALW, NUMSLKRSTR, and NUMSLKPROH values are defined as follows.
  • NUMSLKALW - specifies the number of IS-NR (in-service normal) signaling links in the IPSG M3UA linkset required to change the state of the linkset from the Restricted or Prohibited state to the Allowed state.
  • NUMSLKRSTR - specifies the number of signaling links in the IPSG M3UA linkset required to change the state of the linkset from the Allowed state to the Restricted state.
  • NUMSLKPROH - specifies the number of signaling links in the IPSG M3UA linkset required to change the state of the linkset from the Allowed or Restricted state to the Prohibited state.

For more information about the NUMSLKALW, NUMSLKRSTR, and NUMSLKPROH values, refer to the Configuring IPSG M3UA Linkset Options procedure.

If the NUMSLKALW, NUMSLKRSTR, and NUMSLKPROH values are 1 or 0, then the IPSG M3UA signaling link can be removed. The value 0 is shown in the rtrv-ls output as a number with an asterisk (*), for example, 2*.

Canceling the RTRV-SLK Command

Because the rtrv-slk command used in this procedure can output information for a long period of time, the rtrv-slk command can be canceled and the output to the terminal stopped. There are three ways that the rtrv-slk command can be canceled.

  • Press the F9 function key on the keyboard at the terminal where the rtrv-slk command was entered.
  • Enter the canc-cmd without the trm parameter at the terminal where the rtrv-slk command was entered.
  • Enter the canc-cmd:trm=<xx>, where <xx> is the terminal where the rtrv-slk command was entered, from another terminal other that the terminal where the rtrv-slk command was entered. To enter the canc-cmd:trm=<xx> command, the terminal must allow Security Administration commands to be entered from it and the user must be allowed to enter Security Administration commands. The terminal’s permissions can be verified with the rtrv-secu-trm command. The user’s permissions can be verified with the rtrv-user or rtrv-secu-user commands.

For more information about the canc-cmd command, go to Commands User's Guide.

  1. Display the IPSG signaling links by entering this command.

    rtrv-slk:type=ipsg

    This is an example of the possible output.

    
    rlghncxa03w 06-10-19 21:16:37 GMT EAGLE5 36.0.0
    
    LOC  LINK LSN         SLC TYPE     ANAME           SLKTPS
    2202 A    lsnlp1      0   IPSG     assoc2          500
    2205 A    lsnip1      1   IPSG     assoc3          500
    2204 A    ls04        0   IPSG     assoc1          500
    2207 A    lsnlp3      0   IPSG     assoc11         850
    2211 A    lsnlp4      0   IPSG     assoc12         950
    2213 A    lsnip5      0   IPSG     assoc4          750
    2215 A    lsnlp2      1   IPSG     assoc5          1000
    
    
    
  2. Display the associations assigned to the IPSG card containing the signaling link that will be removed by entering the rtrv-assoc command and specifying the card location of the IPSG card. For this example, enter this command.

    For this example, enter this command.

    rtrv-assoc:loc=2207

    This is an example of possible output.

    
    rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0
                    CARD IPLNK
    ANAME           LOC  PORT  LINK ADAPTER LPORT RPORT OPEN ALW
    assoc11         2207 A     A    M3UA    1030  1030  YES  YES
    
    IP Appl Sock/Assoc table is (7 of 4000) 1% full
    Assoc Buffer Space Used (16 KB of 3200 KB) on LOC = 2207
    

    If the ADAPTER value of the associations shown in this step is M3UA, continue the procedure with 3.

    If the ADAPTER value for the associations is M2PA, perform one of these actions.
    • If you wish to remove the signaling link assigned to this card, perform the Removing an IPSG M2PA Signaling Link.
    • If you do not wish to remove the signaling link assigned to this card, select another card from 1 and repeat this step.
  3. Display the linkset that contains the signaling link that is being removed by entering the rtrv-ls command with the name of the linkset shown in the LSN column in 1. For this example, enter this command.

    rtrv-ls:lsn=lsnlp3

    This is an example of the possible output.

    rlghncxa03w 08-05-27 16:43:42 GMT EAGLE5 38.0.0
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCA   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    lsnlp3        001-001-003   none 1   1   no  A   1    off off off no    off
    
                  SPCA          CLLI         TFATCABMLQ MTPRSE ASL8
               ---------------- -----------  ---        ---    no
    
               IPSG  IPGWAPC  GTTMODE           CGGTMOD
               yes   no       CdPA               no
    
               ADAPTER    SLKTPS  LSUSEALM  SLKUSEALM  RCONTEXT   ASNOTIF
               m3ua       500     100%      80%        none       yes
    
               NUMSLKALW  NUMSLKRSTR  NUMSLKPROH
               1          1           1
    
               LOC  LINK SLC TYPE     ANAME
               2207 A    0   IPSG     assoc11
    
    Link set table is (22 of 1024) 2% full.
    

    The IPSG M3UA signaling link cannot be removed if removing the IPSG M3UA signaling link will cause the number of IS-NR IPSG M3UA signaling links in the linkset to be less than the NUMSLKALW, NUMSLKRSTR, andNUMSLKPROH values shown in the rtrv-ls output. If the NUMSLKALW, NUMSLKRSTR, andNUMSLKPROH values are 1 or 0, then the IPSG M3UA signaling link can be removed. The value 0 is shown in the rtrv-ls output as a number with an asterisk (*) is displayed in the rtrv-ls output, for example, 2*.

    If you do not wish to change the NUMSLKALW, NUMSLKRSTR, or NUMSLKPROH values, this signaling link cannot be removed and the remainder of this procedure cannot be performed.

    If you with to change the NUMSLKALW, NUMSLKRSTR, or NUMSLKPROH values, perform the Configuring IPSG M3UA Linkset Options procedure to change the required values. After the Configuring IPSG M3UA Linkset Options has been performed, continue the procedure with 4

  4. Any in-service IP connections on the signaling link being removed in this procedure must be placed out of service.

    Have the far-end node for the signaling link being removed place the M3UA associations in either the ASP-INACTIVE or ASP-DOWN state.

    • If the OPEN or ALW values for the associations is YES, continue the procedure with 5.
    • If the OPEN and ALW values for the associations is NO, continue the procedure with 6.
  5. Change the value of the open and alw parameters to no by specifying the chg-assoc command with the open=no and alw=no parameters, as necessary. For this example, enter this command.

    chg-assoc:aname=assoc11:open=no:alw=no

    When this command has successfully completed, this message should appear.

    
    rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0
    CHG-ASSOC: MASP A - COMPLTD;
    
  6. Deactivate the link to be removed using the dact-slk command, using the output from 1 to obtain the card location and link parameter value of the signaling link to be removed. For this example, enter these commands.

    dact-slk:loc=2207:link=a

    When each of these command has successfully completed, this message should appear.

    
    rlghncxa03w 06-10-07 08:41:12 GMT  EAGLE5 36.0.0
    Deactivate Link message sent to card
    
  7. Verify that the link is out of service - maintenance disabled (OOS-MT-DSBLD) using the rept-stat-slk command with the card location and link parameter values specified in 6. For this example, enter these commands.

    rept-stat-slk:loc=2207:link=a

    This is an example of the possible output.

    
    rlghncxa03w 06-10-23 13:06:25 GMT EAGLE5 36.0.0
    SLK      LSN       CLLI        PST          SST       AST
    2207,A   lsnlp3    ls07clli    OOS-MT       Unavail   ----
      ALARM STATUS       = *   0235 REPT-LNK-MGTINH: local inhibited
      UNAVAIL REASON     = LI
    
  8. Place the card that contains the signaling link shown in 7 out of service by entering the rmv-card command specifying the card location shown in 7. For this example, enter this command.

    rmv-card:loc=2207

    When this command has successfully completed, this message should appear.

    
    rlghncxa03w 06-10-07 08:41:12 GMT  EAGLE5 36.0.0
    Card has been inhibited.
    
  9. Verify that the card has been inhibited by entering the rept-stat-card command with the card location specified in 8. For this example, enter this command.

    rept-stat-card:loc=2207

    This is an example of the possible output.

    
    rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    2207   133-003-000  E5ENET    IPSG       OOS-MT-DSBLD   Isolated   -----
      ALARM STATUS       =  No Alarms.
      BLIXP   GPL version = 133-003-000
      IMT BUS A           = Disc
      IMT BUS B           = Disc
      CURRENT TEMPERATURE   =  32C ( 90F)     [ALARM TEMP:  60C (140F)]
      PEAK TEMPERATURE:     =  39C (103F)     [06-05-02 13:40]
      SIGNALING LINK STATUS
          SLK    PST                LS            CLLI
          A      OOS-MT             lsnlp2        -----------
    
    Command Completed.
    
  10. Remove the signaling link from the EAGLE using the dlt-slk command. If there is only one signaling link in the linkset, the force=yes parameter must be specified to remove the signaling link.

    In the example used in this procedure, the signaling link is the last signaling link in the linkset. Enter this command.

    dlt-slk:loc=2207:link=a:force=yes

    When this command has successfully completed, this message should appear.

    
    rlghncxa03w 06-10-07 08:41:17 GMT  EAGLE5 36.0.0
    DLT-SLK: MASP A - COMPLTD
    

    Note:

    If removing the signaling link will result in 700 or less signaling links in the database and theOAMHCMEAS value in thertrv-measopts output is on, the scheduled UI measurement reports will be enabled.
  11. Verify the changes using the rtrv-slk command, with the card location and link values specified in 10. For this example, enter this command.

    rtrv-slk:loc=2207:link=a

    When the rtrv-slk command has completed, no entry is displayed showing that the signaling link has been removed.

    
        rlghncxa03w 09-09-18 13:43:31 GMT EAGLE5 41.1.0
    E2373 Cmd Rej: Link is unequipped in the database
    
  12. Back up the new changes using the chg-db:action=backup:dest=fixed command. These messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.
    
    BACKUP (FIXED) : MASP A - Backup starts on active MASP.
    BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete.
    BACKUP (FIXED) : MASP A - Backup starts on standby MASP.
    BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.
    

Figure 6-20 Removing an IPSG M3UA Signaling Link



Sheet 1 of 3



Sheet 2 of 3



Sheet 3 of 3